Liczymy pasujące modele…
This remix aims for a simple CFS-roll system. It won't win a price in mechanical engineering neither in design but its simple to make and requires no special parts. Also no TPU roll or rubber hose is necessary. Differences to original…
See also original FreeCad project file on GitHub: rfid-key-fob.FCStd Note: the real key fobs have high tolerances (see picture).
This duct is an attempt to better guide the air along the heatbreak. It will help to cool down the heatbreak by a homeopathic dose of °C. Because i always want to see the extruder gear moving, i never use the original cover. Even if it…
Tool holder for K2 Plus with brackets.
It started as a naive project and ended in my daily-use frame. Printed with PLA it lasts about 4 months up to a year until it breaks. Given the costs of a few cents i wouldn't care if it break once a month. Probably its a good start point…
CAD model of the go-e wall mount for the Gemini series. See FreeCAD project file on GitHub: gemini-wall-mount.FCStd .
Notes: print bearing cap as spiralized outer contour but sliced with X/Y 102% scale factor dowel: prefer standard 8mm wooden dowel over plastic print (plastic will most likely break at that small diameter) See also the FreeCAD model on…
This case is for Raspberry Pi 5 with Geekworm X1001 (PCIe to NVMe), Geekworm H505 (active cooler), 2280 disk and NVMe passive cooler (i.e. ThermalrightTR-M.2-2280). Requires 4x M2.5x6 Print Layer height: 0.2mm Infill: rectilinear 10%…
Simple vacuum pump adapter for sealing filament bags. It allows me to vacuum a bag within seconds. It basically replaces the shitty battery driven Elegoo vacuum pump. does not require gasket (even printed on PEI bed) Requires decent…
Printing: 2 walls infill 10% Magnets 6x: 3.0x12mm or 2.5x12mm Note: if printed with too less infill, inserting magnets potentially cracks the shell. See also the FreeCAD project file on GitHub: poop-chute-guide.FCStd .
This model is an extra simple bracket to assemble the NerdQaxe+ with 2x 120mm fans and its original power supply altogether. And yes! It looks like a key. :) The fans are intentionally displaced (rear fan is higher) to achieve better…
BoM Thesa MOLL STANDARD (window gasket for grip) Printing walls: 3 infill: 10% Adaptive Cubic PLA works, but i don't know if it withstands a hot summer as hinge pin use 1.75mm filament See also FreeCAD prject file at GitHub: holder.FCStd…
see FreeCad project file on GitHub: doser.FCStd
The M6x40 screw is optional. I was afraid it can become brittle and layer may disrupt. If possible use a nylon nut; don't overtighten. Printing: PETG (PLA is most likely good as well) with the round screw-head pocket downwards 4 walls 4…
FreeCAD project file on GitHub: github.com/…/freecad-course .
Beauty case for mascara, lipstick and other things. no support, 5% rectilinear infill with modifier only until top of bottom, 2-3 walls, 0.1-0.2mm layer height, 0.4mm nozzle, 3/4 bottom/top shells see FreeCad project file on GitHub:…
Smart House for ESPHome sensors Beautifully wraps ESPHome weather station sensors. Solid plug-in system without need of glue or screws. For ESP32 with carbon dioxide, temperature, humidity and barometric sensors. Example application:…
This remix fixes some issues with the original model. It adds the missing project file (now its really open source) and repairs issue with symmetry which originally made it wobble. See open source project file on GitHub: cad/spinner.FCStd…
FreeCAD project file on GitHub: github.com/…/freecad-course .
Yet Another Dosing Spoon The spoon is not intended for liquids, just powder-alike content. Parametrize: download the FreeCAD project file on GitHib: dose-spoon.FCStd . open and modify the properties in settings check the volume in…
Yet another quick and dirty OpenDTU case. This is a very simple box with thin walls and cover has no click system but it does the job. Requires: 1x ESP 32D dev board 1x CMT module with E49-900M20S 2x M2.5x4 Print: infill: 0 walls: 2 layer…
Slightly thicker spacer ring (2.2mm vs 2.0mm original) for cryptex.
no support infill 10% if plastic deforms by time (PLA) , put one wind of painters tape on it See also the FreeCad project file on GitHub: ext-spool-cap.FCStd
layer height: 0.3mm wall count: 3 wall generator: classic infill: lighning scarf seam: enabled skirt, no brim print upside down see also FreeCad project file on GitHub: bit-holder-box.FCStd
This model extrudes the 2D go-e SVG logo. Notes: The .stl export from FreeCad . FCStd project file might have a low resolution if the Maximum Deviation is set to default or too high; set it lower, i.e. to 0.02% : "Edit -> Preferences ->…
Bracket for small Rituals Bottle (70ml). See also FreeCad project file on CitHb: rituals-wall-mount.FCStd .
Floats well, even with insert but it does not have a locking mechanism (will easily get out of place). Material: PLA Printing: FreeCAD project file on GitHub: github.com/…/freecad-course .
FreeCAD project file on GitHub: github.com/…/freecad-course .
I found myself counting screws way too often to not miss any when i am at the seaside. This part organizes all foil screws so that i can see at first glance if something is missing. For Fanatic foil screws, nuts and torx: 5x M8x35 5x…
Sprinkler electronics enclosure for ESP Home (Home Assistant) This project is part of my ESP-Home (Home Assistant compatible) sprinkler and covers just the electronics enclosure. Note : there exist two versions of this enclosure: without…
Minimalistic case for LeMaker BananaPi Pro with WiFi antenna and battery mount.
The only intention of the cap is to slide easily the printer apart without damaging the feet. The original feet are very smooth and stick to well to the table. This cap does not enhance the anti-vibration feet in any way, just makes them…
Yet another wedge for whetstone but this wedge sits rather tight (for 25x50 cross-section whetstone) and can be printed without support. Printing: lay flat side down no supports 3 walls (outer, inner, outer) 7% infill PLA+ Rule of Thumb:…
L-Bracket for Led Clip Recommended Screws 2x 2.5x20 (tight gently, it splits easily) 2x 2.5x12 Printing: no support 2 walls infill 15% See also FreeCad project file on GitHub: bracket.FCStd .
Sprinkler electronics enclosure for ESP Home (Home Assistant This project is part of my ESP-Home (Home Assistant compatible) sprinkler and covers just the electronics enclosure. Note: there exist two versions of this enclosure: with…
FreeCAD project file on GitHub: github.com/…/freecad-course .
FreeCAD project file on GitHub: github.com/…/freecad-course . Following the tutorial i was not satisfied with the shape, hence i choose an alternative approach to obtain a more realistic result: rails are the sides and ruled surface is…
FreeCAD project file on GitHub: github.com/…/freecad-course .
Yet another candle light stand! heptagon base circle top use only with electric candle - fire hazard Parametrizeable Dimensions top/bottom diameter top hole: top/bottom diameter heptagon filet radius top outer/inner and bottom chamfer…
I use this cover to make my doorbell from the 70s fit for Home Assistant. Prerequisite: double sided adhesive tape relais you are willing to sacrifice a rectifier from scrapped electronic (my doorbell receives 12v AC) some cables…
To wszystkie aktualnie dostępne wyniki.
