181 modeli
This mount raises the PG7 so you don't have a large “S” loop when using the smaller mounts. This design was provided by Nyxcode on Voron discord. Enjoy
[English] I used the chain anchor 2hole design, closed the hole at the tip and enlarged the anchor a bit because I didn't like the designs or the just didn't fit. It includes a M12x1.5 thread to be able to attach a PG7 cable gland. Just…
I print big things and the thought of wasting filament and time because suddenly, in the middle of the night, the filament runs out, is not something I am fond of. So I created a simple filament sensor mod for Voron's CW2 (RC1), using a…
Adapter allowing DeWalt's DCW210B sander (or any other tool compatible with the DWV9000 adapter) to a Festool 27mm dust extractor hose, with or without the twist-lock mechanisms each connector allows. Updates: 2025-09-21 Increase…
V1.1 - UPDATE: As @Hornet331_645553 noticed and mentioned, there was a slight misalignment with the lower sensor. I have implemented a fix for it as well as added slightly more clearance for the upper D2F switch, hopefully making it…
On my Voron 2.4r2 i have an BTT EBB36 v1.2 installed. Since the board is mounted on the back of the LDO Nema 14 stepper behind a ClockWork 2 the cables came extremely close to the drag chain when homing. Also the wires were exposed on the…
Added vents
This is a rigid mount for the BTT EBB3.6 v1.2 toolhead board on the ClockWork2 / Stealthburner. The plate is supported on three points and a lot more rigid than other solutions. It was only tested on a Voron Trident. No tests currently on…
Simple M12x1,5 Cable Holder for Umbilical with Can-Bus. BOM: 1x M3x20 SHCS 1x M3x8 SHCS 2x Heat-Set Insert M3x5x4
Background After switching my Trident over to using a CAN toolhead and removing the X/Y cable chains, the one thing that I wasn't satisfied with was umbilical wire management. Unlike on the Voron 2.4, piano wire isn't very practical since…
Discussion Update 25 June 2024 The lower filament path is designed for a PTFE tube with a 3mm ID/4mm OD. Chamfer the end next the gears. This will provide a large target for the filament as it exits the extruder drive gears. Update V2.6:…
Different take on CANbus cable strain relief using PG7 Gland. Intended for newer BTT Toolhead boards with thicker connector. For those who want lower and centered mount. Although routing the cable is a bit finicky. Added cutout version,…
Substituted the 5010 part blower with a much more powered WS7040 blower
My update filament sensor before and after the extruder for ERCF Rabbit Feeder. 2x sensor D2F-5 2x ball 5,5mm 4x tapping screw M2x10
Introducing the “anorexic” ClockWork 2 aka SKELETONIZED CW2. Lighten up your heavy StealthBurner Tool Head. Use PIF Standards for printing. Preferably ABS, ASA or tougher material. Layer height: 0.2mm Extrusion width: 0.4mm, forced Infill…
Wall mount for DeWalt DCW210 20v random orbit sander
CW2 Main body for use with the BTT EBB SB2209/RP2040 canbus toolhead board. Dual filament sensors for use with the ERCF. Updated 9/23/25 New and improved EBB fan housing, way more room and improved air flow. Fixed the tight limit switch…
Nice feature No need to disassemble the wire harness to install this gland. Bill of Materials Category Qty Description Notes Hardware 3 M3 heat insert Voron BOM Hardware 2 M3x10 SHCS
This is my take on EBB36 canbus board holder for Voron Stealthburner. I have taken the model from Kotvic (Thank you!) and pretty much redesigned it to address some issues I have found with the original model: Heat inserts holes were too…
Remixed Stealthburner CW2 chain anchor for PG7 mount
closed cable hole on top added 30x30 fan with mouning holes Now nicely closing all cables with the EBB36 mod on Stealthburner.
Just a simple mount for a PG7 - fits CW2 Used it with the BTT EBB 2209/2240. May fit other boards aswell. 1x heat set insert (Standard Voron) and 2x M3x8 SHCS needed.
Use with the CW2 cable bridge.stl from BTT. Too big to work with the regular cable cover so i added a cutout. You'll have to print it with supports. Add two M3 heat-set inserts into the clamp. Secure with M3x16 screws (or longer, but they…
Same setings as Voron parts. It needs supports for print!
BETA The printhead brackets supplied at Github allows for pressure fit around the neck. However there is a tiny bit of wiggle in this mount but the Aliexpress version also allows for removal of the neck to expose M2.5 bolt holes. These…
Forget flimsy CAN wires free flying around your Voron's enclosure. This is the mod solving the issue the way Bambu Labs X1 does it. Check this mod in action here: Recommended print settings Extrusion width: 0.4mm, forced Layer height:…
Remix to add a drag chain mount. For Switchwire with EBB SB2240_2209 CAN bus adapter, specifically to allow a drag chain for use with Beacon bed probe rather than umbilical. This is a new mix that has not been tested yet! There are two…
Dewalt DCW210 Cordless Sander to Festool Cleantec Adapter This adapter allows a Festool Cleantec dust extractor to be used with the Dewalt Cordless sander (O-Ring also required). This sander is generally a good design with the exception…
This model is modified from KayosMaker canboard mount https://github.com/KayosMaker/CANboard_Mounts It is design specialised for mounting BTT EBB36 canbus board on Voron Stealburner CW2 and can still use dragchain for cable management…
Updated the design to work with the “twirl” version of the HGX gears. Support is needed for the pocket that the motor sits in. Print quality is on par with Galileo 2 or better Twirl gear:…
Remix to support a 2 hole drag chain. Update: Seems like the original 3 hole and the 2 hole remix did not work. I made a new version that's been tested now and works well. I did desolder, flip, then resolder the hot end heater connectors…
Forget about the thin wires flying freely around the body of your Voron. This mod solves the problem the way Bambu Labs X1 does. The mod includes all the files needed for assembly and installation. Recommended print settings Extrusion…
My update filament sensor before and after the extruder for ERCF Rabbit Feeder with filametrix cutting mod from the GitHub user sorted01 https://github.com/sorted01/Filametrix 2x sensor D2F-5 2x ball 5,5mm 4x tapping screw M2x10
Could not make any existing vacuum hose adapters work so I modeled up in Tinkercad a adapter. This connects my my Dewalt DCW210 to a 1 7/8" vacuum hose (coming from my Ryobi vacuum) Print Settings Printer: Ankermake M5 Rafts: No Supports:…
Add a ECAS mount to the CW2 with filament sensor mod to meet requirment of MMU system. This is a remix. You will need a modified lever for this extruder in the original project.
This is a modified version from BTT Cable Bridge part. There are a bunch of flaws in the design that I corrected, notably the heat sets are angled on the original part and locations are not optimized to work with an official Voron…
Simple wall holder
I'm using Galileo for past two years, now converted to Orbiter 1.5 to more compatibility, but no found a step file with CW2 support but some to 2.0… This is based on the best I've found(IMO).
Main body update with reinforced latch from - https://github.com/VoronDesign/Voron-Stealthburner/tree/main/STLs/Clockwork2/Direct_Drive !! NOT PRINTED AND TESTED !! - I created at the request of another member. For assembly: 2x sensor…
A total re-design of my bowden version which was a remix this model was designed from scratch using the same dimensions but cutting out more material for clearance. I've also added a heatset hole in the side for the original neptune…
ENDER 3 STEALTHBURNER CW2 CR TOUCH MOUNT FOR MGN12 (v1.6) This is a remix of Stealburner and Clockwork 2 Mount for Ender 3 With MGN12 Rail You'll need a few things to make this work: (10) M3 x 4 heat set inserts (2) M3 x 40 mm cap head…
I added a magnet in the guidler which pulls the ball away from the microswitch, preventing false positives. The CW2 body is also modified to accommodate the magnet. There are also some minor printability improvements in the ball cavity.…
Different take on CANbus cable strain relief using PG7 Gland. Intended for newer BTT Toolhead boards with thicker connector. For those who want lower and centered mount with a cutout for the cable/screw in portion. Make sure to route the…
Modified the guard to improve the support of the cable harness
A quick and dirty tweak of therick's WWG2 NH36/EBB36 PUG mount https://www.printables.com/model/968109-wwg2-nh36ebb36-pug-mount to make it fit with a Clockwork 2 extruder. The original PUG download page (for the gland itself) is at…
Sleletonized CW2 inpired by @PowenChi_1306772 versions of the cw2, but made from scatch using the original newest motor plate and the filament sensor version of cw2 linked as remix. The Stealthburner on the picture is this one. I might…
I needed a way to connect my shopvac camlock system to my dewalt sander - so instead of using a variation of adapters, I decided to remix these two. Use the print instructions @exnerd gives on his page
the files like pg9.2.2 doesn't mean anything its a rev number for me since i had to redo it a few time to get it right.
Little adapter plate to hold a Voron afterburner PCB on the new Clockwork 2/stealthburner. I designed it to tide me over until I get one of the new stealthburner pcbs. I used some little Bass m3 standoffs to prop the PCB off the surface…
I remixed the original to allow a Mellow Fly SH-36v2 CANBUS board to mount on the Voron Clockworks2 Stealthburner I've also made the umbilical mount a bit ticker and longer to allow for better mounting with colson-ties
Simple M12 Thread Mount For Attaching A Cable Gland To The Back Of CW2
For ERCF v2: Clockwork2 body (new Version) modified incl BigTreetech EBB v1.2, Toolheadsenor, Entrysensor, ECAS and Filamentrix Cutter for ERCF v2 included: BTT EBB v1.2 STLs Latch (new version) slicing with prusa/orca slicer works well.…
In the original model the lower switch recess was slightly to shallow, the switch was standing out.
Voron Trident Power inlet CW2B
EBB36 mount for Voron Stealthburner (CW2) with Thread 12MM
This design allows the EBB36 CANBUS board to be used on Stealthburner with CW2 while retaining the X axis cable chains. A few items of note: You must use the ‘PCB’ cable cover door on Stealthburner. The backpack bracket includes built-in…
I frequently has issues with the BMG idler popping out of the guilder arm in the CW2 extruder. This issue seems to happen to others as well, see for example this message in the Voron discord. To hopefully fix this issue I remixed the…
The ercf’s tool head sensor with ECAS 9/19 Update step file Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Other ABS Black Category: 3D Printer Extruders
Instructions: Print. Outline = 2, 30% infill should be fine Insert heatset 3mm threaded inserts Bolt on 3010 fan with 3mm bolts of your choice Install on CW2 Connect fan to power source REMEMBER to redo your acceleration compensation…
Use all the same parts from nzalog's remix and replace the 2 hole with 3 hole.
The original stubby mount for an M12 cable gland has an M12x1.75mm pitch. The CNLinko connectors have M12x1.25mm pitch so I re-modelled the mount to have an M12x1.25 thread. CNLinko waterproof connectors in various pin configurations can…
Remix of Wissencat's Meowburner, The Puurrfect Stealthburner (Which is awesome) mixed with https://github.com/EtteGit/EnragedRabbitProject/tree/main/usermods/CW2_with_ECAS_and_optional_sensor by GarthSnyder to use ECAS as well as…
Here Are you seeing , an Gantry Servo Depressor for the Filametrix or the FilamAtrix. This Servo Depressor works with the normal Filametrix or FilamAtrix (CW2 and G2E) Material are needed: 1 x M3 Heatnut 1 x M3 4x3x5 Heatinsert (short…
Remixed to fit different extruder frame (with angle cut at the botton)
This remix is for common 3 hole cable chain whit heat set insert.
A mod of the Voron Design Stealthburner and Clockwork 2 extruder designed to suit the Bondtech LGX lite / LGX Lite V2 extruder and Mellow SB2040V3 Canbus board. The Mellow SB2040V3 is quite different to the V2 designs and uses a new…
Printed from PLA upright. there were no issues with support. Printed with X1C
The purpose for these adapters was initially for me to use some extra Creality Sprite extruders I had laying around and put them in some Stealthburners as they are honestly pretty decent extruders (if you grease the gears and replace the…
Voron Stealthburner CW2 chain extension for non IGUS chains like from Formbot kit. Use M3x16 for 10mm or M3x20 for 15mm extension block.
Main body update with reinforced latch from - https://github.com/VoronDesign/Voron-Stealthburner/tree/main/STLs/Clockwork2/Direct_Drive !! NOT PRINTED AND TESTED !! - I created at the request of another member. For assembly: 2x sensor…
ECAS PTFE tube connector added to Voron Stealthburner for use with BigTreeTech SB2209 I have adapted main_body, latch and cable_cover from Voron Stealthburner for BigTreeTech SB2209 USB. It may also be compatible with SB2209 CAN.…
Print this in ABS only, using Voron printing guidelines. No supports needed. Tested only on Voron Trident, but should be compatible with 2.4. Use the second part (black piece in the picture that clamps onto the PUG) from the original to…
Rockler's Dust Right FlexiPort Dust Canister comes with the usual assortment of FlexiPort connectors but none of them fit well with the connector DeWalt uses on its tools, specifically the DCW210B sander (but actually any tool compatible…
Hi I just made this runout sensor for the clockwork 2 work with a 6mm airsoft BB. Since I didn't have a 5.5mm steel ball laying around, but a ton of 6mm BBs, I chose to make it work with a 6mm ball. I have tested it, and it works fine…
A remix of https://www.printables.com/model/747487-clockwork-2-mounting-arm-for-pug-umbilical to make it slightly more compact so that the PUG doesn't foul against umbilical cables that use a right-angled connector on the toolhead board,…
build is exactly same as cw2. Knomi V1 untouchable is tested and is working fine, it should also be compatible with knomi v2 but it is not yet tested.
Voron CW2 Carrier with Klicky, endstop Holder, a cover for the Screws and more air that can go thru
Bau und Programmieranleitung gibt es auf Youtube #### Neu #### Upgrade Dateien aus dem Video
Download the updated version below: Filament runout sensor for Stealthburner with EBB SB2209
I purchased both the NiteCORE CW20 and the WolfBOX MF100. The NiteCORE quality is leaps and bounds better although slightly less powerful / cfm. I modeled the 12mm tip after the WolfBOX and still wasn't as happy, so I remixed the 10.5mm…
This design requires a different latch ( https://github.com/EtteGit/EnragedRabbitProject/blob/main/usermods/CW2_with_ECAS_and_optional_sensor/STL/%5Ba%5D_latch.stl ) and a different cover door like (…
I could not find a cable door for Filametrix Stealthburner CW2 with ECAS, so i modified the Cable door from BTT
A modified CW2 body that takes both sensors, but uses a PC4-M6 BSP connector
This uses the usual KW10/KW11/D2F size switches. Re-made X carriage endstop mod for the v2.4r1 + cw2 mount on mgn9 because the one I found at https://www.printables.com/model/662739-voron-mgn9-endstop-carriage-cw2 does not have holes that…
the Large Gear Clockwork 2 by nhchiu has slight different hole spacing for the drag chain mount, so I addapted the CW2 mounting arm for the PUG by cliftoce to be able to mount the PUG by fbeauKmi on the Large Gear Clockwork2. only the…
I updated the ERCF CW2 main body with sensor and ECAS fitting to use the upgraded latch. I wanted to have ears on my SB so I merged Meowburner with the ERCF CW2 main body and upgraded the latch system while I was at it, I figured it would…
Added an ECAS connector
Hi, this is the Chamber Thermistor holder I use on my own LDO Rev. C Voron 2.4r2. I didn't like to see the Chamber thermistor the way the LDO holder attaches, so I designed this from the LDO .f3d file, and like how it works much better.…
remix of: https://www.printables.com/de/model/463220-voron-cw2-stealthburner-ebb-sb2240-pg7-umbilical-m thanks for the initial work! to fit plug: https://aliexpress.com/item/4001153106923.html and wire harness of one mellow Fly-SB2040…
What changes compared to the original: In this mod. the sphere was replaced with a 6 X 3 magnet to make the contact on the filament sensor microswitch more reliable for the new Filamentrix CW2 version and added ECAS mount. The .zip file…
These toolhead boards get hot, crazy hot, especially the BTT SB2209 RP2040. Before it burns up I decided to add active cooling. I initially made one with a 3010 fan which took the temp down to ~65-70 depending on print time which doesn't…
Insert nuts used with Voron and filament sensor parts used with Prusa mk3s are required. I will also upload the unprocessed version of nema17's remix. I don't have a nema14 motor, so I haven't tested whether it can be used. CAUTION You…
* NEW VERSION - https://www.printables.com/model/1064760-neptune-4-and-4-pro-stealthburner-with-beaconcarto * Mounting plate for StealthBurner for Elegoo Neptune 4 with mounting holes for beacon3d or cartographer probe or original…
Modified to work with 6.3mm balls i got from an old bike bearing. The original description also says that it's not compatible with original hotend mounts, but that's what I'm using and it works so idk.
Es werden noch 2 Schlosserscheiben für M3 und eine M3x30mm DIN912 benötigt. Die zwei Schlosserscheiben werden mit einem leichten Fett oder Ölfilm belegt und zwischen Halter und Fahne montiert um ein reiben von Kunststoff auf Kunststoff zu…
I wanted a pg7 mount to route the cable out behind the stealthburner, horizontally centered on an enderwire (switchwire) build. The pg7 cable does not run into the vertical extrusion on either side and is a decent route to push the…
You only need 2 short M3 fusible nuts and 2 5mm M3 screws. PETG is sufficient for the print.
This is a wall mount for a Dewalt DCW210B brushless cordless random orbital sander. This works with the US version of the sander. It mounts to a wall using 2x #8 wood screws. I have included the Fusion and Step files in case you want to…
Voron MGN9 Carriage with X-Endstop for CW2
