1 / 13
X-Max 3 Endrborinn Toolhead - A4T Dragon + Sherpa Mini Assembly — zdjęcie 1
1 / 13

X-Max 3 Endrborinn Toolhead - A4T Dragon + Sherpa Mini Assembly

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

An updated front half of the STOCK X-Max 3 toolhead to accommodate the A4T Sherpa Mini+Phaetus Dragon UHF. EASY UPGRADE!

Ocena
0 / 5
Polubienia
7
Pobrania
9
Wydruki
0
Wyświetlenia
198
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

X-Max 3 Endrborinn

A4T Dragon UHF + Sherpa Mini Toolhead

Endrborinn — “reborn / born anew.”

Introducing the Völund Forge X-Max 3 Endrborinn, a redesigned QIDI X-Max 3 toolhead built around the A4T platform, Phaetus Dragon UHF, and Sherpa Mini.

Endrborinn was designed around one primary goal: upgrade the X-Max 3 toolhead while making installation as simple as possible.

Instead of replacing everything, the design retains the stock rear clamshell, toolhead board and wiring, X-axis rods, and belts. The entire front half of the original clamshell is removed and replaced with the Endrborinn front clamshell and A4T assembly.

The best part?

You don’t have to mess with the belts.

Update: 8/3/26

  • The toolhead centering is fine. The X-Max 3 Endrborinn Toolhead - A4T Backplate is width matched to the A4T cowl. The A4T cowl is hard to match, but that is the root of the weird spacing that I though was a shift in the toolhead. Anyway, no need to panic, I'll address the width so it's even and I can rest my OCD. Zero issues.

  • I've amended the Z height of the X-Max 3 Endrborinn Toolhead - Beacon + Cartographer mount. It now places the beacon coil at 2.6mm instead of 2.75mm. I've also marked orientation of the mount so that the odd spacing will not look bad. It will work perfectly fine in any orientation, it is just a visual issue as hole spacing and mount position are unaffected.

  • All relevant files are updated.

Update: 8/1/26

  • I have found that at some point, the entire toolhead has shifted less than .1mm to the left as viewed front to back. I will correct this shift, but in the meantime it should not affect the performance of the toolhead at all. 

  • Revised X-Max 3 Endrborinn Toolhead - Beacon + Cartographer mount.

    • Eliminated the center cutout due to flimsiness when tightening. It's now a solid piece.

    • Corrected spacing and added text to denote mounting direction.

Update: 7/31/26:

  • Revised X-Max 3 Endrborinn Toolhead - A4T Backplate & X-Max 3 Endrborinn Toolhead - Beacon + Cartographer mount.

    • Corrected some spacing for the bottom probe mount heatserts. 

    • Added a Ghost Face version to the X-Max 3 Endrborinn Toolhead - A4T Backplate in order to remove some material and add a passthrough for toolhead wiring.

    • Updated X-Max 3 Endrborinn Toolhead - A4T Dragon + Sherpa Mini Assembly with updated parts.

  • Added a short hardware BOM

Initial Release: 7/30/26

⚠ BETA RELEASE

Endrborinn is currently a BETA design.

I’ve reached the point where I feel the design is safe and complete enough to release for public testing, but that does not mean every issue has been found.

The assembly has been extensively modeled and checked in CAD, but real-world testing may reveal tolerance issues, interference, hardware combinations, or other problems that I haven’t encountered yet.

If you’re installing this toolhead, expect that some troubleshooting, adjustment, modification, or reprinting may be necessary.

Comments, suggestions, testing results, and criticism are absolutely encouraged.

If you run into something, let me know. The whole point of releasing the beta is to get more machines running it and improve the design.

Remix to your heart's content! I'd love to see what you do with this idea!

Design

Endrborinn started with the A4T Dragon/Sherpa Mini toolhead and evolved from there into a new front assembly specifically for the X-Max 3.

The following stock X-Max 3 components are retained:

  • Rear toolhead clamshell

  • X-axis rods

  • Belts

The stock front clamshell is not reused.

Remove it, put it somewhere safe, and forget about it unless you decide to return the machine to stock.

Stock Nozzle Position

One of the most important design goals was maintaining the original X-Max 3 nozzle position.

According to my CAD models, the Phaetus Dragon UHF nozzle tip is located in the exact same X, Y, and Z position as the stock X-Max 3 nozzle tip, or as close as the accuracy of the reference models allows.

This should minimize changes to the machine’s existing geometry and make the conversion significantly easier.

That said, verify everything on your own machine before printing. CAD is CAD and reality is reality.

A4T Compatibility

Although Endrborinn was designed and tested around the Dragon UHF + Sherpa Mini A4T, I am fairly confident that other A4T configurations can be used.

The primary thing you need to watch is nozzle position, particularly Z height.

I don’t currently know exactly how much farther above the build plate an alternative A4T configuration can place the nozzle before modifications become necessary.

A longer hotend should generally be less problematic, provided your Beacon or Cartographer mounting height and calibration remain appropriate.

If you experiment with another A4T configuration, carefully verify:

  • Nozzle Z position

  • Probe-to-nozzle height

  • Hotend clearance

  • Extruder clearance

  • Fan/duct clearance

  • Wiring clearance

  • Rod and belt clearance

  • Full X/Y travel

If you successfully run another configuration, please send me the details so it can be added to the list of confirmed combinations.

Probe Compatibility

Endrborinn is designed for:

Beacon or Cartographer

Use whichever you prefer. Different revisions should not present a significant issue as long as the mounting requirements are compatible.

The stock X-Max 3 inductive probe is NOT supported.

Beacon Mounting Location

X: 0 mm
Y: -20 mm
Z: 2.6 mm

These dimensions describe the designed mounting relationship. You are still responsible for correctly installing, configuring, and calibrating your probe.

Do not blindly copy Z settings or offsets without verifying them on your machine.

Required Parts

Endrborinn Hardware (incomplete)

  • 12× standard Voron M3 heat-set inserts

  • 6× M3 nuts

  • Probe mount - 2x 12mm-15mm M3 FLAT HEAD screws. Beveled/BHCS/SHCS will interfere and contact the plate.

  • A4T->Backplate - 4x 50mm M3 screws*

  • Rear Clamshell->Backplate

    • Lower Holes - 2x 30mm M3 screws*

    • Lower Middle Holes - 2x 28mm M3 screws*

  • Rear Clamshell->Front Clamshell

    • Upper Middle Holes - 2x 10mm M3 screws*

    • Top Middle Holes - 2x 14mm M3 screws* **

    • Top Outer Holes - 2x 8mm-10mm M3 screws* **

  • Front Clamshell Rear->A4T

    • Center Holes in the old extruder motor opening - 2x 16mm M3 screws* **

*BHCS preferred, although SHCS or other appropriate M3 hardware can be used

**Uses M3 nuts

Screw lengths are approximate and should be checked for clearance and interference during assembly. When determining screw length, remember that the stock rear clamshell is part of the assembled stack-up. Do not select screw lengths based only on the printed Endrborinn components.

A4T Hardware

You’ll also need all hardware required by your chosen A4T configuration, including:

  • Fans

  • LEDs, if desired

  • Fasteners

  • Heat-set inserts

  • Any other A4T-specific hardware

For the A4T side of the assembly, refer to the official A4T BOM and installation documentation.

Hotend

Phaetus Dragon UHF

  • 90 W maximum heater

  • Cartridge-style K500 thermocouple sized for the Dragon heater block

TriangleLab sells a compatible cartridge-style K500 thermocouple.

Extruder

Sherpa Mini

Probe

  • Beacon, or

  • Cartographer

Hardware Locations

The included reference photos identify the Endrborinn-specific hardware locations:

🔴 RED — Heat-set Inserts

Install ALL marked heat-set inserts before beginning toolhead installation.

These use standard Voron-style M3 heat-set inserts.

🔵 BLUE — M3 Nuts

These locations use captured M3 nuts.

🟢 GREEN — Rear Clamshell Screws

These indicate screw locations passing through or attaching through the stock rear clamshell.

Again, take the thickness of the stock rear clamshell into consideration when selecting screw lengths.

For hardware associated specifically with the A4T assembly, refer to the official A4T BOM and installation guide.

Basic Installation

A more detailed installation guide will be added as the beta progresses, but installation is relatively straightforward.

  1. Remove the stock front toolhead clamshell while retaining the rear clamshell, rods, and belts.

  2. Install all required heat-set inserts and captured M3 nuts into the Endrborinn printed components.

  3. Install the new Endrborinn front clamshell using the appropriate M3 hardware.

  4. Install the A4T backplate using the appropriate hardware.

  5. Assemble your A4T toolhead with the Dragon UHF, Sherpa Mini, fans, thermocouple, heater, and associated hardware.

  6. Terminate the electrical leads appropriately for use with the stock X-Max 3 toolhead board.

  7. Install the completed A4T assembly onto the backplate.

  8. Install your Beacon or Cartographer probe.

  9. Before powering heaters or commanding full-speed movement, manually verify toolhead clearance throughout the machine’s usable travel.

  10. Configure and calibrate your probe, verify your heater and thermocouple operation, and confirm all Klipper safety limits before printing.

That’s it.

If you’re an X-Max 3 owner, there’s a good chance you’ve already had the stock toolhead apart more times than you’d care to admit. Endrborinn was intentionally designed to make the mechanical side of this conversion relatively painless.

And again:

No belt disassembly required.

Tested Configuration

The current Endrborinn configuration is:

Printer: QIDI X-Max 3
Toolhead: Völund Forge Endrborinn
Hotend: Phaetus Dragon UHF
Extruder: Sherpa Mini
Probe: Beacon / Cartographer
Rear Clamshell: Stock QIDI X-Max 3
Rods & Belts: Stock QIDI X-Max 3
Temperature Sensor: Cartridge-style K500 thermocouple
Heater: Up to 90 W
Cooling: A4T configuration

Other A4T combinations should be considered experimental until confirmed.

Before You Print

Remember that this is a beta release.

Before running the machine, verify:

  • Nozzle position and usable Z range

  • Probe position and calibration

  • Probe-to-nozzle relationship

  • Heater operation

  • Thermocouple operation

  • Hotend and extruder mounting

  • Fan operation and clearance

  • Wiring and strain relief

  • Belt and rod clearance

  • Full X/Y toolhead travel

  • Klipper temperature limits and safety configuration

Use this design at your own risk.

If you discover a problem, please report it. Fitment reports, alternative A4T configurations, photos, suggestions, and other feedback are extremely useful while Endrborinn remains in beta.

Future plans

As I complete this setup, more will be added. I would like to add the different extruder and hotend combinations available with the A4T setup and retain the stock nozzle position. After that, A5T and beyond! Don’t wait for me to do it though, let’s see what you can do!

Questions, Feedback & Beta Testing

Need help with the build, found an issue, or have an improvement?

You can find me as LaserBacon on the:

BootyCallJones Discord server
West3D Discord server

Feel free to reach out, especially if you’re testing Endrborinn or trying an alternative A4T configuration.

Support Völund Forge

Endrborinn and my other Völund Forge projects take a considerable amount of time to design, prototype, print, test, break, redesign, and document.

The files are being shared so other builders can use them, experiment with them, and hopefully contribute improvements back to the community.

If Endrborinn saved you some time, improved your X-Max 3, or you simply want to help fund more filament, hardware, prototypes, and questionable CAD decisions, consider supporting Völund Forge on Ko-fi:

https://ko-fi.com/laserbacon

Support is never required, but it is greatly appreciated and helps me continue developing and releasing projects like this.

I am not affiliated with any product or company for any product recommendations made. They are recommended purely from my experience and use of those products, you are free to substitute them for similar products of your choice.

— Völund Forge / LaserBacon


Tagi