1 / 4
SW2 BIQU H2 V2S REVO Carriage Mount and fan duct 5015 and Bl-Touch 3.1 — zdjęcie 1
1 / 4

SW2 BIQU H2 V2S REVO Carriage Mount and fan duct 5015 and Bl-Touch 3.1

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Carriage Mount for BIQU HE V2S REVO on Sidewinder X2

Ocena
4 / 5
Polubienia
18
Pobrania
168
Wydruki
2
Wyświetlenia
1687
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

You will find the whole project to be able to mount the BIQU H2 V2S REVO on an X2 artillery.
The assembly allows to put a BL_Touch (either a TOUCH_MI, or a BL touch)

The assembly is planned for a 5015 blower.

For the attachment on the cover, you will need a rubber band of the same thickness as the original one.

Printed in PETG in 0.16mm.

If BlTouch you need a
M851 X0.0000 Y25.0000

 

Update 11/04/2022

  • New FanDuct and cover
  • New 3D rendering

Update 11/06/2022

  • Modification FanDuct

Update 11/12/2022

  • New FanDuct V3 (The previous fan duct did not ventilate well in the area, the air was scattered all over the place.)
  • Update Cover (Reduction of the height of the cover so that the lighting is wider.
  • Added a part to support BLtouch (antclabs 3.1 or equivalent)
  • Increased sliding height for BLtouch (the TouchMi being by default lower than a BLtouch)

Update 12/11/2022

  • changing the positioning height of the fan duct. It was too high in relation to the nozzle.
  • Modification of support for BlTouch (type antclabs V3.1) Added stability.
  • Provision of Bltouch position information relative to the nozzle.

Update 02/12/2023


Complete redesign of the template. After testing the model for 3 weeks, I had to revise it

  • Changed the height of the carriage, because the Vslot Wheel was touching the parts when printing and was taking them off.
  • Modification of the insertion of the motor, more simple just by sliding it
  • Changed the position of the PCB connectors to wire more easily
  • Moved the Bl-touch to the rear in a fixed position for better stabilization.
  • Enlargement of the cover.
  • Simplification and reinforcement of the model (the reinforcement is due to the fact that the carriage broke after 3 weeks, and that I had the Z zero that changed as I used it)
  • Modified the height of the FanDuct and cleared the front air exhaust of the extruder.

Currently the model does not support the Mi-touch (I will see later to position it correctly)
In the future the model should support the BIQU MicroProbe V1.0 (if possible at the same level as the Bl-touch)

Update 26/02/2023

  • turning the bltouch upside down so that the heat is not directly on the PCB
  • Change blower position so that the air flow is centered at the outlet. 
  • Lowering the Fanduct to 2mm above the nozzle.

Update 03/06/2023

  • Change bl touch position. it's at x 0 and Y 25.
  • More compact model
  • Revised hood.
  • Refocused air flow
  • Revised Fan Duct to better dissipate air around the part.

List of parts needed for the 3D model:

  • Insert with Head, M3X4.8 (4 units, 2 for the fanduct, 2 for the Bltouch)
     

 

https://youtube.com/shorts/Sw0sLYyQCtw

Tagi