Liczymy pasujące modele…
Just made this in case you want to replace the logo on your box with one that matches your box better I drew the logo from scratch doing my best to make it exactly like the original one so it's possible it's not 100%
My brother wanted a Mesa/Boogie logo instead of the Marshall logo
Two piece handle for Series 25 (25mm / 1in) Aluminum Extrusion Uses two 16mm M6 flathead screws Included step file incase you need to make changes. My hards are on the small side. I printed it upright, and on the side. And I think the…
Two piece handle for Series 40/15 (40mm / 1.5in) Aluminum Extrusion Included step file incase you need to make changes. I printed it upright, and on the side. And I think the side comes out better. I used tree supports and a brim when…
Simple model to hold 10 SIS or similar sports gels. It has some inner structure too so they stand up even after you take a few out. I could never tell how many were left in a box, and they didn't really stack well or anything in other…
Simple tool for screwing in SMA cables by hand. No supports needed
Prints fine upside down without any supports Tested in PLA but probably longer lasting in PETG because it snaps in This attaches to the pegboard using cleats so it can securely attach to the pegboard. Why? Well when I would remove some of…
Use 3x6mm magnets. The hexagons holes allow you to get them out more easier if absolutely needed. But you do need to hammer/press them in. No glue needed. Printing This was able to be printed with the top of the model down on the build…
Updated version here: The design is inspired by the PBSwiss holder, but I didn't like how big it was and I also don't need the giant screwdrivers often so they went in a drawer. The holders have a space for a 3x6mm magnet - It's not…
Prints fine upside down without any supports Tested in PLA but probably longer lasting in PETG because it snaps in This attaches to the pegboard using cleats so it can securely attach to the pegboard. Why? Well when I would remove some of…
Use 3x6mm magnets. The hexagons holes allow you to get them out easier if absolutely needed. But you do need to hammer/press them in. No glue needed. Printing You do not need supports for the hexagon hones, this was able to be printed…
This spool snaps around the Shimano Di2 SM-BCR2 Charger to make it easy to keep stored when not in use When you install it, make sure all the cables have room because the charger is not symmetrical in any orientation and it only works one…
The holder slants to minimize how much it sticks out so there are two versions - One if you have it on the left side of the board and one if you have it on the right side of the board. Uses a total of 14 (Sorry!) 3x6mm magnets. 1 or 2 on…
This attaches to the pegboard using cleats so it can securely attach to the pegboard. Why? Well when I would remove some of my tools, the holder would come out with it. The video explains a lot of it. I was able to print this without…
Use 3x6mm magnets. The hexagons holes allow you to get them out easier if absolutely needed. But you do need to hammer/press them in. No glue needed. Printing You do not need supports for the hexagon hones, this was able to be printed…
These are redesigned versions of my old holders. I wanted something that was more uniform and looked better being printed. And I wanted them to be easily removed and put back. My old design required me to lift them up before pulling them…
This attaches to the pegboard using cleats so it can securely attach to the pegboard. Why? Well when I would remove some of my tools, the holder would come out with it. The video explains a lot of it. I was able to print this without…
Just added a 10mm hex (slightly smaller so it fits better) to cmh's design so it sits easier in my cannondale cranks
Keep your Park Tool Threadlocker bottles from tipping over in your drawer with this holder. Space for magnets on base to keep it upright even when you slam the drawer. The hexagonal holes take 3x6mm magnets - They press fit very very…
I couldn't find an accurate SPD cleat blank for making a fixture I needed so I made one. I printed a jig with this where I made the opening 0.125mm bigger and it slides on perfectly but doesn't move. This won't work with the Silca…
Allows you to mount your Qingping Air Quality Monitor against a window (using double stick tape) so you can see the readings from outside. I use this to see the readings inside my printer case when printing things like ASA. The case has…
Holders for the insertion and extraction tips available from McMaster Carr. Yes, a lot of them are duplicate parts but in a big lab with shared resources it's nice to not have to think about what tip to use. I printed them on their sides…
To wszystkie aktualnie dostępne wyniki.
