Liczymy pasujące modele…
Plastic cover replacement for the jacking point hole in the side skirt of a Ford Fiesta MK6 ST150/XR4 2004-2008. There is one version for front right (FINIS 1354162) and one for front left (FINIS 1354166). It is not an exact replica but a…
The Asus PRIME X670-P requires a special mounting bracket to vertically mount a WiFi card. While the manual states "The M.2 Wi-Fi module and vertical M.2 Key E bracket set are purchased separately.", it can (currently) not be purchased.…
The Temset radiator uses a valve for which no adapters seem to exist. But for the installation of an eQ-3 eqiva thermostat, an M30x1.5 thread is required. The adapter makes it possible to install such a thermostat but the pin of the valve…
The EAP615-Wall (as the name suggest) is meant to be mounted at a wall. But for our purposes, this wall mounting was no option and the device had to be placed on a desk or other furniture. It is printed in two parts which have to be…
To measure the distance of the toolhead to the mesh for the klipper bed mesh (compensation), you need a probe like an BLTouch which needs to be mounted to the toolhead. I've switched from the original Qidi Extruders to humebeam 's Icarus…
The Brötje radiators use 4 plastic clips (2 on each side) to hold the metal side panels. They have to be attached to two pipes inside the radiator. They are rather tight and tend to break when removing one site panel for cleaning…
BerHerJohLin's ESP32-CAM-MB is a nice, modular design - but currently only for the Pipersberg G4 RF1 c. Only the part which attaches to the gas meter needs to be replaced. In this case, it was replaced with a part for the Elster BK-G4 MT…
If you want to switch your Qidi X-Max (1) from the (slightly frustrating) original firmware to Klipper, then the original touchscreen cannot be used anymore. But it is possible to use other touchscreens on your the RaspberryPI (which runs…
There is a large list of radiator fan mounting models Alvomane's Radiator Booster UppsalaHenrik's 2x92mm fan ducts for radiator djtifosi' Radiator Blower Fan with magnetic holder simlrh's Radiator Fan schranzistor's Radiator amplifier…
To measure the resonance for the klipper resonance compensation, you need a RaspberryPi + an ADXL345 which needs to be mounted to the toolhead. I've switched from the original Qidi Extruders to humebeam 's Icarus 2.1 due to massive…
This mount is a design based on the principles shown in the Qidi X-Plus X-Max Octoprint Raspberry Pi Camera Bracket by cwills7 . The design allows the mounting of the Raspberry Pi Camera (C) Rev 2.2 on the top of the door frame of the…
The Carriage Mounted Dial Indicator Holder for the Qidi X-Max is an excellent design by humebeam . It can be used with the original carriage by Qidi. Only the cover, ribbon cable, two screws for the extruder and the extruder itself have…
This mount is a design based on the principles shown in the Qidi X-Plus X-Max Octoprint Raspberry Pi Camera Bracket by cwills7 . It extends my original remix with LED mounting wings. They are aligned with the camera orientation and make…
The Qidi X-Max has enough free space in the electronics "compartment" to mount a RaspberryPi. But it has to be mounted upside down - something which can be done rather easily with self-adhesive Velcro tape. This has the benefit of being…
This mount is based on the basic design shown in the Pololu Maestro 6-Channel Servo Controller Case by KikiTay . The servo controller needed to be mounted next to the actual servo on a (curtain) rod. The hooks were attached on both sides…
Achenbach windows use a small wedge/distance holder to ensure the correct position of the window when it gets closed. The original part from Achenbach is basically only a shell and tends to break after a couple of years (depending on the…
When using no guide or the 50mm radius guide from @Exerqtor_82339, then the reverse bowden tube scratches and drums against the top panel of an LDO Voron Trident 300 Rev.D+ with a Stealthburner Clockwork2 Filamatrix. A 5mm smaller radius…
The access points from Plasma Cloud come with a variety of wall and ceiling mounts which can be clipped on easily. But there was not one a single one which can be used as desk mount. But the orientation can be rather important on these…
The LDO Voron Trident 300 Rev.D+ kits are shipped with handles which can be installed on the ceiling extrusions (on top of 3mm foam tape + 3mm polycarbonat panel). Unfortunately, the boxturtle hard mounts cannot be installed next to the…
To wszystkie aktualnie dostępne wyniki.
