Liczymy pasujące modele…
Opened up the full hexagons so can be use for connector inserts for CANBUS, fans, ERCF, PG7, & filament sensors. For inserts use these: https://www.printables.com/model/790873-voron-24-skirt-connector-insert-for-canbus-fans-er
mmu 7 ercf buffer with 7 slots instead of 5 print in abs+ layerhight 0.2mm without support
For those that use the canopy in my other files or some other variant with similar middle (will work 250, 300, or 350), this mount will allow you to attach your ERCF v2 on top. There is a new End Bypass with channels to run wiring under…
I added 5 degrees to the angle to allow my ERCF mounted cutter to clear my top hat while being mounted on the side. The ideas is that I want a short and relatively straigh filament path from ERCF to my Triedent toolhead, without looping…
Flashforge mod for ERCF v2 featuring an entry sensor Pneumatic valve connector ensures filament doesn't pop-out during filament changes Entry sensor gives Happy Hare an additional sensor to work with during filament changes. Installation…
It's a vertical mount for PCB Hartk ERCF Voron 2.4 on LGX Lite You want 4 screws m3x8 and 2 heat inserts M3XD5XL4 (Standard as for the voron 2.4)
Only modified to use a NEMA17 stepper motor ## BOM: * cnc 60T pulley (2GT, always 2GT type) * one more 20T pulley ( the same type of the ERCF original design for selector motor) * 154mm belt, (2GT close loop) * nylong washer M5 0.5mm…
I wanted to provide a 3.3V pin input to the ERCF v1.1 microfit connector, so I modified the existing design to accommodate a Molex MicroFit 3.0 6-pin connector instead of the original 5-pin connector.
This is a protective cover cap designed for the Voron ERCF Filament Stress Sensor . Its purpose is to hide and protect the wire soldering area, giving the sensor a cleaner look and additional mechanical protection. Features Protection:…
Welcome, you MMU3 or ERCF users. I was kind of fed up with the spools standing around my Core One with MMU3 (former MK4S) so I installed 2 IKEA Skadis boards behind the printer to mount the spools. However, the Prusa buffer used a lot of…
I was having issues with the standard encoder housing losing its tension over time, leading to false encoder readings. I thought back to when "springy" was released for the ercf and how much it helped with reliable tension and applied it…
v1. This mod for the ercf v2 thumper blocks lets you replace the servo with a pair of 625 bearings. v2. I used 6 mr95zz bearings (commonly found in idle wheels on a 3d printer) and tiny m2x16mm to make this version. the dual axles…
Enlarged the mount to add space for a LM2596S Buck Converter
I wanted to use the excellent ERCF Smart Filament Motion Sensor, but I wanted a lower profile, when I mount it to the 2020 extrusion on the back of my Voron 2.4. Therefore I moved the mounting flanges and made the mounting screws M3. I…
ERCF Back-Panel Mounts for Voron This is a clean and sturdy mounting solution for attaching your ERCF (Enraged Rabbit Carrot Feeder) directly to the back panel of a Voron printer. Designed with the signature Voron honeycomb aesthetic,…
I built my FYSETC ERCFv2 kit and used their print files, but when checking the coupler blocks for the ERCT was marked as opaque [o], so following the Voron naming I printed them in black. But then I found out that the coupler blocks are…
This is a bit of a weird one, it actually consists of 2 models overlayed into 1. The step file has 2 bodies and they can't merge for unknown reasons. You'd have to export the main file to print it. I was looking for a flipper version of…
Some brackets to mount everything ontop of your Voron 2.4
Another design for the MK3 LCD cover with klipper logo and ERCF text.
For now only the support arm and the one with BTT MMB supprt has been done, let me know if you need other versions
The ERCF Smart Filament Motion Sensor is neat, and I wanted to mount it on my SV06. To this end, I designed a mount to attach it to the extruder assembly, taking advantage of existing screw holes. I replaced the original 2x countersunk…
These brackets allow you to mount the ERCF on top of your Voron 2.4. They have the perfect angle to mount the ERCF with ERCT buffer, allowing enough space for quite comfortably routing bowden tubes into the Cotton Tail buffer. Three…
As I had some sagging issues on my first print, but didn't want to use auto generated supports, I remixed the original cutter gear to add integrated supports and added self supporting hole to the drive gear
## New changes in Version2 (this version) VS version1 (Version 1 https://www.printables.com/model/971423-ercf-v2-selector-mod-for-larger-28mm-17g-servo * In version1 servo arm cannot touch the filament block top hat to release brake. The…
# ERCF filament Cutter beta7 mod ## What: for ERCF V2 / ERCF Filament Cutter Beta7 https://github.com/kevinakasam/ERCF_Filament_Cutter * it fixed or improved a few problem in the beta7 design * it works with my ERCF V2 28mm servo mod,…
An extra support foot for your ERCF v2 build. This one supports the ERCT buffer and LED Apron. Note you need an extra 16mm SHCS screw, to replace the 8 mm one going through the Support Arm Mount. Category: 3D Printer Accessories
Enraged Carrot Rabbit v1.1 Extruder fitting that sits atop Flashforge AD5M and AD5M Pro extruder to prevent the Bowden tube from popping out during ERCF Filament Changes. Assembly: The Bowden tube slides through from the pneumatic fitting…
Print with no supports, supports are integrated. Use translucent filament for the lens.
Since I am not using microfit connector there was space for a led in the gearbox. No support needed. I have added a removable support. I used a NeoPixel 5050RGBW in the assembly.
Supports A0090 as shown in the picture. The A0090 with silver shell does not need to be modified, just use mg90s
Orbiter2.0 SB model adapted for ERCF toolhead sensor, entry sensor & cutter There are only toolhead sensor version and toolhead&entry sensors version, of which the dual sensor version is 1mm higher and refers to the double step design of…
Voron ERCFV2 top mount Enhanced version Does not affect the sealing
THIS IS A BETA MODEL!! I designed the Servo Mount footprint to match the stationary mount of Filametrix, However, this design choice requires attaching the mount to the extrusion before installing the servo, as there isn't enough…
TowerPro MG90S offers a maximum of ~1.84 kg/cm torque at 5V; the alternative option Savox SH-0255MG offers ~3.4 kg/cm torque at 5V. However, Savox is significantly more expensive. TowerPro MG92B has nearly identical dimensions as…
A link for the coupler blocks and mmu board mount. https://github.com/Tyler8299/CottonTail-Lite
Only modified to use a NEMA17 stepper motor ## BOM: * cnc 60T pulley (2GT, always 2GT type) * one more 20T pulley ( the same type of the ERCF original design for selector motor) * 154mm belt, (2GT close loop) * nylong washer M5 0.5mm…
10/13 Added NEMA14 support. FYI NOT BEEN TESTED. 10/20 UPDATED CALIBRATION INFO 10/21 UPLOADED 5MM TO 5MM COUPLER ERCF2 Direct Drive NEMA17 Mod – Ingeniously Simple, Remarkably Effective Upgrade your ERCF V2 with this direct-drive NEMA17…
I wanted to use all this 3030 extrusion I have lying around so I created a simple mount for the ERCF's 2020 extrusion. 2020 to 3030 mount The “gearbox bottom panel” is replaced with mine “gear_box_bottom_panel_flat”
A standalone filament pre-gate sensor that uses lever switches instead of the more typical ball bearings and switch approach. This sensor can be used both for the ERCF/Tradrack MMUs using Happy Hare, as well as a standalone filament…
A remix of BrokenPoet's amazing mounts, I do not have the room for this setup so I remixed BrokenPoets mounts to mount my ercf on the back of my printer. You do need to use a top feed for the ERCF
Quickly devised model that is in my daily use as mount for ERCFv2 to my Comgrow T300 printer from sovol. Mounted it on 90 degree angle to get the drybox next to the printer. Mount is mounted with standard screws and uses these models…
MENTION: The top PC panel and tape on your printer should be 4mm thick in total or you will have to tweak the model. There's a gap between the top panel and the extrusion, and you can mount your ERCF board using the model: ERCF V2 MMB…
Don't forget to upload pictures of your makes I love seeing your prints of our creations :-)
This mod is to be use with 500mm extrusions that are easier to buy without custom orders. I also gave it more depth inside to grab more of the extrusion and be more steady. This is for the Voron 2.4 350mm version. The extrusion that I…
bom: for each sensor block: 1x 5mm steel ball 1x microswitch without the lever 2x ecas4 couplers without the rubber sealing 1x ws2812 smd led 10mm button 2x 2mm 12mm long screws to hold the microswitch use abs or asa with standard voron…
I keep my ERCF on the side of my Voron 2.4 and the spools are on the table on rollers underneath it. I usually just load filament to the ERCF, and remove it after print, so there is no benefit to roll it to the buffer. This is an ugly…
This is for the right side only, mirror it on your slicer to have the left side.
This is a remixed version of the popular Enraged Rabbit Carrot Feeder smart filament motion sensor, designed for Creality K1 printers and available here on Printables. I have been using it on my K1 and K1M for about six months with no…
I have remixed this corner of the raiser I'm using on my K1 Max to mount my ERCF filament motion sensor remix. There may be some inaccuracies in the hole placement, as I have only printed it once and have been using it since then. The…
UPDATE: The original cover was not working reliably enough, so I simply extended the original apron LED cover to a 8N version. The original version will still be available, but I recommend the more sturdy one. The pictures are still from…
Please refer to the original for instructions, and this is just a refined and cleaned up model for the filament path. but these are the key improvements I did the the model. Key upgrades:- Slug cleaned up and made a bit tighter, with…
Mount for the Enraged Rabbit Cotton Tail (ERCT) for the EasyBrd
This is a mount for a bigger MG996R servo for Enraged Rabbit Filametrix. What do you need: - 5 M3 heat inserts - 4 M3 x 16 screws - 1 M3 x 20 screw - 1 M3 nut - 1 M3 x 16 BHCS screw
This model is for the 2 sensor version with the btt ebb rb2040 and ERCF filament cutter.
To color the logo you'll need to split-to-parts the stl once opened. Two sizes, one (20mm) spans over the 2020 extrusions, so the length needed is the same as the front brace 2020 on the printer (depends on printer size of course). The…
ERCF v2 No logos and Molex holes, Bottom panel Straight mount For the next project we needed clean and flat surfaces. The cables were routed straight to the ERB board, without any connectors between them. Here are only the parts where the…
Easily identify which PTFE tube is coupled to which input of your MMU2S or ERCF. The included STLs have the base component and 2 number parts included. Important: Use the Split → To Parts function (once the part STL has been imported and…
300mm remix with reinforced 2020 rail mounts. Edit 2025-02-03: -added step file for 2020 mounts -added 2020 mount models in 3mf with 0.5 and 1mm larger tolerances for the 2020 extrusion by request. (Untested) -added 2020 mount tolerance…
Created a Magnetic Release 12 Gate Catch Tray for the ERCF Cutter. Held in place onto a 2020 Rail for the ERCFv2 to catch the cuttings. Requires 12 3x6mm Magnets to hold into place 3x t nuts and 3 M3x6mm bolts
ERCF Remote electronics panel. Couldn't find a nice panel to mount both MMB boards for my 12 gate ERCF. And didnt want them separated on different panels, so used the BTT Templates and built the design. Panel accommodates for mounting the…
This is a longer rear mount for the BTT MMB for the ERCFv2 it is about 20mm longer so that you can still mount it when using longer gate blocks with pre-gate sensors like these . I exported the mount in question from Fusion (which I am…
I designed these mounts for the ERCF and Filamentalist setup I've been using lately after running into some conflicting geometry with the original magnetic panels design by Le0n. I've integrated the same magnet spacing into the corners of…
This standoff can be used to mount 2020 aluminum extrusions on top of a Voron printer. For assembly, you will need (per standoff): 1x DIN912 M5 35mm 1x DIN7380 M6 16mm / DIN7380 M5 16mm (depending on the inner diameter of your 2020…
Brackets to mount extrusions on top of a Voron. Mostly for mounting an ERCF, but you do you :) Really didn't see the point to have text on them, especially if its wrong. Those Brackets work just as well on any Voron, no matter the size.…
EREC for ERCF1 - bearing version 623 and V623 EREC - Magnetic Cover for Cutting Arm here .
This extends extends the original Filament_Path_xN.stl included with ERCF v2 to create room for an entry sensor. The tag is relocated to the front of the the tube so it will remain visible and the latch is narrowed to clear the extended…
My cheap ecas connectors kept breaking in use on my ERCF. I only had M6 PG4 connectors so I modified the cutter arm to use those.
The standard geared drive for the ERCF V2 over complicated it for me. And the 188mm GT2 belt is notoriously difficult to find in South Africa, also did not want to pay a dollar or two for the belt and $50 plus for transport. I also tried…
not much more to say, I made them taller because I used to have the spool feeds coming from the front under it and I made the mounting screws a little easier to get to
Printer: Voron Trident 300 Filament: ASA C-tech Premium-line BLACK Printer settings: Hotend temperature: 255 °C Bed temperature: 110 °C Layer height: 0.2mm Infill: 40% honeycomb Supports: No Brim: No Other settings are the same as on…
After I finished my Ercf v2 build I was immediately annoyed by the Cottentail buffer system, way too difficult to load and way too much drag. I modified the coupler blocks so they run in a straight line and kept other original features…
I wanted to provide a 3.3V pin input to the ERCF v1.1 microfit connector, so I modified the existing design to accommodate a Molex MicroFit 3.0 6-pin connector instead of the original 5-pin connector.
This is a preparation for cutting 8mm bars for e.g. ERCF. They are suitable for vice jaws with standard dimensions of 10
Standard block from ERCF v2 (aka Triple Decky C7) with a sensor. Requires a 4mm ball bearing and a D2F-01FL endstop switch, exactly the same as in https://www.printables.com/model/651002-k1-extruder-filament-runout-sensor . If you…
I really like the original design. But my ERCF is not mounted on a Voron so I shortened the legs for a general design.
A new design of the mount for ERCF. Use this instead of https://www.printables.com/model/920702-creality-k1-max-ercf-top-mount , if your lid riser interferes with it, or if you need better access to the lid. The provided model is for the…
This version of the Afterburner Galileo extruder accommodates a 7mm ball bearing and microswitch to detect filament after the extruder gears as required by the Enraged Rabbit Carrot Feeder as a filament sensor. Can be printed in ABS+ or…
Support Arm Endcap With MMB V2.0 For ERCFV2's mod ERCT Buffer Support MMB V1 & V2
With the holder you can attach your ERCF to the 3030 profile You need: 4x m6 T-slot 4x m6x12 4x m3 nut 4x m3x12
Same model as @ntchris uploaded but modified for heat inserts instead of hex and square nuts. Also added a modified mid mount for those not use the stock exhaust option and instead using this…
Description Clean up the cables around your ERCF drag chain! 2x3pins : You'll find the files for a standard ERCF where you need 6 pins, 3 for the encoder, 3 for the servo. 2x5pins : Then there is a version if you have the status LED or…
I have built an ERCF for my K1 Max and this allows for aluminium extrusions to be fixed across the top middle of the printer as I don't have enough space to mount it at the rear. For the K1 Max you will want 2x 2020 Aluminium extrusions…
Here Are you seeing , an Gantry Servo Depressor for the Filametrix or the FilamAtrix. This Servo Depressor works with the normal Filametrix or FilamAtrix (CW2 and G2E) Material are needed: 1 x M3 Heatnut 1 x M3 4x3x5 Heatinsert (short…
ERCFv2 Mount for Voron 2.4 DOOMCUBE printers. This mount should also work with standard V2.4 printers. This is installed along the Z extrusions on one side, and mounts 2x 2020 extrusions which mount to the feet of the ERCF. Printed with…
This is the Support Arm Endcap for the Enraged Rabbit Cottontail Buffer for the ERCF v2 remixed to accept a BTT MMB CAN v2.0. The only change from the original v2 assembly instructions is the addition of two more m3 heat set inserts.
This mod is currently in beta testing and is still undergoing refinement. Use it at your own discretion. I take no responsibility for any damage caused to your unit during installation or operation.
I needed a modified version for a 8 channel ERCF so I just made them a little sorter.
It is the same as original (see https://www.printables.com/model/1053284-standalone-filament-sensor-happy-hare-ercf-tradrac ), just for different lever version. I like the bigger arc of D2F-L30 more.
I dislike how unstable the standard ERCF feet are when mounted onto 2020 extrusions and the adjustable mount is just way overkill. So I added larger feet to the existing parts. Things are angled appropriately so no supports necessary.…
Cyberstyle filament sensor from ERCF. Need 5.5mm steel ball + 2x M2X10 + ECAS / PC-M5+ Omron D2F endswitch.
Redesigned these nice ERCF legs. There are two versions: ercf_leg_universal has a through-hole, so any 2020 extrusions longer than the printer can be used. In case you have an error in extrusions length or don't want to cut them.…
