20 modeli
A simple 9mm chamber flag for chamber flagging purposes. Print bullet tip up with high or 100% infill at least up to the arm since it needs as much plastic as possible so it doesn't compress or get crushed. These were made to be able to…
A few 5.56 NATO rounds I modeled up to use as snap caps or dummy rounds. All three variants are able to feed and extract in my rifle. The Spec variants are exact to NATO spec dimensions and the ThickRim has a roughly 0.3mm thicker rim for…
This is a simple little device to help load your Ruger Mark IV magazines. It should also work with Mark III magazines since they are cross-compatible. I am unsure if they work for Mark I and II magazines. To use, simply slot over the top…
I wanted a hollow point snap cap because why not and they use less filament than a full round. I use it at the range for training but they can also be used as props or whatever else yall like. Note: Somebody has pointed out that the rim…
Tried to refine things a little bit and implement suggestions I saw in comments. I recommend printing in thin layers, I did 0.12mm. The tongue for the dongle holder needs supports (see picture). Fitment for the dongle is perfect on my…
This is a 3d printed door jim modeled after the Sparrows Mini Jim because I'm cheap and didn't want to pay $10 + Shipping. Use it to open doors. It's currently 1.5mm thick and I kind of want it thinner but it's already a bit flimsy so I'm…
WARNING: THIS IS NOT A STANDARD RMR COVER PLATE! It has been specifically designed to fit an Agency Arms Glock RMR Iron Forward RDS Mount from their AOS line. Pictured is a Gen4 Glock 19. Some context: RMR covers on Thingiverse didn't fit…
This is a modified version of Austin Lively's p365 tlr7sub mounts to tight up the mounting and better suit my personal preferences. I settled on this length after trying out a few variances because it's the largest shelf that can be added…
A simple case and mounting bracket to use BTT's HDMI7 v1.2 on a Sovol SV08. It mounts on using lugs like the original screen. Will probably block enclosure doors if you have them, I don't have the enclosure kit. I think it'd need a…
It's not perfect but it works. Glock mags kind of work but are smoother with Subtle3D's original Glock inserts. Vice versa with sig mags and my insert. When printing, rotate ~15degrees or until the side closer to the flanges is on the…
What the title says. The T-Shank interface is a bit tight and the comb got stuck when I put it in. Needs some dimensional improvements I've been too lazy to do yet. Category: Hand Tools
I saw a double feed practice round while looking for a snap cap model and really liked the concept but the execution just wasn't there so I made my own. These will fit in-between standard rounds or other snap caps but not consecutively. I…
Basically just changed the shape of where your thumb goes to a more standard angled design. Both shorter and longer versions are available.
Minor alterations
I bought a used Lumix 45-150 (H-FS45150) camera lens that did not come with a hood and being a 3d printing hobbyist I figured I'd go find an STL rather than paying for one. The only one I could find was a square lens hood by ChrisNupp.…
Just a very basic insert to help store/organize ar-15 magazines in .50cal ammo cans. This was made because I didn't want to pay the $45 for a premade solution or $30 for a foam insert. I only have Harbor Freight .50cal cans so I cannot…
This is a spacer for the NEXTORCH V51 flashlight holster. It may also fit in the V5 but I do not own a V5 to confirm. The spacer is designed to fit an Olight Warrior 3s so that the light no longer falls through the bottom of the holster.…
I made the Bullet Caddy 5.56 (BC556) because I was annoyed at how 5.56 often comes in 20rd boxes despite AR mags being 30rds. It's also an easy way to segment bulk ammo into single mag amounts. This is NOT meant to be one of those nice,…
Remix to place two 4010 fans on top held in with the cover's corner screws. The old fan port is now an exhaust. This is meant to be used with: https://www.thingiverse.com/thing:4470558 and I haze zero clue if it works with anything else.…
I made this to stick onto my 12rd P365 mags so that they'd sit flush in an Icarus ACE Evo grip module because this dang thing was expensive enough and no way way I going spend additional hundreds outfitting my mags with their special…
To wszystkie aktualnie dostępne wyniki.
