Liczymy pasujące modele…
I was struggling charging my watches and still be able to see / operate them. So I made this stand wich fits the original charging cable (slightly pressed in) - please check attached model dimensions to verify you have the same plug on…
Jig is designed to work with 30mm deep join for 750mm depth of worktop. You can simply do the math for narrowed pieces. Depth of the join is 35mm maximum, for smaller inset depth just offset the jig “to the left” on the pictures Print…
Based on my charging stand for Epix watches, I made this modification for Vivoactive 5 wich fits the original charging cable (slightly pressed in) - please check attached model dimensions to verify you have the same plug on the end……
This part replaces the original Cameo middle feeder rollers, as they're not providing enough pressure to support vinyl rolls and other materials for mat-less cutting. The problem to be solved There is a significant gap between the base…
Mounts between DELL monitor stand or VESA compatible holder Requires new bolts Print instructions PLA or similar stiffness 100% infill 3 perimeters 0.2-0.3 layer height 0.6 nozzle
Holder for cordless drill (tested on Parskide)
This setter can be used on the precision shaft mounted to the chuck on the work piece without dismounting it from chuck (by right V groove on the setter) Print instructions nothing specific Additional parts Threaded inserts for mounting…
You will need two neodynium cylindical magnets (3x6mm) 15 acupuncture needles (0.3x55mm, I used ones with silver handle - just for aesthetic purpose - outermost needle handle is visible through the side of the body) The trickiest part is…
This is the replacement for out-of-the box velcro strips on Syride NavXL vario for easy mounting the vario to the harness or wing risers Print instructions ASA 0.6mm nozzle, 0.2 layer height 3 perimeters 100% infill Additional hardware 2x…
Printed from PLA, two 4mm screws for mounting to the desk / cabinet Print instructions: 0.2 layer 0.6 nozzle 5 perimeters or 100% infil from 3mm height to the top supports (idealy breakaway with 0 top clearance, top interface pattern…
Print instructions 0.6 nozzle 0.2 layer height 100% infil 3 perimeters Print on side Supports required on overhang only Inserts are made of aluminum, use silicon grease
Model is created for 10mm mill and 17mm copy ring Print instructions: PLA 0.3 layer height 0.6 nozzle Bottom thicknes 3mm 5 perimeters Top surface none Infill Honeycomb
Adapter for SW Motech PRO tank ring system to BMW S1000XR 2020+ top-case holder. You need to buy a BMW S1000XR SW-Motech tank ring separately, this is a top-case holder adapter only. Thread inserts are M5+M4 KVT Microbarb Print…
This jig creates 30mm outer radius, with 10mm mill. There are two versions: For the copy ring (17mm) For the mill with copy bushing For any modifications, I'm including F360 parametric file where you can simply modify your desired radius,…
Adapter for milling without portafilter holder
Print instructions 3mm brim 0.6 nozzle 0.15-0.2 layer height 2 perimeters no think wall detection PLA (due to its stiffness) You need 8 5x3x1 neodymium magnet (320g +- magnetic force). Stack them in two pairs. Magnets holding in the slots…
Just a simple baseplate model for Manfrotto tripods, included models are: Plain adapter with no holes, only with slots for male dowels Adapter with hole for M4 Imbus screw Adapter with hole for Tappex Microbarb M4 heat press thread insert…
Limitted by space, moving plotter all around house, I found difficult to have my notebook with cut files connected to the machine. Therefore I made this bracket to fit Alza Ergo https://www.alza.cz/alzaergo-laptop-mount-o30s-d7811299.htm…
DIN rail holders (for 35mm rail) Print instructions PLA (flame retarding filament is suggested) 0.6 nozzle 0.2 layer 100% perimeters or 100% concentric infill Versions Single Double (second relay is rotated 180 degrees for cable mounting…
Print istructions PLA 0.6 nozzle 0.2 layer 3 perimetes 30% grid infill concentric bottom and top infill print orienting hose thread opening to the bed Assembly O ring 38mm ID, 3.5mm diameter Silicon grease Lube both O ring grooves on the…
When you need to save space behind the P3 and the wall, remove original hose adapter from xTool hose and insert this plug inside the hose. 50-60% smaller allowing you to bend the tube closer to the back side of machine. Print instructions…
To wszystkie aktualnie dostępne wyniki.
