Liczymy pasujące modele…
This is bracket for NVR board NBD7808R-PL. Thank to this bracket, NVR board can be easily installed to Mini-ITX case. Print instructions Rafts: No Supports: Yes Resolution: 0.3mm Infill: 40%
Wydruk około 1,52 €–1,86 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Easily add window screens to your louvered air vents to keep bugs out of your garden shed. Use PETG filament for outdoor use. No supports or brims. Print 2 frames. Apply outdoor rated 1" wide double stick tape to back side of frame. After…
Wydruk około 4,63 €–5,66 € nettoWstępna wycena dla PETGMateriał u źródła: PET
The skid plate on my Bauknecht GSXK 5020 SD dishwasher broke, so I designed a compatible replacement. Apparently these skid plates fit also refrigerators, freezers and other appliances from many companies. Print in STL orientation at 0.2…
Wydruk około 0,30 €–0,37 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This model is compatible with the lego system.
This model is compatible with the lego system.
Zero Clearance insert for DeWalt DWS 780 miter saw. I printed it in PLA+ with 80%+ infill. If you have smaller printer like me (Bambu X1C), insert can be cut in half with Plug connectors (4mm in diameter, 8mm deep). I recommend use 0.20…
The official Cisco part for wall-mounting 7800-series IP phones has been getting increasingly scarce and expensive as of late, so I set out to make a 3D-printed alternative for use at work. Additional Materials Needed: - 2x M3x6 machine…
This is a small protective cover designed for the Knipex side cutter 78 03 125 (without lead catcher). When applied, the cover locks the pliers in the closed position, ensuring safety and convenience during storage or transport. Printing…
Special design to replace the clip for the 780G easy placing on the side of a trouser border. Best material to use is CPE of PC
This is a replacement for the cheap battery cover of the Logitech K780 keyboard. It's quick and dirty and far from perfect, but it does the job :)
This model is compatible with the lego system.
If you ever need to open your tilt-telescopic steering column, such as to install a new turn signal switch, you will find that this part has broken into half a dozen pieces. You can still find them on eBay and Amazon , but if you're like…
Tight lokk til Synnøve fløtemysost, slik at den ikke tørker ut.
This is a mounting bracket which fits the yaesu 8800, 8900, 7800, 7900, and probably others. When printed with ABS this is surprisingly strong (3mm walls probably help), but you will likely need longer screws than the ones you might (or…
este es mi modelo de colector de polvo basado en Fisher shop el de el es de Bosch el mío es de Dewalt en el frente se ajusta perfecto después de 8 pruebas con corte de laser y no necesita hardware adicional para anclarse de usan las…
DC-DC LTC3780 module DIN rail mount Mount of excellent DC-DC sepic converter Compatibility: DC-DC LTC3780 35mm DIN rail Mounting components: M3 screws M3 stand Thanks to Joël P for making a LTC3780 model. If there are any licensing…
Hood seal / Windscreen support. The insert needs to be adjusted with a knife!
Soporte para la FT7800 para atornillar a la pared/Support for FT7800 to screw to the wall Print instructions Category: Electronics Summary Soporte para la FT7800 para atornillar a la pared/Support for FT7800 to screw to the wall Print…
This model is compatible with the lego system.
* NOT COMPLETED YET * Category: Vehicles
Custom Gridfinity base perfectly fits DeWalt TSTAK Deep Box (DWST17806). Prints in 7 smaller parts to fit smaller printers. Base accepts magnets for extra stability if desired. Stash taller parts in irregular spaces between gridfinity…
Print in TPU or similar for flexibility and fuel resistance, also recommend using some gasket maker/RTV to be safe.
40mm Fan mount for Adaptex ASR-7805. Card is recommended in NAS Killer 6.0 build guide from serverbuilds.com. The HBA needs a cooling fan and this will mount a 40mm fan to the heatsink.
You lost your HP workstation mounting screws? Just print 4 of these :D It's not perfect, but it works :)
I made a remix of the Skadis Knipex Snipper for 2 to just hold 1 7803125 snipper.
it takes about 42 hours to print on my ender5 plus at 10% infill you will need to cut it in parts for smaller printers
Simple reference model I took from the website Everything is based off of the a picture and scaled to the size of the USB port From Minisforum Website It's not good enough for a clearance fit But it will get you in the ballpark
Gridfinity Magnet Baseplate for DeWALT T-Stack with 2-Shallow Drawers (DWST17804). Designed to fit in the guardrail slots of dividers. It was created with Gridfinity Workbench, which is a FreeCAD addon. Then, I added holes to fit the…
because I didn't find an appropriate enclosure for my PSU project, I decided to make my own. fits really nice but printing takes a while. had some issue during print with ABS warping, but finallay fixed it some ABS glue - hence the…
Protect your console cart port from dust ect. Use supports, obviously. I do 3 walls minimum on all prints. 15% Infill.
This simple print will let you mount your UM780 XTX to a wall etc. It is open where needed for ports and vents I've printed mine in PETG, 0,2mm Quality preset. 4mm holes, 69mm apart Unlike my previous model for UM690, I've made this model…
The plate is 1 mm thick, which is a bit more than the sheet that comes with the computer, but it fits nicely. I printed mine at 0.2 mm and used some black PLA Unlike the original i haven't added any adhesive to hold the plate as its hold…
This is a LTC3780 DC-DC Converter PCB SELF-ADHESIVE MOUNT. KaosuNeko , thank you very much for the orignal design!
Print 2x 99780 in grey as per the original models parts list. Double check the scale relative to the original pieces to ensure fit.
Recently a friend of mine linked me the original model that i remixed this from as i did not have a bench power supply, and do not really have the cash for buying a proper one, so i decided to do this as my first “big” electronics/3d…
I was getting frustrated that I couldn't find a backplate for my 5 year old video card, so I said to hell with it and made my own. I made this for my EVGA 780 Ti video card, but this ought to work with the 780, 980/980 Ti, and Titan…
This cup holder panel mat was designed based on Ford part number 1L2Z-78046B76-AAA and should be compatible with the following vehicle models: Ford Edge: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 Lincoln MKX: 2007, 2008, 2009, 2010…
Modified some files to fit the XFX Speedster MERC 319 Radeon™ RX 7800 XT BLACK Edition
HP 800 G1, 8000, 8100, 8200, 8300, Ultra Slim USDT Hard Drive Caddy Tool-less Category: Parts
Spare parts forl Lexion780TT. My printed setting: Material: ASA Layer Height: 0.2 Infill: 40% Wall count: 4 Solid top/bottom layers: 5 Need support for print. Postproces - glue two pins to bottom.
To assemble you will need to print our nut hammer and 4, 10x32 nuts and ½" screws If you don't have a 3D Printer I can make it for you from my stores on eBay and etsy etsy - http://www.16bitgamestore.etsy.com/ eBay -…
Created from this data sheet ( https://www.sparkfun.com/datasheets/Components/LM7805.pdf ) to be used when modeling a circuit board if needed. Category: Electronics
Standing feet replacment for G.SKILL Ripjaws KM780
Files to Print Required Print the appropriate files named "[region]_Display_Bottom" for the cartridges you want to display. Then for each additional cart, you can print the files named "[region]_Extension_Cartpiece", and simply screw them…
I couldn't find a reasonable adapter online, so I made this one. It should be printed in place without supports using PETG in the photos. I used 30% hexagonal infill, but less might do. You may be able to increase the miter-side clamping…
Falls eure Lenkstange auch bricht, baut diese ein. Passt ohne Modifikationen
Cap for Yaesu FT-7800 dial knob (Should fit for 6mm, with 4.5mm cut knobs, i.e channel knob in FT-897).
🕹 Stackable Atari 2600/7800 Game Storage – Support-Free Print with Dust Covers Preserve your Atari legacy with this custom-designed, stackable storage solution for 2600 and 7800 cartridges. Each unit is built to hold individual games…
This print combines the Logitech K780 keyboard with a tablet to create a laptop computer by locking the keyboard and tablet together. By locking them together you can use the tablet much more comfortably on your lap. The back braces are…
I purchased a new Atari 2600+ Pac-Man Edition and several new games, and wanted a holder that not only stored my cartridges but also the instructions. I designed this holder to be printed on a Prusa Mini+ without supports. It is quite a…
I couldn’t find an STL to connect my DeWalt DWS780 miter saw to my DeWalt DXV09P shop vac, so I made one. This adapter is designed to improve dust collection and provide a snug fit between the saw and vacuum hose. It was one of my first…
Mobile phone holder for Logitech keyboard K780 or K480. With MagSafe to charge one of the two mobile phones.
lego 36840 36841 99781 99780 2436 99206 87609 64570
This is a RCPROPLUS SupraX 7808 (7 mm bullet, S7) Connector Protection Cap. It's designed to be printed out of TPU, and should not need supports to print, as the overhangs are all > 40 degrees.
Vac hose adapter for Makita ripping circular saw made from TPU. Printed on 0.2 layer height with some infill. Picked TPU as it s a bit more flexible than PETG and wont let the hose go that easily.
Simple print and slide on model, better feel then factory pin. Textured grip and smoother edges. Great little upgrade for the Dws780 saw.
Print for mounting Noctua NF-A9x14 fans (frame removed) to PowerColor 7800 XT Fighter GPU (potentially other models as well, not tested).
Lego (2780) Technic Pin with Friction
easy to print mount for dell optiplex 780 usff Print with PLA 30% gryroid infill / ABS/PET-G 25% gyroid infill (i printed it with PLA) doesn't require supports Happy Printing :)
Just a little USB battery bank I drew up and 3D printed. The enclosure is designed to fit three 18350 lithium-ion cells (WIRED IN PARALLEL) and an AmpRipper 3000 v1.0 from Kickstart Design (Link below). Assembly is very easy. First, plug…
This was a project for the course advanced prototyping at TU Delft. With the help from Joris from Protospace, we fixed two old ultimakers togheter, adjust firmware, and let them print at the same object in 1 print! Check out the…
This is a custom-designed replacement knob for KitchenAid toasters 5KTT780 part 4176838 . The model is designed for durability and precise fit and has been optimized for 3D printing in polycarbonate (PC) . It is intended as a functional…
I bought a Logitech K780 keyboard and can fit most phones without a case in the slot but as soon as I put a case on my Pixel 10 pro it no longer fits. made this little adapter for a wider slot to fit my phone. It also has carve out for…
Although there are many LCD controllers for the RepRap, there are fewer with a memory card that can easily be removed. Most of the SD adaptors are difficult to mount into a box and the micro SD format is uncomfortably small. Although the…
This is a Mounting Kit for a 4 Pole Female 3.5mm headphone jack, to solder into a Composite Video Mod, intended to replace the Atari 7800's RF modulator. The idea is, instead of drilling holes into your 7800, you would replace the RF…
Simple case for a rather popular LTC3780-based board from Aliexpress e.g. this one: https://aliexpress.com/item/1005009222609081.html It features a place for a 4cm fan in the lid, though you might need a separate power source to feed it,…
Print upside up 75% Infill Supports - YES
Stifthalter für edding 780 Lackstift , oder andere Stifte mit unter 12mm Durchmesser ------------------------------------------------------------------------------------------------------ Pen holder for edding 780 , or other pens with a…
Dishwasher Dishrack Roller WP99002780 Suitable for when the bracket is still ok, but the wheel has broken. Snug inner fit, consider filing inside slightly depending on your printer settings.
BenQ EW2780 Monitor Riser - 45mm lift
Work in progress. Power button needs work and I need to add a backplate
A vertical desk stand for Logitech K380 and K780 keyboards. These little legs don't take much room when unused, but it can free up a lot of desk space by placing the keyboard vertical. This is a remix of smogan71's “K380 wall mount for…
Features - Full wrap — covers back, sides, top and bottom - Large front window — full access to the screen and the navigation buttons - Rear keyhole slot — works with the original slide-on belt clip - Top opening (Ø24 mm) — clears the…
I move the monitor a lot and lost the original base
This life-size, non-functional replica of the MiniMed 780G insulin pump is designed to help you make custom pouches, holders and other accessories. Most of the model was captured using a high-resolution 3D scan. The transparent reservoir…
A stand for the Ayaneo Next that slots into the phone/tablet stand on the Logitech K780, so you can play games that require a mouse and keyboard on the go. Works fine, just be careful when you pick the device up out of it, I somehow…
This a fan shroud to replace the standard 95x10mm fans with 120x25mm ones, I used Arctic Cooling P12 PRO ones because it have a very good cost/performance ratio. The main idea it's to use their high static presure to blow aire using a fan…
A simple custom fan shroud for XFX Merc Series graphics cards of the RX7000 series. Low profile, accepts any 120mm fan using M3 hardware. Uses M3 threaded inserts (d=~4,2mm, L<7mm). Includes optional flexible exhaust duct (soft TPU).…
Compaq Armada 7800 CF/HDD Adapter --------------------------------------------------- Adapter to fit an old hard disk to Compact Flash card. This fit the Compaq Armada models: 7700 7800
Panel version is not really made to be printed seperately but incorporated into a panel/lid
Print with or without supports. Either way requires cleanup. First try was slightly long, but still fits, and is easier to reattach the strap to. Use “Short” version for tighter fit, untested. Took me 5 minutes to put together.
When converting a vehicle from Manual to Automatic or to Electric, the clutch master cylinder is not used anymore, leaving a hole in the firewall. Automatic cars came with a cover washer in place of the master cylinder, but it appears to…
Worked this up to repair a coworker's vacuum. This may work on other models of Shark vacuums, but I do not have them for testing. I printed this in both PLA and PETG and both work fine. I used 5 walls and 25% infill for added strength.
This tiny cart display stand is the smallest you will find. I made sure there is just enough gap between the back rest and the lip for most cartridges. The non-card type cartridges look like they are floating due to the tiny size. The…
Playmobil7106780 2 - 6551575
Simple rain protection for your NVR780 To shape it perfectry to your wall use hair dryer or air heat gun to softern plastic. Attached to the cover via dual sided tape.
Haben diesen Ständer/Halter gemacht um mehr Platz auf der Arbeitsfläche zu haben. Denn stehend braucht der Dremel 780 wesentlich weniger Platz. Man muss lediglich den Aufhängbügel entfernen. Bei mir egal da ich ihn sowieso nicht hängend…
I printed from PETG with a layer of 0.12 mm, infill 80%.
Desktop stand for a PV780, or PV780B, or HV780 display. Includes holes for 8-32 mounting screws, or bezel mount. Recommended print settings: Layer Height: 0.2 mm or less Infill % : 15% Supports: No Print Orientation: Default as modeled…
As long as you don't intend on hanging by these, they work to at least index and secure the Riverbed unit in place. In case you're not like me and have other bolts than 20mm M4-0.7 screws for your Riverbed, I've included the f3d file to…
Plastic part that turns part of the door.
Makes www.thingiverse.com/thing:3127804 compatible with Pop! devices. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 38 Filament: NovaMaker PLA Category: Mobile Phone
This Niko switch 101-78010 lights our bathroom automatically. Nice except during the night when you do not want any light ! This simple cash solve my concern. PLA is a good choice.
Housing for the NAU7802 Food Scale project. Category: Electronics
playmobil7116780 1 - 6551580
This adapter lets you convert the Bestway Saluspa Hot tubs using the P07805 filter housing to the more common and available P05343 housing with screw threads. I ran into this issue with my saluspa hermosa inflatable hot tub that uses the…
Konnte keinen passenden Adapter für meinen Staubsauger finden also habe ich diesen hier entworfen. Adaptiert von 34mm am Staubsauger auf 27,3mm an der Handkreissäge. Gedruckt in TPU 95A mit 20% Füllung.
This is just a simple phone Mount for my office phone. I know it works for the Cortelco 8780, but probably works for many others with the same distance on the keyholes.
Since shelf space is limited for me, I wanted a way to get some games off my shelf and display them. I had seen/tried other similar items out there, but they all seemed to be too big/bulky and use too much filament, so I decided to create…
