Liczymy pasujące modele…
Remixed original for easier and faster printing with no supports. If you plan to store these in PLA, in my experience, the best is to wash and keep some saline solution for a day before you put the contacts. Print Settings Printer Brand:…
It's a single piece duct remixed from https://www.thingiverse.com/thing:5147741/files that doesn't need supports and has a small holder for fan output.
Please see more information in the video. You need to print 3 left and 3 right parts to make the full circle. The outer part is 56cm in diameter when printed. Two versions are available when it comes to thickness which controls distance…
A watch band shortener tool remixed from two designs that requires only a metal pin. In picture a 1cm needle part is used (half of it goes deep inside to keep it firmly) which works really well. You need a base, pusher and a knob. There…
Based on great design from https://www.thingiverse.com/thing:3723481 Changed round holes pattern on the sides to lines as these are easier to print and I find them nicer Increased screw hole holder height so very small screws can be used…
Based on https://www.thingiverse.com/thing:3369418 Made for XCR3D Titan extruder version (which is cheap "optimized" clone version) Very light and simple design to make it perfectly align with hotend To be used with Pancake motors up to…
Overview Simple PC “Server” case that I used for my home media / server PC at home. Every side is printed flat on the bed so it's very easy and fast to print. Size wise it is: 230x170x200mm It supports 2x3.5" or 2x2.5" HDDs, SFX PSU, GPU…
Adjustable adapter for logitech g29 pedals to have them a bit taller and a bit closer. There are two predefined versions of 10 and 15mm (15mm in picture). Original long screws will be reused but you will need two additional short M4…
Based on great design https://www.thingiverse.com/thing:3816051 Very light and simple design that doesn't need support Compared to original, solid print, difference is 11 grams (32 vs 21) which is an obvious plus for direct drive extruder…
Based on a lampshade holder for a bigger lamp https://www.thingiverse.com/thing:3233856 The center is made to perfectly fit a smaller SKAFTET 30cm ikea lamp shown in the picture For this model: Needs support for the central part -…
This is a remix that better fits G27/G29 wheel as it's a bit bigger so it's easier to put and screw on (shorter screw can be used) and has a small 2° angle. It is also made for 20x10x2mm magnets. This all results in a very nice snug fit…
In my case I don't have philips screws on endstop switch and they are thicker so they cannot fit in the hole without drilling so made mounthing holes slightly bigger. Additionaly my inserts have much smaller outer diameter so they don't…
Replacement part for duravit toilet seat from the picture that is slow closing which broke as shown in the separate picture. To replace while mounted toilet seat should be in upright position so it's easiest to pull old one and push new…
This is a mount designed primarily for S21+ phone (might be compatible with others, in the picture there is an iphone 8) that is good enough to keep the phone stable but doesn't cover the monitor / laptop more than needed. It has a bit…
A Neje 30W laser module air assist. (for 40W module see https://www.thingiverse.com/thing:5194498 ) It's a very compact one which still enables access to the focus ring. There are two versions with a 4 and 6mm inner tubing. Both are…
A Neje 40W (A40640) module Air assist. (for 30W module see https://www.thingiverse.com/thing:4843808 ) It comes in two version. 6ID which has inner diameter of 6mm. 6.5ID which has inner diameter of 6.5mm. Height of the laser head should…
The existing rubber on the side of the bin doesn't perfectly close the duct so sometimes it would make the dust skip the bin when you are doing some heavy motions which makes the bin shake. This piece of rubber on the side of the vacuum…
This is a remix for the case cover which enables mounting an HDD 3.5" disk instead of a fan. It also has slightly increased tolerances. It comes in three versions depending on how big your CPU cooler is and how much space you have.…
This is a very small filament guide that can be mounted on compatible printer frames. In my case I use it on Ender 3 frame on the top. Since usual materials are not smooth adding small piece of PTFE tube makes for a great and smooth…
An easy to print PC case which with optimized design for exactly my components. 196x70x320 on front side (CPU, Motherboard, PSU) 170x65x320 on back side (GPU) Hopefully others will also find it useful. Due to flat printing without top and…
This is a remix of many remixes of Ender 3 drawers. It's made to be bigger while still using same amount of filament as original since original was way too small and used a huge amount of filament. It does require additional spacer feet…
This is a ventilation cover I have made for my bathroom system where ventilation is in the pipe and I have a very specific space on the left inside of the tiles but this can be used in general if someone prefers it. You might want to make…
A very short and simple filament guide useful for direct drive extruders. Comes in two versions with and without hole for the filament for easy removal. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Doesn't Matter…
To wszystkie aktualnie dostępne wyniki.
