3D print PCIE slot for 120mm Fan to replace fans on GPU
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
It's a PCIE Fan mount for 120x120x25mm fan that you screw in with standard fan screws.
- Ocena
- 5 / 5
- Polubienia
- 122
- Pobrania
- 1167
- Wydruki
- 1
- Wyświetlenia
- 6806
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
It's a Fan mount for 120x120x25mm fan that you screw in with standard fan screws. You can also print joints to add up a second 120mm FAN.
That mount replace a 2x 92x92x8mm to a 120x120x25mm. It helped me to get 7C lower temperatures under same RPM as old ones. Main focus was to bring fans close as i can to the finstack and cover most of it. Mount takes about 1 slot, but uses second pcie mount to prevent rotation. Second pcie mount is cut 1mm from the case, so you can still squeeze a PCI card. I didn't try to mount third fan, you can try but i don't guarantee that bracket don't flex or brake ;D
- Entire graphic card with this, takes around 2.6 slots.
- Material used to print that thing was a premium PET-G - Devil Design blue translucent
- Full printed thing weight 13g in PET-G with 100% infill, so it's not that much.
- If you print it in PET-G it will bend a little downward with 2 fans, with one is ok. For best results try PLA or ABS, they don't flex like PET-G
To mount this, you need first mount that fan bracket with fans. You need to align with holes and cutouts near MOBO. After that you can mount your GPU i don't guarantee that your model of GPU will be compatible. Mine GPU is a EVGA 3060 Ti XC GAMING, and plastic shroud from it is about 14mm in height with stock fans.
If you have a place in your case, you can still use it as additional air to your GPU fans. Your gains will be around 1-3C.
Printed on heavy modded ENDER 3 with Direct Drive
PRINTING PARAMETERS
- Quality
- layer height: 0.08-0.16 (for bonding - lower is better)
- nozzle: 0.4mm
- Walls 0.8mm is good enough
- Horizontal expansion: 0
- Wall ordering: From outside to inside
- Minimal line width: 0.2mm
- print thins walls: yes
- minimal feature size: yes
- TOP/BOT 0.8mm
- Pattern: concentric
- Skin overlap percentage: 20%
- Monotonic Top/Bottom order
- Ironing - YES
- Speed
- Infill 48 -Outer 15 -Inner 24 -TOP/BOT 24 -Travel 150
- Initial 15 and initial travel 100
- Infill
- pattern: cubic
- density: 100% if you want 100% to be sure
- infill line multiplier: 2
- connect infill lanes: YES
- Material
- PLA, ABS or PET-G (ABS is better and lighter than PET_G)
- Printing temp: 250C with PET-G. You can try 230C if your cooling can't keep up, but it will be weaker.
- build plate: 75-80C
- Flow 101%
- Outer wall flow: 100%
- You need supports!
- Travel: retraction: 1mm (direct drive)
- brim: 3mm
- distance 0.025mm
- Cooling yes 100% for dimension accuracy and overhangs
I'm sharing this project only for PERSONAL USE!
If you want to sell it, we need to talk about licensing this…
If you have found that project good, here is a page where you can buy me a coffee and vote on what i will do next: https://ko-fi.com/thesunshinedude
Or just drop a like on my artstation:
https://www.artstation.com/lukasz_kiebala
Support and request:
[email protected]
https://discord.gg/6NKQtxDTGQ
Best regards, Sunshine