Liczymy pasujące modele…
So I needed a storage solution for my kayak pedal drive. It is a knock off chineese hobie mirage flap pedal drive. I have Gladiator geartrack slat wall. I designed a storage rack for it. I still havent found a print orientation I like. I…
I really didn't like how the 2 small front compartments would hold water in the depressions. To dry these you have to remove the screw and hold the nut internally and reinstall after. I designed and 3d printed a resolution. These are a…
Yes, this project is destined to end very badly. I've printed 2 handles to steer a 2 meter training kite that wraps perfectly around a kayak paddle. What could possibly go wrong?!
🛶 Stampato in PETG, resistente e adatto agli ambienti umidi, questo pratico porta attrezzi è progettato su misura per il kayak Triken 330 . 🔧 È suddiviso in due sezioni per offrire maggiore comodità e organizzazione. 💧 Fori di drenaggio…
Find 3D-Printed RC cars here.
Find 3D-Printed RC cars here.
I bought some cheap kayak wheels from aliexpress. They came with one strap that you somehow had to use to secure the wheels under your kayak. I dedicated two 1" straps to the wheels. Now I can just hook the straps to the wheel frame. The…
Some older Perception kayaks (WW (e.g. some pirouette super sport) and Canoe Polo boats) came with foam seats that could be swapped out for a different size fit. The seats attached via a lug on each side that locks into a corresponding…
Battery box snaps on the post in the front hatch. I added loops on the sides to attach a strap if needed but it doesn't need it. My battery size is 5.94" X 2.56" X 3.7". It's a 12V 7Amh battery that powers my fish finder.
A mounting system for the 3D Sets kayak to the Mogster roof and back racks. Made to look like a looped rope, this mounting system is meant to blend in while still holding the kayaks secure. "F" and "R" are for the front and rear of the…
the latch for my kayak broke. Redesigned it and replaced it with this print plus 35mm M6 stainless bolt and a m6 nyloc nut. Dont know all the models this will fit. Mine is similar to a reelyak. Printed mine in asa with support but petg…
Following a user suggestion, here's a simple, fun kayak toy boat for desk display, bath time play, dioramas, etc. This model comes in two variants: A realistic round-bottom version which captures the classic kayak hull shape for a more…
This model is compatible with the lego system.
My Sun Dolphin kayaks had foam rubber drain plugs that were in bad shape, so I created replacements in Tinkercad. The kayak drain hole is 11mm, and this drain plug is 11.5mm in diameter. Printed in TPU and hollow (three outer walls) so…
Slide used to attach wheels to a backpack and self-made - stroller.
I created these accessories to make using my Watersnake ASP 18lb trolling motor a bit easier on the water, and address some issues I found installing on my Pelican kayak. The motor and mount are a great value, and instead of using PVC…
I bought a Big Water 132 and needed to raise my kayak cart to prevent the beach wheels from rubbing the body of the cart. This will lift the frame an additional 2 inches to provide the extra clearance. You will need longer bolts and wing…
This is a remix of the Inflatable SUP/Kayak Halkey-Roberts Valve inflation adapter posted by lieutenantglorp here: https://www.thingiverse.com/thing:2354966 . It was too small for my hose which is why I remixed it. It should fit most…
I designed these to fit my Perception Outlaw 11.5, I'm sure they fit others as well. I printed these in TPU with 20% infill Diameter of top - 31.75mm Diameter of bottom - 26.8mm Height - 25mm
This is a holder to attach a GPS bicycles computer on a racing/fitness kayak. Apparently it's common to use a GPS watch such as one from Garmin for racing/fitness kayaks to know the speed/distance, as I have seem several watch holders in…
100mm×52mm×9mm Solid almost indestructible part. Print with 15-20% infill. 0.2 or0.3 layer height. M8 holes fits the imperial size shown on kayak mount plate ¼-20 x 7/8 stainless steel bolts recommended. Reworked the part with more…
Designed using Blender. Has .2mm tolerances in between the pieces. Printed in PETG with no supports on an Ender 3 S1. Holes for 2mm rods to keep crate together. I used paperclips with mine but had these in mind at 150mm and 300mm with the…
Printed in PLA with no supports on Ender 3 S1 Designed to mount with any two existing bolts for the front enclosure on the Ascend 128x. Have to extend the Stern plug to reach the enclosure.
Printed in PLA on Ender 3 S1 with no supports. Designed to use two originals mounting holes and bolts around the front enclosure to mount the Power Converter .
A simple thumb nut 1/4-20 to fit the seat stud of my Jackson Kayak. If I get ambitious I might create a model to use threaded inserts later. Let the stud clean up the plastic threads, it will be a little snug. Category: Sport & Outdoors
A simple replacement (mostly temporary) thumb screw/nut Loosely based on the Pyranha Foot Rest thumb nut (M6x1.0) May fit other models, let the bolt threads clean up the plastic threads. If I get ambitious enough later, I might create a…
The original model has been working great all summer if you want to replace the original clip. I've been frustrated with the 2 part clip on these kayaks so I modeled another clip that ties directly to the strap. The strap needs to start…
I have a Lifetime Tamarack 100. I was adjusting my seat on the river and this clip popped off, never to be seen again. I found the model by Hparsonst and gave it a try. It was a little thinner than my original and didn't clip on securely.…
If you find yourself bracing with the edge of the blade, or rolling with too much or too little angle on the sweep, or perhaps just haven't got a local stockist, then this model should help out. It's a bit of a work in progress, but fully…
So I needed a storage solution for my kayak pedal drive. It is a knock off chineese hobie mirage flap pedal drive. I have Gladiator geartrack slat wall. I designed a storage rack for it. I still havent found a print orientation I like. I…
I really didn't like how the 2 small front compartments would hold water in the depressions. To dry these you have to remove the screw and hold the nut internally and reinstall after. I designed and 3d printed a resolution. These are a…
Needed to hang the kayak paddles when not in use. Bracket is made for the handles to snap fit and my be a bit tight for some paddles. Designed in Fusion 360, printed with PETG in Prusa MK3 with .02 nozzle.
Brackets to replace the strap brackets on the Pelican Kayak Cart
Got a new printer so this will probably be improved upon this next pool season.
Snap on shim for aligning the Old Town seat to keep the seat out of the way of the dry storage lid. There are different sizes in case the tolerances require different. I used the .35" shim for my AP120 seat. Files are saved with thickness…
Made this to rivet on to the side of my sit-on kayak. Used 3/16 x 1" marine pop rivets. Should work find with self-tap screws and screw/nut fastening. The print is in PETG to be UV resistant. The hold is pretty strong but it definitely…
Made this to rivet on to the side of my sit-on kayak. Used 3/16 x 1" marine pop rivets. Should work fine with self-tap screws and screw/nut fastening. The print is in PETG to be UV resistant. I don't think you have to use every rivet hole…
For instructions on how to design and print your own, go to: Designing Multiplanar Origami Printing Multiplanar Origami Open the 3mf file as a project in Prusaslicer to see when to add the mesh and where the Kapton (to prevent adhesion)…
This is a replacement boat plug that has an opening of about ¾" or about 19mm. It has a groove for grommet ¾" OD and 9/16" ID and 3/32" cross section. Since you print it handle down you will get a nice flat seat and may not need the…
Tracks a hella straight line (seriously effortless) but way more difficult to maneuver than the original. Designed for surfing easier longboard type waves and distance paddling. Attaches with the factory hardware & fits flush to the…
Tappo per Kayak con Fori da 8mm Questo tappo è progettato per limitare i fori di drenaggio sul fondo del kayak, impedendo che piccoli oggetti come piombi, galleggianti e artificiali possano cadere e andare persi in mare. Il design include…
The part behind of the foot block, broke so is a new one to repair your foot block without change the entire piece.
This tray is designed around a rod holder mount that came stock with my kayak. For the mount design I used an already existing one I found on OnShape and made the tray based on that. It uses 2 m4 bolts and hex nuts, ideally I would have…
Kayak gear track modeled after a scotty track. 45mm wide and 180mm long. 5mm screw holes with countersink. Print upside down with tree supports for the countersinks. i haven't tried without supports but I like to be safe and not have…
A tool, in two parts, for unscrewing a broken Padeye from a Hobie kayak. It also works to remove and replace an un-broken padeye, of course. This is my first design and will probably be useful to no-one but myself.
Kayak bucket to bring lures on board without the need of tackle boxes. I have a small kayak without much space to have my different tackle boxes laying around so I use this to have everything organised and ready to go. The lip diameter is…
This is a relatively basic rudder model I created to fit the Haswing Protruar Brushless 12v Trolling Motor. This motor is sold under other names as well, so if you have a chinese 12v brushless trolling motor chances are this will fit. The…
I needed a cost affective towable kayak bait tank. I had used a bucket and a battery operated air pump but since fish release ammonia, they still didn't last long. Keeping the bait in the water is likely the best approach for a kayak.…
Yes, this project is destined to end very badly. I've printed 2 handles to steer a 2 meter training kite that wraps perfectly around a kayak paddle. What could possibly go wrong?!
This is like super basic. Uses an m3 bolt and nut on the clip, keyhole on the cupholder allows it to slip on/off and rotate a bit with fore/aft movement.
If a padeye on your kayak breaks or is lost then this is can be a useful replacement. In addition to the printed part you will need an eye bolt to screw into the center hole; I used ¼" with 20 threads per inch in this design since that is…
This couples a 150 kg/cm servo with an electric trolling motor shaft(30mm). Print with solid walls in PETG or stronger.
Spare part/replacement for water drain plug: Kayak: Prijon T-Canyon (ca. 1995) Possibly also fitting for other Prijon Kayaks. Main Slicing parameters: - Slicing parameters used for Prusamet PETG - 0.2mm layer height - perimeters: 4 -…
Watch holder to be applied via suction cups to the Kayak. Since each boat has its own shape, I inserted various 3D models with different angles to adapt to the attachment surface. The two suction cups are 40mm in diameter and have a M4…
Sand and dirt can get into the mount for the Oru Kayak skeg ; use this protector to keep it clean when you transport or assemble your kayak. When you are ready to insert the skeg, just turn the kayak upside down, remove the protector and…
Rail covers to protect my bare foot from resting against the rail when paddling my crescent crew. I assume it will fit on other crescent kayaks as well.
Made in two parts. Camera mount is PETG. Base support is TPE 83shore. Depending on the profile of your Kayak switch the rubber support. There is a flat variant or a ‘vee’ variant (recently made for a friend). Uses / connect to standard…
The standard valve for many air tents/inflatable kayaks and pack rafts etc is the “Boston” valve. One hole for inflation and deflation, but two different caps; with the small cap removed the inflatable can be blown up, as it includes a…
decathlon itwit kayak seat air pump end which fit to decathlon mattress pump
Replacement Vibe kayak skid plate. Should work for- Shearwater 125 Cubera 120 Hybrid Vibe Sea Ghost 110 and 130 Printed in PETG 100% infill. ABS, ASA or Nylon may be better. Original linked below if they ever get it back in stock.…
This is a holder to attach a Garmin type GPS / bicycles computer on a racing/fitness kayak. Apparently it's common to use a GPS watch such as one from Garmin for racing/fitness kayaks to know the speed/distance, as I have seem several…
Our kiddie-sized Lifetime Wave kayaks have a drain hole drilled in the bow on the upper deck, and we've lost the plugs. The kayak hull filled with water after just a couple hours goofing around on the lake. I'm assuming the open hole on…
Well, better than my previous rudder ( http://www.thingiverse.com/thing:806945 ). Rotating the worm gear both adjusts the rudder angle and also tilts the rudder fore and aft. For normal steering angles (+/-20 degrees) the tilting does not…
This is a custom-designed T-grip for quickly converting a kayak paddle into a single-blade canoe-like paddle. Comes in handy when paddling through narrow/constrained waterways where two-blade paddles can get easily tangled up in water…
These are intended for temporarily placing your kayak paddle while fishing. They will not clamp the paddle down they just give you a place to set it down. These should be printed in pairs. You may find some of my other kayak fishing…
This is a two part model intended for mounting a Garmin Striker 4 transducer via scupper hole on a kayak. The top and bottom pieces can be attached together using zip ties that go through the provided holes. This makes it a bit more…
This is a small cup that mounts onto the rail on a kayak. Shown on a Magellan Pro Angler 10.3. The primary usage would be holding small items while fishing, changing lures, etc. This may fit some drink contains as well. The design has a…
🛶 Stampato in PETG, resistente e adatto agli ambienti umidi, questo pratico porta attrezzi è progettato su misura per il kayak Triken 330 . 🔧 È suddiviso in due sezioni per offrire maggiore comodità e organizzazione. 💧 Fori di drenaggio…
SUP Kayak Drink Holder with Bottle Opener – This versatile holder fits a wide range of beverage types, from cans to bottles, and keeps them secure while you paddle. It attaches quickly to straps or ropes, making it perfect for stand-up…
Find 3D-Printed RC cars here.
Find 3D-Printed RC cars here.
My kayak warranty forbid to screw accessories in so I created this adapter plate to provide a flat surface that can be glued on the kayak shell. 2 models are available, a short and a long one.
Printed bungee mount, works with ¼ max diameter bungee and hardware/similar linked below. ¼ - 20 thread kayak rail/track mounts. https://tinyurl.com/4yf2yab8
A fishing rod holder that fits into the "slide-in Aero rac receiver" mountings included with inflatable paddleboards and kayaks sold by BOTE. I printed mine in PETG using a .4mm nozzle using a layer height of .2mm. I used 30% gyroid…
Shoutout to ScootyPuffJR for the base design for their kayak. Our Perception Sound 10.5 Kayak's have slightly larger holes and style so I remixed it to work better for the Sound 10.5's. Printed in TPU @ 20% Infill. Print it top/cap size…
Kayak mount for a Garmin Etrex Legend GPS receiver. Mine has a serial port, no USB. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: Doesn't Matter Supports: no Resolution: 0.2mm Infill: 15% Filament: Generic ABS black Notes:…
Deck fitting for bungees or deck lines. Use a 4 or 5mm oval head bolt. This one has only one hole for the line. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: Yes Resolution: .2mm Infill: 10 perimeters to ensure…
Wall mounted rack to hold four blades. Print with the big end on the bed. With my Prusha MK3S I don't need supports. If I print with a 0.6mm nozzle and a 0.4mm layer height it takes a little under 7 hours to print. I used PETg, but really…
Beer holder for a kayak. Can be attached using the kayaks rubber strings. It also has a hole at the bottom, so you can also fix it in place with a screw. Fits a 330ml, 500ml and a pint. Does get a bit tipsy when a pint is inserted if you…
This is a Scupper hole plug to keep water from coming into the sit-on-top kayak from the scupper holes. These are printed in flexible filament to allow for a tight flexible fit. to assemble put the ball into the plug and glue on the grill…
For assembly you need Metal pipe 12-12.5 mm thick Bolt M5 15 mm (2 pcs.) Bolt M5 35 mm, can be longer (2 pc.) Bolt M4 20mm (4 pc.) Nut M4 (4 pcs.) Nut M5 (3 pcs.)
Hi! This is Sup board drink can holder i created for my friend which you might enjoy as well! Model is inspired by some video i saw online, but i couldn't find one for my requirements so i made one myself. No supports required
This Can and Phone Holder is designed to fit a can with a koozie <85mm. The phone holder slot is also 85mm in length and 15mm in width. It fits my Samsung Galaxy A32 with the case perfectly. My print of this variant of the design was done…
Decathlon x500 drop stitch kayak foot peg replacement Filament PETG 0.4 mm nozzle PRUSA 4S
This is a cup holder that will mount on a t track found on kayaks and canoes. Use a ¼-20 t bolt and nylon lock nut. You will also need 3 m4-8mm button head screws and 2 m4 brass heat inserts. Recommend printing is PETG or ASA. Print with…
Unlike my recent windsurf mast holder, I just went with a single screw hole. This should be enough for lightweight paddles (as long as the screw hold is solid). With the trim plug and right choice of screw (or paint), you can make very…
Designed some simple kayak paddle drip stops, designed to print in a flexible filament like TPU. The bore is 1.13 inches, which fit my 1.14 inch paddle shaft with a perfect balance of grip and adjustability. Print with low infill for best…
Kayak Vibe Sea Ghost 130/110 Hook for the trunk bungee to better secure everything. Used PETG Infill 20% Triangle 4 Walls and 4 top/bottom layers
I needed a way to secure my kayak on my car roof. You only need to put the stopper with the webbing attached into the trunk or in between a door and you have a secure attachment point.
Wall hook for Yakima JLow. Probably fits many other Kayak Racks such as the Thule or any other that are similar in styles. Quick and easy print. Versions: V1 First upload (23-Sept-2025) Print Instructions: Print on its side In the slicer,…
