1 / 3
DJI Mini 4k Wall Mount — zdjęcie 1
1 / 3

DJI Mini 4k Wall Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

DJI Mini 4K wall mount, arms out. Nose down, gimbal untouched, no supports. 217mm wide — check your bed.

Ocena
0 / 5
Polubienia
2
Pobrania
5
Wydruki
0
Wyświetlenia
33
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

I wanted to mount my DJI Mini 4K on the wall but couldn't find anything I liked, so I made one. Built with the help of Claude and this GrabCAD model of the Mini 4K: https://grabcad.com/library/dji-mini-4k-1 — that model was only used to take measurements from, nothing of it is included here.

First time publishing anything. Hope it helps someone out.

PS — yes, AI was involved, i know, i know. For what it's worth it wasn't a "type a prompt, get an STL" job/ the dimensions came off that GrabCAD model, the bracket got collision-checked against it before I printed anything, and the backplate shape is a topology optimisation rather than something drawn by hand. Then I printed it and put it on my wall. Write-up below is tidied up by Claude because I'd rather be printing than typing.

How it holds

The drone sits nose down, arms unfolded, belly against the wall.

The weight rests on the two long front landing legs — the pair either side of the camera. They drop onto a shelf at each end of the bracket, with a cheek on both sides so they can't slide. Those legs are built to take landing loads, so they're the right thing to hang it from, and they're 43 mm long so the shelf position is forgiving.

The cradle in the middle carries no weight. It just keeps the fuselage straight, and the two tabs sit about 3 mm over the canopy so the drone can't lean out from the wall. Four small pads set how far it stands off.

Nothing sticks to the drone — no tape, straps or magnets. The gimbal hangs free at the bottom with about 15 mm of air around it, so nothing can press on it.

Fitting it — it does NOT drop in from the top

This catches people out. With the arms unfolded, the rear arms are much wider than the cradle, so it can't be lowered in from above.

  1. Unfold the arms

  2. Hold the drone square to the wall and level

  3. Push it straight back — the fuselage goes between the cradle walls, the canopy passes under the tabs

  4. Let it down the last millimetre; both front legs land on the shelves

To remove: lift a couple of mm and pull straight out.

Hardware

3 × #8 pan head screws (7–8.5 mm head, shank under 5 mm) with drywall anchors. Two keyholes 84 mm apart and level, one anti-lift screw at top centre.

Leave the two keyhole screws about 4 mm proud, hook the mount over them and let it drop — it slides 12 mm and locks. Then drive the third. The keyholes are counterbored so the heads finish flush and end up hidden behind the drone.

Printing

The part is 217 mm wide. That fits a 220 × 220 usable area with roughly 1.5 mm each side — it printed fine on my Ender 3 S1 Pro, but it's tight. Level the bed and watch the far corners on the first layer. If your bed has clips or a big origin offset you may not have the room. It will not fit an A1 mini or anything in the 180–200 range.

  • No supports — every overhang is 45° or steeper

  • Print flat on its back, as oriented in the file. Don't rotate it: you'll need supports, and the layer lines end up running the wrong way through the leg shelves

  • 4 perimeters, 20% infill

  • Mine is PETG-CF at 0.28 mm. Plain PETG or PLA is plenty for a 249 g drone

  • Around 50–60 g, 5–7 hours

Tagi