MODULITH 165 Classic Drawers - All

Print it, pull it off the bed, slide it in.

One piece, zero assembly. Classic drawers print in one go with the handle built right into the front. No faceplates, no screws, no clips. Pop it off the plate and it is ready to go to work.

Every 165 size, one download. 18 drawers, from a slim 1W-0.5H up to the big 4W-2H, plus 3H in 1W and 2W.

Made for the 165 collection. The 165 drawers pack a lot into a compact footprint and are sized for smaller printers like the Prusa Mini and Bambu Lab A1 Mini.

Soft-close if you want it. Snap in the magnet inserts with 6x2mm or 10x2mm magnets and the drawer pulls itself shut.

Classic or Decor? Classic is the fastest way to fill a wall with drawers. Want swappable faceplates, fancy handles and labels? That is what the Decor drawers are for, and they fit the same cases.

GEN2 is now MODULITH. Same system, same compatibility. The case is the building block: slide in drawers, add a shelf, or hang a door, and rearrange or expand anytime.

WORKS WITH MODULITH 165 CASES

Every drawer slides into the 165 case of the same size:

WANT A SWAPPABLE FRONT?

The Decor drawers are the same sizes and take faceplates and handles you can swap anytime:

DRESS UP THE SIDES

Open case sides look even better with Side Covers:

LET THE FREE PLANNER HANDLE THE DETAILS

Not sure which drawer sizes you need? Build your layout in the free MODULITH Planner and it works out the parts for you, hands you a complete parts list with download links, and generates a step-by-step 3D assembly guide for your exact setup.

👉 Open the free MODULITH Planner →

SIZES IN THIS DOWNLOAD

• 1W and 2W: 0.5H, 1H, 1.5H, 2H, 3H

• 3W and 4W: 0.5H, 1H, 1.5H, 2H

• 18 drawers (v2508)

The Hardware folder has QuickLocks (print them in PETG), the Bi-Directional QuickLock, drawer stoppers and the 6x2mm and 10x2mm magnet inserts.

WHERE TO PUT THEM

• Under a table or shelf: rails screw in and the cases slide on

• On a desk: the MODULITH 165 Tabletop Starter Kit builds a freestanding stack

• On the wall: the Wall Mount Kit Lite holds cases on almost any vertical surface

WHAT YOU'LL NEED

A 165 case in the same size. That is it. No screws or faceplates needed for Classic drawers.

• Filament: PLA or PETG (paid links)

• Magnets (optional): 6x2mm or 10x2mm (paid links)

As an Amazon Associate I earn from qualifying purchases.

PRINT SETTINGS

• Recommended filament: PETG, PCTG, or PLA

• Supports: None

• Perimeters: 2-3

• Nozzle: 0.4mm

• Layer height: 0.2mm

Every part is oriented ready to print. The drawers include little helper disks for bed adhesion: peel them off by hand or turn them off in your slicer.

Big drawers near the edge of the plate: clean the sheet, keep drafts away, and let the plate cool before you pop the drawer off. A little Nano Adhesive helps too (paid link).

INSTRUCTIONS

🔧 MODULITH instructions → Start with Connect cases and drawers for QuickLocks, stoppers and magnets.

SUPPORT MODULITH AND UNLOCK MORE

Join the Jerrari Club for member-exclusive models and early access. Every membership helps fund new MODULITH releases and free tools like the Planner. Or pick up a premium faceplate collection for your Decor drawers.

NEW TO MODULITH?

🎥 Watch the system overview:

UPDATES

2026-10 - Page refreshed for MODULITH (formerly GEN2).

Magnet insert update - The new magnet inserts replace the old magnet slots with a more reliable, universal design.

This model is licensed CC BY-NC-SA 4.0. The Non-Commercial part refers specifically to selling prints. You’re absolutely welcome to use my designs in commercial environments, I actually encourage you to use them anywhere you see fit! 👍