CNC X-Carriage Add-On Parts for VORON Stealthburner (Vitalii3D)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
X-Endstop and PCB Klicky mount with sleek cable management for the VoronLightweightXCarriage - of course with style. 😎
- Ocena
- 0 / 5
- Polubienia
- 18
- Pobrania
- 2420
- Wydruki
- 0
- Wyświetlenia
- 4142
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- GNU General Public License v3.0
The VoronLightweightXCarriage by Vitalii3D 🥰 is a fantastic lightweight carriage for the Stealthburner but I was not happy with the existing cable management solution for a ClockWork 2 setup. So, time to make some parts.
The Features
A clean X-endstop solution
A matching PCB Klicky mount
Sleek cable management guiding the cables into your CW2
... all of course with a little bit of style 🤩
![]()
|
Depending on your specific setup (e.g. XY joints, installed mods, X-probing configuration, or any CNC/X-Beam upgrades), the Cable Guide part may contact the XY joints before the X-endstop triggers, preventing X from homing correctly. Check that your X-Endstop can trigger before X-homing your Voron! In the rare case that your run into this issue, I have two options for you:
And for the very brave of you: I left the initial model in with full cable cover: The Cable Guide MAX. If you try it, be warned, chances are high that it effects your X-homing. |
Companion Models for SB2209 / 2240 Based Toolheads: |
|---|
![]()
Cable Bridge PLUS for SB2209 / SB2240 Refined cable bridge for SB2209/SB2240 with PG7 gland, stepper cable cover and steel wire mount - sleek and compact. |
![]()
XT30 2+2 Plug for SB2209 / SB2240 Compact XT30 2+2 plug for BTT SB2209/SB2240 toolhead boards with minimal footprint for clean cable management. |
Compatibility & Requirements
Designed as add-on parts for the VoronLightweightXCarriage by Vitalii3D
Requires relatively small cable diameter (AWG24, tested with pre-crimped JST PB silicone cables used for BTT EBB 2209 CAN V1.0)
Assembly
Just follow the pics (the red part will help inserting the heat set inserts - tough to get out at the end but heat set inserts will be placed precisely 📐.
![]() | ![]() | ![]() | ![]() | ![]() |
|---|
![]() | ![]() | ![]() | ![]() | ![]() |
|---|
![]() | ![]() | ![]() | ![]() |
|---|
![]() | ![]() | ![]() | ![]() |
|---|
Printing
Material: ABS, ASA, PC-CF or similar. The PCB Klicky mount is designed as slim as "acceptable", so make sure you use some material that does not flex or deform under heat.
Settings: Just use your standard VORON print settings, no supports required.
BOM
Cable Guide: M3x5mm SHC (1 pcs)
PCB Klicky Mount: M3x6mm BHC/SHC (2pcs)
X-Endstop Mount: M3x6mm SHC (2pcs)
X-Endstop OMORN switch mounting options:
M2 x 10 Self-Tapping Screws (2pcs)
M2 x 4 x 3.6mm Heat Set Inserts, M2 x 8mm SHC (2pcs)




















