Liczymy pasujące modele…
This is my print and build of the Mondoshawan alien in the movie “The Fith Element”. Great fun to paint and a challenge with metallics. Great job by the creator and thanks for sharing. I have included the .lys file for those using Lychee.
This is a static model of the German V2 Rocket from WWII. Printed as is, it sits at 600mm tall. Parts print in three separate sections. I will be doing a powered version of this model using D & E motors. This is in progress now. The fins…
This is the flying scale version of the V2 Rocket previously published as a static model. The tail section now has mounts for the motor tube mounting rings of which you will need to print x2 of. The motor tube is a cardboard BT-50 tube…
This is an air raid siren built to go inside a Stuka dive bomber model. The Stuka was a German terror weapon used in WWII. As it dived to drop a bomb, a siren would sound out from the plane to terrify the people they were bombing. This…
This is a flying model of the Honest John missile / rocket used in the Vietnam era. The model fly's on E and F rocket motors or just build as a static display model. The model is comprised of 3D printed parts, two Pringles tubes and a…
I resin printed this awesome rendering of a honey bee to about the size of a fist. Then air brushed the model and super detailed it by hand painting. This was printed in one go so it was a challenge to remove supports and paint it without…
This is the cockpit I built for a CARF Models P51 Mustang including the seat, left and right panels and the rear radio stack. It was built using a combination of FDM and RESIN 3D printed parts. The Exhaust stack and instrument panel will…
A set of left and right exhaust stacks for the CARF Models P51 Mustang. The shown examples were FDM 3D printed and textured by stippling acrylic paste with a stiff brush, painted and treated with a technical paint by Citadel called Typhus…
This is a 1/5 scale cockpit for an RC Eurofighter or Euro Sport Jet. The screens and heads up display are backlit by LED's. I will post a photo of the finished item installed in the plane soon. Instructions Print Paint and assemble.…
Dual Scuba Tanks to use as a key ring or in a diorama.
Designed a mount so you can use a dial gauge to get your print bed super level and dialed in. The mount has been made to fit loosely so it can be shimmed with masking tape to get a perfect friction fit on the bar. Bed leveling procedure…
This drop tank can be printed in three parts which are split at a scale seam line. It is 250mm long which is anout 1/8th scale (20cc sized model). It is attached and secured using 10x2mm magnets with two 1/8th aluminium guide rods. this…
This is a 3D printable spool winder if you buy 3DFillies ABS/PLA 1kg rolls and want to transfer it onto an empty UP filament spool for the Up Box. Power is supplied by a battery drill. I have included the .skp files for you to load into…
This design uses 10mm x 2mm magnets. The recesses for the magnets are 10.3mm in diameter to account for the shrinkage of PLA. They press in just right. You will need x5 if you print the scraper as well. The scrapers width is just right…
This is a spacer that maintains a 6mm gap around the outside edge when installing floating floor planking or vinyl tiles
A clip to connect your snorkel to your dive mask with 26, 27 and 28mm inside diameters. Print at 100% infill.
These are the 3D printed parts I created to create the cockpit for a 1/3 scale Boeing Stearman. The plane is a Balsa USA kit and will be powered with a seven cylinder 250cc Moki Radial Engine. Print Settings Printer Brand: Up! Printer: Up…
This is a housing for the Raymarine i70 range of instruments if you want to mount as stand alone instruments. Print 100% infill .20 Drill template has also been included.
Some parts to improve scale looks of the car and also a bigger battery tray for the front that will be a direct replacement. Scale parts are the bonnet grills and a jerrycan. The 3mf file are correctly scaled as well as the grill .stl…
This is the skid plate for the Armortek 25 Pound Field Gun from WWII. Print solid and sand edges round. Print Settings Printer Brand: Up Printer: Up Plus2 Rafts: Yes Supports: Yes Resolution: .15 Infill: 100% Filament: Fillies ABS White…
Scale cockpit for F22 Raptor Instructions Print parts and photo print googled Garmin Instrument Panel resized with Photo Shop to fit printed display. Resize with Google sketchup to suit scale. Category: R/C Vehicles
This is a cockpit with a Garmin Nav screen for the Hanger nine Super Decathlon. This is for the Giant scale 40% model but can be re-scaled to fit any model. If you prefer the version with a radio stack instead of the Garmin, the files…
This is the cockpit I created for the Der Jet DH100 Vampire Jet Model. The files include all required STL files to print the cockpit parts as well as the resized gauge photos to fit the printed dash panel. This will require an advanced…
This 30 degree spacer will fit the Kings Rock Light kit to point the lights downward. Print the screw inserts solid and super glue them in after you have installed the M5 bolts. The insert also compresses outward when the screw is…
Anyone who prints with these machines knows you get resin on your hands and it gets everywhere. This handle will help stop getting resin all over the lid of the machine when you remove and replace it.
This is a small parts container for use in ultra sonic cleaners. I tested a friction fit lid design but the PLA plastic goes soft due to the heat in the ultrasonic cleaner and fails to remain closed. So now I have designed a container…
This is a set of oil Cooler intake fins to replace the kit supplied oil cooler which is very basic and looks substandard compared to the rest of the kit. I have made three of these kits now and fitted one to the centre wing section as can…
Print the off the supplied image of the instruments and glue this to the back of the pane. You can also glue some clear sheet to resemble the glass for the gauges.
This is a cockpit from an Ag Wagon/Fire Bomber. It was made for a large scale RC plane with an actual Jet turbo prop engine. Print Settings Printer Brand: Up! Printer: Up Plus Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: ,15…
These are a couple of templates you can print off to make static grass tuff's for your gaming models. They are used to lay PVA glue down onto grease paper as specific shapes before you apply the static grass with the static applicator.…
This is not my design but a free download from Freewing RC Planes. Print Settings Printer Brand: Up Printer: Up Plus Rafts: Yes Supports: Yes Resolution: .15 Infill: 5% Filament: Fillies ABS White Category: Models
This is a 1/4 scale cockpit dash for a Corby Starlet home built plane. Print the parts and paint as desired, Photo print the gauges once re sized with Photo Shop and tape them to the gauge panel. Instructions 3D Printed with an Up Plus 3D…
This is a heater designed for the Anycubic Mono X and X 6K. It utilizes the original glass filled nylon housing of the 12V PTC 100W heater as I felt this was a safer option due to its heat resistant properties. This isolates the heating…
This is a motor mount that can be used for mounting a 40mm can motor for your RC plane Instructions Just print it Category: R/C Vehicles
This was just an exercise in Solidworks. Vase can be resized in your slicer.
Housing to mount your standard RC switch Instructions Print and mount Category: R/C Vehicles
This is my make of the Randy Cooper design of the MLEV-5 Mars Hopper released by Pegasus Hobbies. The 3D printed content in this article is related to the kit and comprises all the 3D printed parts I am creating for the kit build. This…
As you cannot buy housings for this gauge anymore, I designed a stand alone housing to protect the gauge when diving. I printed it at 95% infill but 50% would be fine. Layer height was 0.2. Printed in PLA.
Replacement IKEA retaining clip for IKEA kitchen stools. They always break but these 3D printed ones don't.
I am building a scratch built R/C PCA-2 Pitcairn which is an auto gyro from the 1930's that had a big radial engine up the front. The parts posted here will help any other builders out there that are planning to build this remarkable…
This is a hard case for the Dekunu altimeter to replace the rubber wrist band type no longer available. The unit simply clicks into place from the back and a stretchy Velcro wrist strap can be attached via the loops on the side. It has…
If your compass cover has disintegrated like mine then you can just print a new one or download the free file and get it. Not sure if this compass came with Macgregors but this is the one that came with mine. Dimensions are I.D = 125mm ,…
Here are all the 3d printed parts needed to make your very own Cockpit from the Spirit Of St Louis. This was the first plane to make a solo non stop transatlantic flight from New York to Paris. The model you see is electric and has flown.…
This is a 3D model of the basic dimensions and clearances for all who want to design their own Pi case for the Pi-3B. This can be used to create you own boxes by making it a component or group it in Sketchup and drawing around it. The…
AOOCI U7 Mounts for CF Moto 450MT plus a mount for the front dash camera
Print with 100% infill. Screw holes have been created at 1mm so they can be drilled out to what ever size screws you decide to use.
This is a hook to stick to your tent light Category: Organization
A magnetic strap holder to replace the useless one that comes with the meter. I found the original rubber strap mount kept comming out of the mount on the meter and the meter would drop to the floor. This mount is in two parts that screw…
Hi All This is a new 3D printable landing gear mount for the E flight Fury. This one is a lot stronger than the original. Print as orientated in the STL file with stable support and a nice hot bed. Mine were printed on the Up Box and came…
Ergonomic mount for the spotlight switch that gives the rider quick access to the high beam switch to dip the lights for on-coming traffic. This mount molds and screws to the bike using the original mounting screw for the indicator…
This is a mount for a standard NARVA battery isolator Print 100% infill .20
Print 100% infill .20
This is a mount so you can use the supplied steering lock on a flat surface. Print Settings Rafts: No Supports: No Infill: 90-100% Category: Other
This is a 20mm leg extension for the DJI range of Quad and Hex arms Instructions Print and fit Category: R/C Vehicles
This is a special spacer to stop the tablet and mount from bouncing around when going over rough terrain. The spacer works by spreading the load over the whole top cross section of the instrument cluster/tower. The 450MT's tower is made…
To wszystkie aktualnie dostępne wyniki.
