Liczymy pasujące modele…
Simple tool to help keep the baffle stack aligned when assembling the Rugged Oculus 22 Suppressor. PLA should be fine and I printed with a brim to help with bed adhesion. Then just de-burred the brim area . I used 100% infill with 4…
Mil Spec AR15 buffer tube vise block. Printed in PLA at 98% infill for strength so the buffer tube will not twist while tightening the castle nut. The fit is very tight on the buffer tube, but the plastic seems to be plenty strong.…
This is a drawer for an Ender 3 s1 that holds a Raspberry Pi 4 B, and still has a small storage bin at the back. The loop inside is to zip-tie the power cable for strain relief. I found the base drawer on another site, but it did not line…
Simple box that will store a CMMG .22 conversion bolt or an AR15 bolt while the conversion bolt is in use. Lid slides on and off easily. Added a separate file for a lid with raised letters. The raised letters seem to print cleaner for me.…
The Velcro for the soft shell holders is just a square sheet and does not fit the receiver properly. This allows me to use a silver sharpie to mark the back of the Velcro so I can cut it to fit the receiver (even leaving a cutout for the…
I removed the factory subwoofer and installed an aftermarket one in the center console of my 2002 Jeep TJ (Wrangler). After doing that, the factory cubby in the center console was too deep, so I needed to replace it. The factory one also…
When mounting a SeeStar S50 to the Sky-Watcher EQ base, the knob to tighten the dovetail block to the EQ mount will not fit because it hits the bottom of the S50. Many videos show using a long bolt to move the knob out from under the S50,…
This is a replacement front cap tool for the Rugged Oculus 22 suppressor. If you lose the original, or just want a better fitting design, this one works. I printed it in PLA which should be fine as long as you don't use it when the…
Small bin and lid made to fit in the unused area of the under hood fusebox in a 2002 Jeep TJ. I used it to store spare fuses in a small Altoids tin. The main box body is printed in PETG-CF for heat resistance and the lid is TPU so it is a…
Little plastic clip that keeps the internal door lock/latch bar attached to the internal door handle on a Jeep TJ (probably a lot of other cards as well). All of the ones I found at the auto-parts store would not stay connected so the…
This is a remix so that real 9mm MP5 or clone magazines will fit. Holds 10 real or clone correct 9mm MP5/SP5 magazines. There are cutouts in the bottom for Qty:6 20mm x 3mm magnets, but I realized it only really needed 4 magnets to stick…
This allows you to use a 24mm Deep socket to install/remove a Tri-Lug muzzle device. This fits over a Tri-Lug muzzle device and inside of a 24mm socket, then use a torque wrench to install to required torque per manufacturer. I printed it…
Simple box for storing cleaning wipes for glasses. Has a small bin in the front to store the 1/2 sheet of the lens wipe after tearing off one of the pair. Made to fit the Zeiss lens wipes packets that are approx 50x100mm. Created in…
I took the statement by the original creator that he wanted it to be easily removable form the wall one step further and made it two separate parts. The cup mounts to the HSW securely, and the holder sits in it and can easily be picked up…
I only have two plates and one is always on the printer so six slots on the original seemed to be excessive for me. I don't ever see having that many, so I chopped off 4 of the slots and shortened the back plate to remove the excess…
These are some of the fins (and the little handle nubbin) to replace broken parts in the front air vents of a 2002 Jeep TJ Wrangler. I printed them in Bambu ABS GF which should easily hold up to the heat. The fins all have a flat back…
Storage box for M1a magazines. Will store 6 steel magazines 3mf file is provided in case you want to modify this.
I needed to drill out the gas port on a Ballistic Advantage .308 fluted barrel. This vise block is tapered to fit the contour of the barrel and has a notch cut in it so access to the gas block is easy. Printed in TPU95 it is strong enough…
This is a “gasket” for where the pin in the bottom of the upper door frame goes into the body of the Jeep. It keeps the pin from rattling against the body when the sides of the soft top are off. This was made to fit the 2002 Jeep TJ with…
This is a hanger for a 3oz Brass hammer. https://www.amazon.com/dp/B0058EDQ9K?psc=1&ref=ppx_yo2ov_dt_b_product_details Requires the use of an empty insert from: https://www.printables.com/model/152592-honeycomb-storage-wall I printed it…
Storage box for Breathe Right Nose Strips. Designed to hold two of the 70 strip boxes from Costco. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter Supports: No Infill: 20 Category: Containers
Eye Loupe holder for the Honeycomb Storage Wall system (HSW) Designed for a loupe with up to a 38mm base. Requires a HSW instert to mount to the honeycomb like this:…
This mount allows you to install a JBL BassPro Nano subwoofer and a Midland MXT 275 (maybe other MXT models as well) under the center console of a 2002 Jeep TJ/Wrangler. Subwoofer:…
The Mazda 6 (2014-19) with the automatic transmission has a common failure in the shifter park position sensor. The rubber nubbin on the end of the sensor wears down such that the car will not shut off because it thinks it is not in park.…
To wszystkie aktualnie dostępne wyniki.
