LayersFactory
Zgłoś model
1 / 3
Galileo 2 (G2E) Filament runout sensor (UPDATED) [Filametrix and ERCF compatible] — zdjęcie 1
1 / 3

Galileo 2 (G2E) Filament runout sensor (UPDATED) [Filametrix and ERCF compatible]

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Alia5

Alia5

@Alia5_155893

Remixed Galileo2 extruder (G2E) main body for a runout-sensor. Filametrix compatible

Ocena
5 / 5
Polubienia
199
Pobrania
942
Wydruki
12
Wyświetlenia
7793
Oceny
12

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Voron Parts & Upgrades
Licencja
GNU General Public License v3.0
SzczegółyPliki (8)Wydruki i komentarze (Wydruki: 12) (Komentarze: 46)Remiksy (3)Kolekcje (342)Powiązane

Galileo2 (G2E) with filament runout sensor.
 

- ECAS-Fitting compatible.
- Step file included.
- No change in overall G2E dimensions

BOM:
 

  • 1x Omron D2F microswitch
  • 1x 5mm steel ball bearing
  • (optional) 2x M2x8 self tapping screws
     (You might get away with M2x10 and some shims, I did.)

Assembly instructions:

  1. Carefully bend the pins of the microswitch flat (but not fully against the housing)
  2. solder wires to the outermost pins of the microswitch
  3. insert a 5mm steel ball into the hole
  4. insert the switch into its mounting place
    you may need to depress the microswitch while inserting.
  5. IMPORTANT STEP: slide in some filament and check if the switch actually got depressed.
    If not: Flow some solder on the “backside” of the switch connectors, tightening the fit.
       This way, you can easily tighten the fit if the tolerances are too large on your print.
  6. (Optional): Secure the microswitch with some glue or screws.
  7. Update your Klipper config.

Example printer.cfg

 

########################################
# Filament runout switch sensor
########################################
[filament_switch_sensor runout_sensor]
pause_on_runout: True
runout_gcode:
    SAVE_GCODE_STATE NAME=runout_state
    G90
    G1 X350 Y358
    G91
    G92 E0
    G1 E-60 F300
    RESTORE_GCODE_STATE NAME=runout_state
insert_gcode:
LOAD_FILAMENT


pause_delay: 0.5
switch_pin: PG11

BE WARNED! This works on my Voron 350 with an SKR Octopus board. and a Revo Voron Hotend. If you use it, do so at your own risk, and update what's needed so it runs on your printer. I will not be held accountable for any damage to your printer caused by your own actions.

Changelog: 


- 02.04.24
    G2E was officially released.
    I remodeled the file based on the officially released G2E Cad. (V2)

- 03.04.24
    Added a Filametrix filament cutter compatible version

  • Filametrix version needs a bowden tube before the heatset, cut to length, insert and check, lock in place with heatset
  • Yes, ERCF works absolutely beautiful with just a filament entry sensor in the toolhead.
    I didn't see a second sensor that useful as we mostly print without an MMU anyway, so why the overhead?

Tagi

filament2sensorrunoutvorongalileostealthburnergalileo2g2efilametrixecrf