1 / 6
CORE One: New Enclosing Chamber Fan Cover (Injection Molded Fan Grid) — zdjęcie 1
1 / 6

CORE One: New Enclosing Chamber Fan Cover (Injection Molded Fan Grid)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Enclosing chamber fan cover for the CORE One's new injection molded fan cover. Drop-in fit, stock fans and screws.

Ocena
0 / 5
Polubienia
4
Pobrania
3
Wydruki
0
Wyświetlenia
16
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Open Community License v1.1

Overview

The Prusa CORE One build / upgrade guides  show a new injection-molded fan cover used in place of the previous laser cut acrylic flat panel.

It encloses both chamber fans, replacing the original flat laser-cut acrylic fan grid. Prusa notes the assembly procedure is the same for both versions.
https://help.prusa3d.com/guide/3-back-assembly_1004166#1006647

The molded cover isn’t offered as a download or as a separate part, so I modeled a printable version meant for printing in Prusament PCCF as with all recent upgrade printed parts within the chamber.

This is a drop-in replacement. It uses the stock fans, the stock M3x30 screws and the existing nuts in the back panel. No modifications to the printer are needed.

Features

  • Fully enclosing shroud with continuous walls, matching the molded part.

  • Honeycomb grille matched to the molded cover: 28 open hexagons per fan, with the hub centers closed off like Prusa’s part. Cell size and web width were measured from the guide photos.

  • Stock screw stack: the screw seats are 2.0 mm thick, the same as the original acrylic grid, so the stock M3x30 screws engage the back-panel nuts exactly as designed.

  • Stock grille position: the outer face sits where the original grid did, so the cover reaches no further into the chamber than stock.

  • 1.0 mm blade-relief pocket over each rotor. It adds space between grille and blades for cleaner intake airflow, without moving the cover or changing the screw seats.

  • Thermistor holes in the stock positions for the chamber thermistor routing shown in the guide.

  • Open cable notch at the rim with a raised zip-tie saddle, as on the molded cover. The fan harness lays in after the cover is mounted.

  • Fit verified against Prusa’s official CORE One CAD assembly. That covers fan positions, mounting nuts, corner press nuts (3.4 mm clearance) and the coreXY plate (11 mm clearance).

Specifications

  • Size: 129 × 72 × 26.4 mm, including the cable saddle

  • Mounting holes: 4 × Ø3.4 mm clearance holes on the stock centers

  • Weight: about 32 g in PC-CF

  • Hardware: the 4 stock M3x30 screws from the original grid, plus 1 small zip tie (up to 4 mm wide)

Print settings

  • Orientation: as supplied, grille face down on the sheet. No supports needed; the cable saddle has a built-in 45° support wedge.

  • Material: designed for PC-CF. PC and ASA may also work.

  • Nozzle: Hardened 0.4 mm

  • Layer height: 0.2 mm

  • Perimeters: 4, so the 2 mm walls print solid

  • Infill: any; the part is almost entirely perimeters and solid layers

  • Adhesion: a brim is recommended for PCCF and PC

Installation

Follow the Chamber fans steps in the official CORE One upgrade or assembly guide. The procedure is the same as with the original grid.

  1. Fit the fans with the side without the sticker facing the cover, with the cables running from the corners toward the center.

  2. Route the thermistor through the center holes the same way as on the original grid. Keep the metal tip from touching the cover.

  3. Place the cover with the cable notch and saddle at the bottom (toward the coreXY).

  4. Insert the 4 stock M3x30 screws through the cover and fans into the back panel. Tighten them snugly, but don’t overtighten.

  5. Lay the fan and thermistor cables into the rim notch and secure them to the saddle with a zip tie.

This is an independent remake, not an official Prusa Research part as Prusa has yet to make a model file of the new fan cover officially available. It is based on the guide photos and Prusa’s published CORE One CAD, which was used to check the fit.

Tagi