1 / 9
Trolling Motor Steering Servo Mount — zdjęcie 1
1 / 9

Trolling Motor Steering Servo Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

I designed this servo mount to add remote-controlled steering to the Water Snake Venom trolling motor.

Ocena
0 / 5
Polubienia
3
Pobrania
45
Wydruki
0
Wyświetlenia
190
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Trolling Motor Steering Servo Mount – Water Snake Venom

I designed this servo mount to add remote-controlled steering to the Water Snake Venom trolling motor. It uses a 60kg waterproof RC servo paired with a HotRC DS650 remote.

Designed specifically for the Water Snake Venom, this mount replaces the stock steering setup with a simple 3D-printed servo-driven system.

This design took alot of test prints to get everything working and fitting just right and I have been using it on the water without issue in the Florida heat for an entire season.

If you print and make one please post some pictures of your setup.

Video of it in action and using my DIY GPS anchor setup

Video close up of the servo mount

☕ Enjoying the design?

If you found this design useful and it worked well for you, consider buying me a cup of coffee! Your support helps keep me designing, testing, and sharing more projects.

https://www.paypal.com/donate/?hosted_button_id=SSXWCSQABBTUC

Thank you for supporting my work!

🖨 Print Settings

All parts except the bushing:

  • Material: ASA

  • Walls: 10

  • Infill: 40% Gyroid

Bushing:

  • Material: PETG

  • Infill: 100% solid

The PETG bushing provides a smooth sliding surface against the ASA parts.

🔩 Required Hardware

  • 6 × #8-32 × 3/4" screws

  • 6 × #8-32 threaded heat-set inserts

  • 1 × 60kg waterproof RC servo

  • 1 × metal servo horn

  • 8 × M2.5 × 16mm socket-head screws for mounting the spur gear

Hardware Links

#8-32 Heat-Set Inserts:
https://www.amazon.com/dp/B08P1SKYCB

#8-32 × 3/4" Screws:
https://www.amazon.com/dp/B0BNN85TMP

60kg Waterproof Servo:
https://www.amazon.com/dp/B08HYX5SX3

Metal Servo Horn:
https://www.amazon.com/dp/B0DJVF8CKT

M2.5 × 16mm Socket-Head Screws:
https://www.amazon.com/dp/B0DCKC41W3

⚠ Important: The screws that come with the servo horn will NOT work for mounting the spur gear. You need the M2.5 × 16mm screws listed above.

🛠 Installation

The trolling motor head must be removed to install the mount.

  1. Install the 8-32 heat set threaded inserts.

  2. Install the servo horn and spur gear onto the servo using the M2.5 x 16mm screws.

  3. Feed the servo wire through the dedicated hole and install the servo.

  4. Secure the servo wire using a small ziptie to the dedicated zip tie loop which you can see in this video https://www.youtube.com/shorts/6zZQtefQGEI

  5. Remove the trolling motor head.

  6. Remove the stock depth stop.

  7. Save the stock depth-stop screw knob and nut — they are reused with the printed mount.

  8. Slide the printed components onto the trolling motor shaft and secure using the 8-32 x 3/4'' screws.

  9. Reinstall the depth-stop knob and nut into the newly 3d printed one.

  10. Reinstall the trolling motor head.

  11. Connect your RC system and set the servo steering limits.

Photos showing the threaded inserts and screws

Additional Items I used:

Hot  RC DS650 Remote Control 

https://www.amazon.com/dp/B0FNDDMZGX?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_14&th=1

RC servo angle expander 

https://www.amazon.com/dp/B0FP72QZ3Q?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_17

Servo Extension Wire

https://www.amazon.com/dp/B0D92YQK2Q?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_16&th=1

Enjoy your new remote-controlled Water Snake Venom! 🚤

Tagi