MODULITH 185 Decor Drawers - All

Pick a drawer, then make it yours.

The front is up to you. Decor drawers take swappable faceplates and handles, so you can change the look anytime without reprinting the drawer. Print the body in budget filament and save the fancy stuff for the faceplate.

Every 185 size, one download. 18 v2609 drawers, from a slim 1W-0.5H up to the big 4W-2H, plus 3H in 1W and 2W.

Tear-away front. A support panel holds the drawer front dead straight while it prints, then snaps right off. Every size gets one, so no more separate edge supports.

Small parts stay put. The holes in the side walls now print filled in with a pop-out, so tiny bits do not sneak out the sides.

Made for the 185 collection. The 185 drawers give you solid storage volume and still fit the widest range of printers.

Soft-close if you want it. Pop in the magnet inserts with 6x2mm or 10x2mm magnets and the drawer pulls itself shut.

GEN2 is now MODULITH. Same system, same compatibility. The case is the building block: slide in drawers, add a shelf, or hang a door, and rearrange or expand anytime.

WORKS WITH MODULITH 185 CASES

Every drawer slides into the 185 case of the same size:

FINISH IT WITH A FACEPLATE

Every Decor drawer needs a faceplate on the front, and you can swap styles anytime. The Classic series is free:

EdgeLabel is the most popular:

More styles: Essential · Classic Pro · Chevron

WANT GRIDFINITY INSIDE?

Same outside size, with a full Gridfinity grid in the floor:

DRESS UP THE SIDES

Open case sides look even better with Side Covers:

LET THE FREE PLANNER HANDLE THE DETAILS

Not sure which drawer sizes you need? Build your layout in the free MODULITH Planner and it works out the parts for you, hands you a complete parts list with download links, and generates a step-by-step 3D assembly guide for your exact setup.

👉 Open the free MODULITH Planner →

SIZES IN THIS DOWNLOAD

• 1W and 2W: 0.5H, 1H, 1.5H, 2H, 3H

• 3W and 4W: 0.5H, 1H, 1.5H, 2H

• 18 drawers (v2609)

The older v2602 and v2508 drawers are still in the download in (LEGACY) folders. The Hardware folder has QuickLocks (print them in PETG), the Bi-Directional QuickLock, drawer stoppers and the 6x2mm and 10x2mm magnet inserts.

WHERE TO PUT THEM

• Under a table or shelf: rails screw in and the cases slide on

• On a desk: the MODULITH 185 Tabletop Starter Kit builds a freestanding stack

• On the wall: the Wall Mount Kit Lite holds cases on almost any vertical surface

WHAT YOU'LL NEED

A 185 case in the same size and a faceplate for the front. Some faceplate and handle styles use M3 screws, so check the faceplate page.

• Filament: PLA or PETG (paid links)

• Magnets (optional): 6x2mm or 10x2mm (paid links)

• M3 screws: stainless steel or steel (paid links)

As an Amazon Associate I earn from qualifying purchases.

PRINT SETTINGS

• Recommended filament: PETG, PCTG, or PLA

• Supports: None

• Perimeters: 2-3

• Nozzle: 0.4mm

• Layer height: 0.2mm

Every part is oriented ready to print.

INSTRUCTIONS

🔧 Step-by-step assembly instructions →

SUPPORT MODULITH AND UNLOCK MORE

Join the Jerrari Club for member-exclusive models and early access. Every membership helps fund new MODULITH releases and free tools like the Planner. Or pick up a premium faceplate collection.

NEW TO MODULITH?

🎥 Watch the system overview:

UPDATES

2026-10 - v2609 Decor drawers: every size now prints with a tear-away front support panel, and pop-outs fill the side-wall holes. The v2602 drawers move to a legacy folder.

2026-10 - Page refreshed for MODULITH (formerly GEN2).

2026-05 - v2602 Decor drawers. The v2508 drawers stay in the download as legacy.

This model is licensed CC BY-NC-SA 4.0. The Non-Commercial part refers specifically to selling prints. You’re absolutely welcome to use my designs in commercial environments, I actually encourage you to use them anywhere you see fit! 👍