Liczymy pasujące modele…
Se below for update (V5) For this model you will also need 4x M3 heat brass inserts and 4x M3x12 hex screw I print mine in PETG 0.4 nozzle 0.3 hight 3 layers and 25% cubic infill Drill the holes with a step drill as needed on work sight,…
A little support is needed but comes off quite easy
Note !! this is a remix however I cannot find the source any longer. The model is possible to screw to almost anything , it has a groove in the top to storrage a special size drill if needed and have 2 slots in the top for center drill…
Print in PETG and keep the walls plentyfull. Enjoy and happy printing
Scale to your need and send it in your filament of choice.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
A little sanding is needed in the end.
Note there is several models mixed into one here also this model https://www.printables.com/model/209006-philips-oneblade I printed mine in PETG 0.4 nozzle 0.3 layerhight with 3 walls and 25% cubic infill Enjoy !
I printed mine in ASA and used CA glue but I will think that most materials is fine for this aplication. Enjoy !
Made mine in PETG but ASA will properly be better with the direct sunlight and all. 0.4 nozzle 0.2 layer height and 3 walls 25% cubic infill. Enjoy !
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Weigh our fillament scrap and multiply 1 Gram each….just send it :-)
Well I used PETG and that works fine also. Print hot and with a lot of walls and it will fork fine.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Printed in PETG with max amount of walls 0.4 nozzle and 0.2 layer
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
My printing settings : PETG 0.4 nozzle 0.2 layerheight 2 walls and 15% cubic infill . No support anywhere, very print friendly , ad a little glue on the top and thats it. Note photo is my first “little” model, STL files is scaled to 150%…
Did mine in black Spectrum 275 ASA filament with 0.4 nozzle and 0.2 layers hight, no support and 6 walls.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Well just a 30mm spacer for the top (print 4) and some caps for the M3 hardware uses 20x M3x40 hex screw. And the feet , print in TPU (print 4)
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill. Horsepower gain of minimum 2Hp ……(sorry but had to make that joke)
PETG or PLA will work fine but keep 0.2 in layer height. Enjoy !
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
PETG : 0.4 nozzle 0.2 layers 3 walls and 25% Cubic infill
I made a more printer friendly base and some fixed posts so with good settings minimal support is nedded. PLA or PETG and 0.2 layer height will work just fine. And Yes I do not ride Yamaha ;-)
I recommend PETG 0.2 layer height, 0.4 nozzle, 3 layers and 25% Cubic infill Personally I use one for a mix of heat inserts and nuts and bolts, screws ect. to messure on while im designing stuff. Happy Printing !
Note its a bit too tall to be printed on a Prusa MK3! I printed this one on CR10 Max with PETG Note it will fit the normal Nitril gloves box with 100 in like Semperguard and more in the same style box. Enjoy !
Printed in TPU varius brands and for the most part it comes out nice …tricky thing that TPU :-)
Just created a bit of wall art for my garage.
My printing data : PETG 0.4 nozzle 0.2 layer height 3 walls and 25% cubic infill Advise: Print several using sequential printing , when you have them in stock you will use them more for your projects and they are more easy to design stuff…
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
I print mine in clear PETG but most materials will work just fine.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Not a demanding print if you keep it in 0.2 layer height and 3 walls with 0.4 nozzle however it takes a lot of time :-) Cap ring and logo is glued on the cap. Note that if you need brown transparent PETG filament PM is the one I found…
I printed the male part in TPU and the female part in PETG , and has worked for several years now -10 to +30 degrees no problems. Happy printing !
Scale to your liking and insert colour change in your slicing and just send it. I uses PETG but anything will go here. Happy printing !
9 times out of 10 times you need a tool to remove the filter from a faucet ,with this tool nearby stops you from running to the workshop every time to grab a dirty tool. Go with regular PLA on this item and keep the walls plentyfull.…
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
I made this in PETG with 0.4 nozzle 0.3 layers 3 walls and 25% Cubic infill and then I found 2x drywall screws in the workshop , thats it, so simple it almost hurts :-) Note this is made for a Ford Fiesta 2005 but will fit many car…
Hack up your allen keys , heat key up and insert into handle.
Printing data : PETG 0.4 nozzle and 0.2 layer 3 walls and 25% cubic infill just cut up some foam filter to size and thats it.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
This tool will give you a stabil sufrace to sand prints on by draging your prints over it to eliminate small amounts of warping and small amount of remaning support, glue preparing , and give your fit and finish that extra pro part feel.…
PETG and so many walls that the thing is solid ..and just send it.
If you want to copy my hammer here is the settings and stuff I used to make it. A+B part PETG 0.4 nozzle - 0.2 layer height 20 Walls and top and bottom 50% Cubic infill C part TPU x2 3 walls and top and bottom 50% Cross Hatch infill 3x…
TPU with your own settings ..you know your printer and filament best ! Enjoy !
I printed mine in ASA and used CA glue but I will think that most materials is fine for this aplication. Enjoy !
Please look at the several STL files , I plan to upload more in the future. Note that the feet can be mounted from the both sides (if needed at all) also note that all the OEM Biltema accessories will fitt. Enjoy !
Hope they are usefull to you. Enjoy and happy printing !
Here you have 12 hooks in the STL file Printing: PETG 0.4 nozzle and 0.2 layers and 25% cubic infill and minimum 3 walls
These are mounted on all the covers in the rear of the van. I do not advise PLA (hot in the van) , But PETG with a max amount of walls is the way to go. Happy printing and fixing !
Ford Fiesta MK7 Rally keyring Most materials and settings will be fine for this print
Parts on model is a bit tight directly from buildplate with PETG however its not too tight and will free up fast when in use.
PETG 0.4 nozzle 0.2 layer hight and 3 walls 25% cubic infill Happy printing
Very print friendly as is, and good base for remix if thats your thing. I see a tray with this model and Jawbreaker candy in the cavity..well something like that , or perpaps mounted on the wall with a knife / sword. Or play a prank on…
There is 2 STL models V1 was found to be not a organic shape so was rejected :-) I printed mine in PETG 0.4 nozzle with 0.3 layer hight and 3 walls 25% cubic infill. Note that PETG is flammable so use at your own risk and please do not…
I printed mine in PETG with 0.2 layers 4 layers and 25% gyro infill.
This model will give you a straight filament path to extruder. don't believe everything you see on youtube , Igor must have seen it but failed to mention it somehow 🤔, even if its fliped 180 degree its not in a straigt line but better and…
Made In PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Print with support (I use snug) and throw in 2 x M3x10 screws as in photo. Note that handle taps on drawer print without support so setting need to be accordingly. Enjoy the model and your superracer …I do :-)
Made mine in PETG 0.4 nozzle and 0.2 layer hight 6 walls and 25% cubic infill.
Used Azure PETG and 0.1 detail with 100% infill and 10 layers, no support, no brim…nothing worked like a charme in the first try :-)
Will fit following 120mm vise types (and perhaps more brands) Ridgid Peddinghauser Superior Matador MOB Durlach Printning: PETG 0.4 nozzle and 0.2 layers and as many walls as possible is my advise. Happy Printing !
Remix of Egg cup by Chiffe Printing (My settings) : PETG 0.4 nozzle and 0.2 layer height 5 walls and 25% cubic infill and “fuzzing” to outer walls.
Printing data : PETG 0.4 nozzle 0.2 layers 3 walls 25% cubic infill. Enjoy your print and coffee :-)
Everybody lowers the spool , and that makes sense , but filament sensor is not in center of spool, this print will take it a bit further to the center , not perfect , but wires is not any longer :-) uses 2x M3x35 hex bolts (40mm with some…
There are many can holders out there but many of them is not usable for mechanics on the move because they do not “hold” the can and stop it from ratteling around in the car / truck. note there is a small recess on the backside for dubble…
Scale this to your need Warning : 3D printing is not food safe in general , but if you want to challenge your health I advise you to print with PETG 0.4 nozzle 0.2 layer hight and 105 walls. Hope you found my model usefull , please upload…
WARNING: This is plastic do NOT tow anything you cannot afford to lose like kids , dogs and so on, this is at your own risk…. AND Please do not go 90 with it ;-) My printing data :PETG 0.4 nozzle 0.2 layer height 6 walls and 50% cubic…
I have no intention to print this in real life due to the cost of filament , however maybe someone will make this the base for a cool personal stand. You will need a 350mm size printer The MX Stand is 440mm high , split on the middle more…
Made part A in PETG with 6 walls top and bottom 50% cubic infill , Part B was made in PETG-CF with 10 walls 6 top and 6 bottom (solid) Note part A needs some support , I did go for tree support and 20 degrees in Bambu slicer Seems very…
Print in cheap generic TPU 😆 4 walls/top/bottom 25% cubic infill Enjoy !
Like all the other ones , glue a magnet to it and slap it on there.
Scale it to your need.
Used Colorfabb XT-CF20 25% infill and 3 layers , used M3 brass inserts and 2 x M3x10 Unbrako stainless bolts, came out great !
Not mutch to say , its a sign. Print in PETG or ASA for outdoor durability (ASA is the best choice however I made mine in PETG) 0.4mm Nozzle and 0.2 layer and 3 walls and a color change from 2.2mm to 3mm Happy printing
Nobody wants a half dead mouse because og side entry to the trap , this item will make a springtrap more humane, scale mine to fit your springtrap or design your own. Protip : the box is so deep so its possible to store bait, nuts or…
Printed mine in PETG 0.4 nozzle 0.3 layer hight and 3 walls, 25% cubic infill Note that the model is so its easy to grab the needed collet because of the angle of the holes. Happy printing !
Printed in PETG 0.4 nozzle 0.2 layer (spacer in 0.3) height and 3 walls 25% cubic infill. Happy printing and fixing stuff !
Will probaly fit in with your pencils and markers by your desktop and assist you in several prying jobs as time goes by. I have several Knipex tools in the area also hence the color scheme on mine. Made mine in PLA , 10walls 10 top and…
BOM : 4 x M5 heatset inserts and 4 x M5x20 hex bolt , I also use 2 x M6x25 hex bolt inside the red bolts (threaded and glued in for max strenght) but it will work just fine without. Clamp part: I used PETG-CF with 8 walls, top and bottom…
Filament of your choice, any will work just fine. Note that the model has a room for 25mm VHB tape on the back. Simple model and the remote will be usable in from the holder aswell Just wanted to share since there is no point that we all…
To wszystkie aktualnie dostępne wyniki.
