20 modeli
This is an upper mount to attach the Wedge RMU Mk3 to the right side of the Original Prusa Enclosure. It uses the tool holder model for mounting. That uses: M3x8 screw (2x) See RMU Mk3 mount for Original Prusa Enclosure (lower) (…
Wydruk około 1,52 €–1,85 € nettoWstępna wycena dla PETGMateriał u źródła: PET
A container for Ring batteries, in the style of Definitive Collection of Battery Holders (Gridfinity, Stackable & Labelled) by xavierly (although this one is not stackable!) It holds two batteries in a 1x2 Gridfinity container. The base…
Wydruk około 4,02 €–4,91 € nettoWstępna wycena jednego wariantu
This is the Mihai esp32-case, but with a countersunk mounting screw hole added to the base. I borrowed the hole design from https://www.printables.com/model/275743-parametrised-power-strip-mount-with-rounded-corner
Wydruk około 1,82 €–2,22 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a lower mount to attach the Wedge RMU Mk3 to the right side of the Original Prusa Enclosure. It uses my Original Prusa Enclosure corner mount model ( https://www.printables.com/model/345660-original-prusa-enclosure-corner-mount/ )…
Wydruk około 1,89 €–2,31 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a mount for the corner holes between two sheet metal sections of the Original Prusa Enclosure. It is not useful in its own right, but it can be incorporated into other models. I've uploaded the OpenSCAD file to make this easier.…
Wydruk około 0,37 €–0,46 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a mount for holding a container of soldering flux on the IKEA Skadis board. It's a remix of the Skadis holder for tip tinner (Thermaltronics, 20 g) by Rai but made bigger. Thanks Rai for publishing the FreeCAD file, it made it so…
Wydruk około 1,26 €–1,54 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This replaces the supplied feet with an adaptor to mount small wheels instead. Each corner uses: M3x12 screw (4x) to attach the wheel M3x10 screw (2x) to mount to the enclosure M3n (6x) The wheel I use is this:…
Wydruk około 0,82 €–1,00 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is a mount for the base of the Wedge RMU Mk3 filament buffer. It is not useful in its own right, but it can be incorporated into other models. I've uploaded the OpenSCAD file to make this easier. For mounting to the RMU base this…
Wydruk około 0,61 €–0,75 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is the Utility Meter Pulse Optical Counter (Home Assistant Glow), with a few additions: A wall mount with an alignment guide The base is 2mm taller, to allow more space inside for wiring A reset pin. Accessing the pin hole is quite…
Wydruk około 1,00 €–1,22 € nettoWstępna wycena jednego wariantu
A stackable container for Ikea Braunit batteries in the style of Definitive Collection of Battery Holders (Gridfinity, Stackable & Labelled) by xavierly It holds two batteries in a 1x2 Gridfinity container. The base OpenSCAD model is…
Wydruk około 3,17 €–3,87 € nettoWstępna wycena jednego wariantu
This is probably the simplest possible model! I needed a simple part to replace part of my front door. Someone else might find it useful as a simple OpenSCAD example. It's sliced for PETG for the UV resistance, and it's ironed on top.
Wydruk około 1,34 €–1,64 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Exactly the same as the original model - but sideways! The sources are also on Tinkercad
This is a mount for holding a Stanley Fatmax 9mm snap-off knife (model 0-10-475) on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need only one nut and the M2.5 hardware to attach it. I use an…
This is a mount for holding a Klein Wire Cutter and Stripper on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. No supports…
This is the original tool holder, but flipped to mount it on the left side of the enclosure. All I did was load the original model into TinkerCAD and click the mirror button. See the original for printer settings and mount instructions.
This is a mount for holding a Molex Hand Crimp Tool on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. No supports are…
This is a mount for holding an Asus ZenWifi AX on the IKEA Skadis board. It uses the Skadis T-Nuts mounting system from 6d6178 . You will need two nuts and the M2.5 hardware to attach them. I use M2.5x16 screws. There are also countersunk…
I used the 3mm longer remix ( https://www.printables.com/model/301787-3mm-longer-body-and-shaft ) of the Ratchet toothpaste tube squeezer ( https://www.printables.com/model/265248-ratchet-toothpaste-tube-squeezer ) but found a bit too…
This is a mount for holding an Engineer SS-02 Solder Sucker on the IKEA Skadis board. It also includes places to store the spare silicone tubes. It uses the IKEA Skådis Secure Clip System Template from mkingery , and a pair of the clips…
This is a horizontal ring with an inner diameter of 18mm for mounting on the IKEA Skadis board. The included freecad file should be parametric enough to create any other sizes required. I use it to secure the end of a digital caliper, to…
To wszystkie aktualnie dostępne wyniki.
