Liczymy pasujące modele…
I dropped one of my screw boxes and had to return this mess of screws and dog hair back into something usable. Measuring each single screw turned out to be a time comsuming pain. So this idea of a credit card sized tool turned up. You can…
For hoses with 100mm inner diameter. No support needed - print as shown.
These are potentiometer knobs originally designed for Korg Synthesizers (Minilogue, Monologue...) but will fit on any other standard potentiometer. There are 2 designs to choose from: design 1 resembles the original knobs design 2 is a…
See an updated version at: https://www.printables.com/model/259313-airsuck-2000a-standardized-version-von-airsuck-200 Please note this disclaimer: ------------------------------------ This is a quite large fan with blades rotating at high…
The screen i made it for is a Hmtech 7" LCD without touch function: https://www.amazon.com/HMTECH-Raspberry-Pi-Monitor-Non-Touch/dp/B09MFNLRQQ It may fit other generic displays too if the front of the screen is 100x165mm. The screw holes…
Updated 05/2024: Some fixes, new rotor for extruder feeder as coupler. Also added part variants for a half height version. All Parts are interchangeable with the old version. This is a standardized version of my previous “Airsuck 2000”…
An empty reel for a Reel 2 Reel Tape Recorder. Size changed to 13cm / 5inch Print Settings Printer: Renkforce RF500 Rafts: No Supports: No Resolution: 0.2 Infill: 35% Filament: - - Category: Audio
To retrofit my old light installation i wanted to use the Tapo smart button as a light switch replacement, but i didn't want to remove the original light switches. So i made this light switch cover/base plate which will hold the button…
YL-69 case redone for a tighter and stable fit. Please use 2 pcs. 2x6mm screws to mount as shown in the photo. Also added a case for the YL-38 comparator. Needs another 2x6mm screw to fasten. Category: Electronics
Print as shown without support. The 18650 version is an afterthought and will most likely only allow a battery every 2nd slot. This is due to my goal for interconnectability/stackability between the variants. I tried to make all variants…
This remix is based on GrafXP s excellent Modular Rack System for Gridfinity Drawers (thanks for sharing also the .step files!). If you want to know more about the rack system, please visit the original author's page! Please note, that…
I'm not sure what they are called in English...in German they are called "Backenschoner" or "Schutzbacken". They exist in many variations. This variation here will nicely fit on a small Proxxon vise and not only hold the workpiece in the…
Had a small pump left over from an indoor fountain and some low quality filament to use up - so i created this little indoor wishing well with Tinkercad and Meshmixer. The beautiful ornaments are a remix from user poggia10. Assembly is…
I use them for organizing cords while camping etc.
Wanted a dust cover for my Korg Volcas - ended up with this thing where you can store them easily as a stack. There is no need to remove the shroud if you are using them. I found it convenient to leave them on as a hand rest and it also…
I needed a housing with fan for a voltage regulator. So, here is one. The housing fits a "XH-M411" (at least that's what is printed on the bottom of the circuit board) Amazon Link:…
(English below) Austauschspitze für Blindenstock: Für Kugellager mit 16mm Durchmesser 2 Varianten: M3 oder M4 Madenschrauben zur Befestigung (original ist M3 aber bei M4 zerstört man nicht so leicht das Kugellagen beim Befestigen) Als…
Made for small 360 cameras up to approx. ½ kg. Designed to filter out vibrations, e.g. induced by subwoofers. It was a makeshift solution born out of necessity within a short timeframe but turned out to work quite well. Please note that…
For "cigarette lighter"-style sockets. Print as shown - no support needed.
This is a simple and robust housing for a KFB 2.0 Controller. It will coincidentally fit as a controller housing on a Renkforce RF500 (it was originally designed with this printer in mind). Measurements: housing approx. 114x149x75mm (with…
The plate was missing on my Beta, so i made one which resembles the version i have seen on several other ones. Print only part 1 for single color, or use both for dual color. Mount (glue) it in front of the gear stick.
This part is prone to break on all Lancia Betas the white one) This specific one is modeled for the first series. You may need to slightly adapt the narrower part for fit with a file as the available space is very limited.
This is a 3d printable mock-up of the broadcast tower Linz Lichtenberg operated by Big Blue Marble Austria (former ORS) at a scale of 1:100. The real tower is a steel tube mast with a height of 155m, so the assembled model is roughly 1.5m…
To wszystkie aktualnie dostępne wyniki.
