Lian Li O11 Vision 2-Inch Riser Feet – Bolt-On, Set of 4
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Lifts the case 2 in (50.8 mm) for more bottom-fan airflow. Each riser wraps a stock foot and bolts into its thread.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 11
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Raises the Lian Li O11 Vision exactly 2.0 in (50.8 mm), for more room under the bottom fans. The front I/O ports end up easier to reach too.
Built from Lian Li’s CAD model
The O11 Vision stands on four moulded feet with near-straight outer faces and ~45° sloped inner faces. The front-right one is longer because it houses the front I/O. Each riser follows its foot and was checked against every part of the official model.
How it attaches
A 10 mm socket wraps the stock foot with 0.6 mm clearance; the rubber pad drops into its own pocket.
A stem goes up into the screw well in the middle of each foot, so nothing wobbles or twists.
Bolted (most secure): swap each foot’s stock screw for a #6-32 × 1-1/4" that goes up through the riser and the foot into the case’s own thread. The risers stay on when you lift the case.
No tools: or leave the stock screws in. The stems stop below them.
The front-right riser wraps the I/O foot and stops 7.5 mm below the ports, so plugs fit as before.
Print order
1_PRINT-FIRST_Fit-Test_all-4-corners: about 145 g. Press each piece onto its foot first.
2_PREFERRED_All-4-Risers_one-plate: the full set, 178 × 203 mm, fits a 220 mm bed.
Single risers: the same parts one at a time, for small beds or reprints.
What you’ll need (bolted option, not included)
4 × #6-32 × 1-1/4" pan-head machine screws (or M3.5 × 30–32 mm). Length matters: 1" won’t reach the thread, and 1-1/2" pokes 8 mm into the case.
A #2 Phillips with a slim shaft at least 60 mm long.
Print settings
Setting | Value |
|---|---|
Material | PETG (ASA or ABS also good; PLA+ in a cool room) |
Orientation | As exported, base down |
Supports | None |
Nozzle / layer | 0.4 mm / 0.2 mm |
Walls | 4, with 5 top and 5 bottom layers |
Infill | 25 % gyroid |
Plastic | About 550 g per set, fit test about 145 g |
Install
Shut down, switch the PSU off and unplug the power cord.
With a helper steadying it, tip the case back so the front feet lift about 10 cm.
Bolted: remove the stock screw from each front foot.
Press the front risers on (the long one goes under the USB ports) and screw them in from underneath. Don’t overtighten; it threads into thin steel.
Repeat at the rear.
STEP files and the Python source are included, so you can build other lifts, for example 2.5 in.
Images are renders on Lian Li’s CAD model. Not affiliated with Lian Li.