Liczymy pasujące modele…
Designed to my son after discovering that would be cheaper to print than buy cheap plastic chips from China :D Designed with 0.3mm layer in mind. Here is the source! :D Please be kind! Print Settings Printer: Hypercube Evolution Rafts: No…
Background I was using an inductive sensor as my main Z_min sensor. I was unable to use it as bed leveling sensor because I was using a very thin and soft steel plate under the glass. This lead to several issues: the glass itself is not…
Jojo's "To Be Continued" Arrow redesigned as the one available I had issues slicing. Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 0.2 Infill: 35% Filament: 3DOn ABS Atlantis Blue Notes: May need a brim…
ATTENTION! I RIPPED OFF MY SDCARD HOLDER WITH THE CURRENT DESIGN. BE CAREFULL! I will update it ASAP. I designed this to use with my OpenIPC FVP ground station but the case is generic and the step files allow you to modify it to your…
Facebook discussion group! https://www.facebook.com/groups/275444666421050/ This is a project made with Token47 I would like that Thingiverse could allow multiple owners of a thing :D The main principles guiding the design of this…
Printing recommendations Print with 0.2mm or 0.3mm layer height and at least 3 walls and 4 or 5 top and bottom layers. I recommend at least 30% infill. After printing remove the slots support wall (integrated in the design) as shown in…
A simple 20x20mm square slat, at 45 degrees, with a simple notch to know orientation. You can quickly print them to check and fine-tune your belts at your CoreXY system. In order to do that: 1- Set your X and Y steps/mm to theoretical…
Recently I moved to an apartment that have the number 42. Impossible to live there without this plate fixed below the apartment number. :D Print Settings Printer: Hypercube Evolution Rafts: No Supports: No Resolution: 0.2 Infill: 50% Full…
Remix to use Luer Lok Tip Syringes for the grease injection and M3 hex type screws. The variants are for: LM8UU, LM10UU, LM10LUU, LM12UU and LM12LUU. Not all print tested yet. Updated to M3 screw and increased the syringe fit diameter…
Now you can check if your belts lengths are correctly tuned and check the quality of the single motor movements! The parallel faces are all 20mm apart and there is a small chamfer at the base to cut any problems with elephant foot. Update…
My girlfriend showed me her favorite hair comb one day. She have ir for more than two decades and never found another one like it. With the same size, same teeth pattern, etc. And her, twin, syster had one just like it that she lost or…
I designed this to use with the nice AngelWings Design Pug DLG but it is suitable to any other small glider. Print the propeller blades with 0.1mm or 0.15mm layer height and the other parts are suitable for 0.2mm. 100% infill. Tested with…
This is a device to be used before your extruder that makes it easier to straight, mark and measure with a caliper in order to check and calibrate your extrusion steps/mm. Update: Now there is a hole to put a piece or lenght of 4mm OD…
* Still a work in progress. * I work at a research institute and designed this to help some frieneds to use these e-trash scrap micro stepper motors to move a sample under some experiment at the XY plane. This can be useful for anyone…
This is cap suited for a Brazilian extrusion standard. Compare the drawing to make sure it is compatible with your extrusion. Print Settings Printer: Cliever CL1 Black Edition Rafts: No Supports: No Resolution: 0.2 Infill: 20% Category:…
I got tired of having my idlers mounts always cracking after some use (and abuse). Even the beefer remixes failed with some time due to cracks developing between layers. As an engineer I am aware that the position that the mounts were…
Just print them at a reasonable position, no supports required. Put your capsule at the Base and then the Funnel. Use the Press to measure your coffee and pour into the funnel. A few taps and then press and twist with the Press. Remove…
A basic stand with some hooks that I made for my wife to dry her veterinary surgical instruments. I also used the same design to dry pasta successfully.
A compact printing head with the hotend closer to the movement plane. Have integrated BFPTouch probe sensor hard point (it is compatible with BLTouch too). All fans are mounted at the bracket. Print Settings Printer: Hypercube Evolution…
A friend requested a better way to hold this 11x times magnifier then I designed this holder for him. This magnifier is a really nice thing as it has no visual deformations and it is even useful for carefully evaluate 3d printed parts :D…
Totally new parts with less aggressive bridging. Stil a remix due to the great inspiration and same dimensions as the original :D Print Settings Printer: Cliever CL1 Black Edition Rafts: No Supports: No Resolution: 0.2 Infill: 30%…
A replacement knob for a broken one. The PDF contains the graphics for the switch selector. I just hand draw the prototype and it is like that since :D Print with 0.3mm layer height and 30% plus infill. Added the STEP file for easy…
Simple supports fo fix the Duet Ethernet or Wifi or DueX to a 3030 or 2020 extrusion on my Hypercube Evolution. Print a Pair (as the STL, not like the photos :D) 29/10/2018: V4 Update so standard M5 screws can fit correctly! Removed the…
I designed this to try to overcome the issues with the need to calibrate the sensor different types and colors of filaments. Please follow the discussion and tests being made here:…
This sensor (not my casing, that you can print from here!) is now available from Duet3D! https://www.duet3d.com/DuetAddons/LaserFilamentMonitor * DISCLAIMER: COMPARATIVE TESTING WITH THE REFERENCE DESIGN FROM DUET3D DOES NOT SHOW ANY…
Peça de reposição para jipe espacial Intruder da Usual Plastic do Brasil. Adoro os brinquedos dessa marca. São muito baratos e robustos e aguentam quase toda a violência que uma criança pequena pode impor a eles. Mas não são inquebráveis.…
To wszystkie aktualnie dostępne wyniki.
