CREALITY K1 | K1C | K1SE - LID RISER V3 [FRAME EXTENSION KIT]
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Want to stay updated on new projects and updates? Join https:// patreon.com/LEOTE_approach for free!
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 102
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
LID RISER V3 [FRAME EXTENSION KIT] | Vents | Filament Sensor |
LED Strip | Hinges | Embedded LID
*If you have any issues with printing or assembly, feel free to message me, and
I'll do my best to assist you 😉.
*Because of the seam inside the walls, the internal space is reduced. To
clean it up, use scissors or a similar tool. Simply insert the scissors into the
wall and go back and forth a few times until it feels cleaner and there’s no
more resistance. This will ensure the vents will slide.
*If it's difficult to slide the pieces together, use a metal file to clean the
rails, especially on the wall pieces. This minor adjustment can make a big
LEOTE [approach]
CREALITY K1 | K1C |
K1SE - LID RISER
V3 [FRAME
EXTENSION KIT]
VIEW IN BROWSER
updated 3. 9. 2025 | published 3. 9. 2025
3D MODEL ONLY
difference. The fit is meant to be snug, so the pieces aren't loose. I had to
do this with some of my pieces. Some fit perfectly, while others were tight,
likely due to the printing process. Just file the rails a few times, and they
should fit perfectly.
/////FOR THE K1SE
The K1SE frame does not include the 4 threaded holes in the corners,
so the riser cannot be mounted in the usual way. Dennis Mckinney
created this solution, which I’m sharing here.
https://www.printables.com/model/1379103-creality-k1-se-lid-riserretainer-
clip
______________________________________________________________________________________________________________
/////LINKS FOR THE HARDWARE USED IN ALL MY PROJECTS * affiliate
links
INSERTS M3 x 4mm (L) x 5mm (D): https://amzn.to/3EovAVw
HEX SOCKET CAP M3 6mm-30mm (STAINLESS): https://amzn.to/
4imGAQW
HEX SOCKET CAP M3 6-20mm (BLACK): https://amzn.to/3R7wjx4
FLAT HEAD SOCKET CAP M3 4mm-12mm (STAINLESS): https://
amzn.to/3G3Z1wr
FLAT HEAD SOCKET CAP M3 8mm-25mm (BLACK): https://amzn.to/
43JeThP
FLAT HEAD SOCKET CAP M3 6mm-16mm (BLACK): https://amzn.to/
4kRgQNP
LED STRIP - COB LED Strip Lights Daylight 24V: https://amzn.to/
44M0iTd
LED CONNECTOR - JST-XH 2.54mm 1S 2 Pin Balance Plug: https://
amzn.to/3YrGG2C
________________________________________________________________________________________________________________
UPDATE 0.9 15/07/2025 - GUIDE UPDATED WITH THE BOM LIST FOR
CFS MOUNT V1 AND V2 VERSIONS
•
UPDATE 0.8 26/06/2025 - NEW TEST PARTS FOLDER
These parts were created to test the most critical fit between components
before printing the full model.
Start by printing just two test pieces and check if they snap together
correctly.
Confirm key dimensions and adjust your slicer scaling if material
shrinkage is affecting the fit.
Once everything looks good, print the remaining test pieces to be
sure your printer is dialled in.
If the vents do not slide properly into the wall, even when the size is
correct, there might be small bits of plastic left inside the channel from
overhangs or bridges.
To fix it, use a metal tool like a closed pair of scissors and run it through
the slot from end to end.
Keep doing this until the path is clean and the tool moves freely. That
should restore smooth movement.
UPDATE 0.7 09/06/2025 - NEW VENTS VERSION – CFS COMPATIBLE
FOLDER - VENTS_VERSION - CFS COMPATIBLE
FILE - [c]_x4_K1C_V3_VENTS_CFS_VERSION.STL
This updated part was designed for users who have the CFS system
installed on their K1, K1C, or K1SE.
When the CFS is mounted, the printer loses about 5 mm of travel on the Y
axis. That means even if the original vents part fits on the build plate in
the slicer, it will fail during printing because of that shift.
To fix this, I created a shorter version that stays within the usable print
area.
The original design had a wider side flange, which helped seal the riser
more effectively. Since that width is no longer possible with the CFS in
place, this new version keeps just enough material to maintain a proper
seal for materials like ASA or ABS.
[c]_x4_K1C_V3_VENTS_CFS_VERSION
UPDATE 0.7 16/05/2025 - NEW BACK WALL with FILAMENT SENSOR
INVERTED
This version allows you to install the filament sensor upside down.
The sensor is not directional, so it works the same way when inverted.
With this configuration, the cable connector is positioned at the bottom,
which means you can use a much shorter cable.
•
•
•
/////PARTS LIST FOR PRINTING THE RISER WITH THE CFS MOUNT V1
EXCLUDED PARTS:
LID
BACK FRAME - [a]_x1_K1C_V3_FRAME_BACK.stl
FRONT FRAME - [a]_x1_K1C_V3_FRAME_FRONT.stl
BACK WALL- [b]_x1_K1C_V3_WALL_BACK.stl
FRONT WALL - [b]_x1_K1C_V3_WALL_FRONT.stl
1x LEFT WALL CORNER - [b]_x4_K1C_V3_WALL_CORNER_L.stl
RIGHT WALL CORNER -
[b]_x1_K1C_V3_WALL_CORNER_R_PTFETUBE_HOLE.stl
HINGES - [c]_x1_K1C_V3_LEFT_HINGE.stl -
[c]_x1_K1C_V3_RIGHT_HINGE.stl
HANDLE - [c]_x1_K1C_V3_HANDLE.stl
LID CLOSER - [b]_x1_K1C_V3_LID_CLOSER.stl
FILAMENT SENSOR SPACER -
[b]_x4_K1C_V3_FILAMENT_SENSOR_3mm_SPACER.stl
NEW PARTS TO PRINT:
2x SIDE FRAME – [a]_x2_K1C_V3_FRAME_SIDE.stl
•
•
•
•
•
•
•
•
•
•
•
•
1x SIDE WALL - b]_x2_K1C_V3_WALL_SIDE
1x RIGHT WALL CORNER - [b]_x3_K1C_V3_WALL_CORNER_R.stl
1x UPDATED BACK WALL – CFS_MOUNT_KIT FOLDER
1x UPDATE LEFT WALL CORNER – CFS_MOUNT_KIT FOLDER
/////PARTS LIST FOR PRINTING THE RISER WITH THE CFS MOUNT V2
EXCLUDED PARTS:
BACK WALL- [b]_x1_K1C_V3_WALL_BACK.stl
1x LEFT WALL CORNER - [b]_x4_K1C_V3_WALL_CORNER_L.stl
RIGHT WALL CORNER -
[b]_x1_K1C_V3_WALL_CORNER_R_PTFETUBE_HOLE.stl
FILAMENT SENSOR SPACER -
[b]_x4_K1C_V3_FILAMENT_SENSOR_3mm_SPACER.stl
NEW PARTS TO PRINT:
1x UPDATED BACK WALL – CFS_MOUNT_KIT FOLDER
1x UPDATE LEFT WALL CORNER – CFS_MOUNT_KIT FOLDER
1x RIGHT WALL CORNER - [b]_x3_K1C_V3_WALL_CORNER_R.stl
_______________________________________________________________________________________________________________
*INSTALLANTION INFO - FILAMENT SENSOR CABLE
If you’re having trouble connecting the filament sensor because the cable
is too short, start by removing the printer’s bottom cover and cutting the
zip ties holding the cable in place. If it’s still too short, it’s likely glued
inside the raceway. In that case, you’ll need to remove the entire cable
cover and carefully free it from the superglue.
UPDATE 0.6 30/01/2025 - New Chain Wall
In this new version, the vents on the inside of the wall have been partially
closed to eliminate the noise that occurs when the chain rubs against
them during operation.
•
•
•
•
•
•
•
•
•
•
•
UPDATE 0.5 19/12/2024 - New closed wall versionUPDATE
0.4 | 22/11/2024 - Filament sensor wires
To get more slack for the sensor wires, you just need to remove the bottom
cover and cut the two (usually) zip ties holding the wires in place, and
you’ll have enough slack.
UPDATE 0.3 | 03/09/2024 - Material quantity by color
[a] - Polymaker PolyLite ABS Galaxy Dark Grey - 128.39g
[b] - Polymaker PolyLite ABS Black - 383.06g
[c] - Polymaker PolyLite ABS Green - 83.1g
UPDATE 0.2 | 14/08/24
Check this video for fine-tuning filament settings and dimensional
accuracy:
If the sensor cable is too short and you can't connect it to the sensor,
you'll need to remove the bottom cover of the printer, and you’ll see
some zip ties holding the cable in place.
•
UPDATE 0.1 | 26|07|2024 - The project is complete
Below is the list of updated files, including a new file.
LIST OF UPDATED FILES:
[b]_x1_K1C_V3_WALL_CORNER_R_PTFETUBE_HOLE
[c]_x1_K1C_V3_HANDLE
[c]_x1_K1C_V3_LEFT_HINGE
[c]_x1_K1C_V3_RIGHT_HINGE
[c]_x4_K1C_V3_VENTS
NEW FILES:
[b]_x4_K1C_V3_FILAMENT_SENSOR_3mm_SPACER
*Apply these spacers with the filament sensor to distance it from the LEDs
_____________________________________________________________________________________
NEW INSERTS
The inserts have been updated. The 5mm inserts left marks on the frame's
exterior, so please use the new 4mm inserts instead.
Link to new inserts: https://amzn.to/42NE3e2
SLIDING
For smooth sliding like in the video, use scissors or a metal object that fits
inside the walls. Move it back and forth several times. This will clean up
the internal overhangs that cause the slider to not move smoothly.
RISER FEATURES:
MOUNTING SYSTEM: The parts are secured together with bolts and
inserts. The only glued part is the flap that closes the cut-out on the
back of the LID.
•
VENTILATION: It has 360° ventilation, the highest ventilation I have
ever designed in a riser.
EMBED LID: The LID is embedded in the frame, giving a cleaner
look. Despite being embedded in the frame, the usable space inside
the printer is the same as the V2 50mm [another of my projects].
HINGES: The hinges open 110° (allowing printing with the LID open)
and have an inner flap that ensures alignment of the LID with the
frame.
HANDLE: It has a handle (press-fit, but I have a version with a fixing
tab for the LID if needed in the future).
LIGHTING UPGRADE: There is a predefined space for an LED strip.
One of the inner corners has a fixation point for the wires if LEDs are
installed.
FILAMENT SENSOR REPOSITIONING: Fixation points on the back
wall to place the filament sensor inside the riser. One of the side wall
parts has a hole for the PTFE tube.
CHAIN ADJUSTMENT: Mounting points on the back wall for the piece
that allows adjusting the chain height.
/////THINGS to ADD
Front Chain Riser (12mm) - LINK
////ATTENTION
Make sure the bolts aren't too long. They shouldn't go past the
frame's thickness to avoid damaging any internal components. [ The
bolts listed have been tested ]
/////IMPORTANT
Before starting the print of the riser, I recommend printing this tool
https://www.printables.com/model/899470-xyz-accuracy-testcalibration-
tool to test the dimensional accuracy of your printers.
Use this tool https://www.printables.com/model/480907-shrinkagecalculator-
dimensional-calibration-tool to determine the correct scale
based on the filament shrinkage you’ll be using.
The riser pieces were developed with very tight tolerances (0.2mm)
to ensure proper alignment and functionality of the assembly, so it’s
important to make sure everything is well-calibrated or that you
understand what is needed for everything to work correctly.
///// ASSEMBLY GUIDE
Scroll to the bottom of the download page to find the installation
guide.
•
•
•
•
•
•
•
•
•
•
•
•
•
Model files
/////All files are labeled with material/color and quantity
[a] - ABS or similar material | Color 1
[b] - ABS or similar material | Color 2
[c] - ABS or similar material | Color 3
[ The vents [c] can be printed in a different material - PLA ]
[ Do not print the hinges and the chain adjustment piece in PLA - use a
more heat-resistant material ]
x(number) - number of parts to print
