562 modeli
This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install. UPDATE 27/01/2021 Added the 3…
Wydruk około 0,22 €–0,27 € nettoWstępna wycena jednego wariantu
Cap/Cover for female Ethernet Ports to prevent dust from getting inside. Easy to print without any supports. You can use a brim if you have adhesion problems. Both, PLA and PETG, are fine. But I would suggest to use PLA, because PETG has…
Wydruk około 0,53 €–0,65 € nettoWstępna wycena jednego wariantu
Ethernet cable fix which prints WITHOUT SUPPORTS. The layer line orientation aids in keeping the cable in the port. Print settings: layer height 0.2mm 3 thick walls Infill: Does not matter since the piece is too small to even have infill…
Wydruk około 0,11 €–0,14 € nettoWstępna wycena jednego wariantu
Cable organising clips for ethernet cables
Wydruk około 0,20 €–0,25 € nettoWstępna wycena jednego wariantu
update: This model has updated to v2 having now stress relief for power and ethernet cable. --- Stress relief for Prusa Mini power and ethernet cable. I felt like the power plug moved too much and possibly caused stress for the power…
Wydruk około 1,93 €–2,36 € nettoWstępna wycena jednego wariantu
An ethernet RJ45 repair clip with a working snap lock that locks the plug in the socket. Prints without supports added from the slicer thus it prints quicker and and uses less material. NOTE: Needs to be printed with 3 perimeters (3…
Wydruk około 0,11 €–0,13 € nettoWstępna wycena jednego wariantu
An anti-tamper lock for RJ45 Ethernet Cable connectors. I have cleaned up the original, made the hole smaller and cut off two of the corners to make it fit in more scenarios
Wydruk około 0,16 €–0,19 € nettoWstępna wycena jednego wariantu
Quick fix for RJ45 plugs whose little clip broke off. Because there are so many variations of RJ45 plugs and every one needs a different version of this model, I uploaded a .STEP file and an editable Fusion 360 file where all the…
Wydruk około 0,10 €–0,13 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This wall mount is designed for the Starlink Ethernet Adapter. There is room for the cables to connect into both sides. Optimal design for 3D printing, made to be strong, durable, and reliable. The Starlink Ethernet Adapter fits tightly…
Wydruk około 2,84 €–3,47 € nettoWstępna wycena jednego wariantu
Remixed the ethernet port cover to print in an orientation that makes it far less likely to break off within the port. This orientation also increases the part surface on the build plate - reducing the need for brims. Finally, I changed…
Wydruk około 0,14 €–0,17 € nettoWstępna wycena jednego wariantu
After lots of versions, I think I have made a nice cable dresser. Designed for Cat 5, may need to be slightly scaled up for Cat 6 and beyond. Directions (if you really need them) Print two at a high infill for strength. Put them together…
Wydruk około 4,29 €–5,25 € nettoWstępna wycena jednego wariantu
I sleep in complete darkness and usually tape all things that light up in my room. The Ethernet cable port is harder cover up so made a cover for the lights instead. Photo of Device has duck tape residue.
Wydruk około 0,11 €–0,14 € nettoWstępna wycena jednego wariantu
Great way to easily store your long ethernet cables! *Spool pictured is holding 115 feet of CAT6 ethernet cable. Hardware needed 8x M4x8-10 8x M4 Heatset Insert 4-5mm in length Printing PET-G .2 mm default settings Infill: 15-20 gyroid…
Wydruk około 7,89 €–9,65 € nettoWstępna wycena dla PETGMateriał u źródła: PET
As PrusaLink/PrusaConnect now supports USB Webcams, I've remixed Prusa's Raspberry Pi Zero frame for Einsy Rambo model to provide some protection for Waveshare's Ethernet/USB Hub pHat. The Waveshare pHat comes with brass spacers and some…
Wydruk około 0,66 €–0,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Netzwerkkabel lassen sich Platzsparend aufwickeln und aufbewahren. Verlegte Kabel sind oft zu lang und sind schwer irgendwo zu “verstecken”. Mit dieser Kabelrolle lässt sich die überschüssige Kabellänge bequem auf wickeln, mit den…
Wydruk około 0,08 €–0,09 € nettoWstępna wycena dla PETGMateriał u źródła: PET
This is my NETGEAR GS305 Ethernet switch enclosure for my printer 3D desk. I use 4 screws 3x8mm for fixing the top You can now fix your ethernet switch on a desk or on a wall or under a shelf.
Wydruk około 1,51 €–1,84 € nettoWstępna wycena jednego wariantu
pdated version of the RPi Zero Frame to protect the Waveshare Ethernet/USB Hub pHat for Webcam usage with PrusaLink.
Wydruk około 0,64 €–0,79 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Mir hat die Farbe nicht gefallen, deshalb habe ich ein eigenes Gehäuse designt. Einfach das alte Gehäuse abklipsen, neues dranstecken und zusammenkleben. Hier habe ich die Fensterdurchführung bezogen:…
Wydruk około 0,38 €–0,46 € nettoWstępna wycena jednego wariantu
I remixed this to fit a GMRS extension RJ45 (CAT5) cable that's routed from the arm rest through the panel...I resized this to fit the smaller port in the bottom, and added two cutouts: pass through for CAT5 Cable for install larger hole…
Wydruk około 0,29 €–0,35 € nettoWstępna wycena dla PETGMateriał u źródła: PET
Ethernet (RJ45) Port Dust Cover cap with grip for easy removal. Just added: New slimmer/narrow model for switches with closely spaced ports. Check out all other port covers: USB-A port cover -…
These are replacement clips to fix broken ethernet cable clips. The clips attach to the Ethernet cable and replace the broken clip so that the cable stays locked into an Ethernet port. EDIT - For some reason Simplify3d doesn't like this…
This design is a unique combination of the short designs, where the latch is fixed at the connector and the longer designs, where the clip is mounted to the cable behind the collet. The design considers the exact dimensions of the collet…
This is my attempt for a universal cable labeling system. The label holder consists of a main part and a snapable cover. Labels can be stuck to the main part's flat surface or inserted into the cover if they are not sticky. Thus, using…
This is a repair clip for your broken Ethernetcable. You can easy print it. The clip makes it possible that the cable does not always slip out so easily when the clip is broken off at the top. To print: you can use PLA too Use supports
3d printable ethernet cable label, print in one piece without support, compliant hinge system. I posted 3 sizes but add a comment if you wish another one, or use the fusion file I posted 3D PRINTING SETTINGS 0.12mm
This was first inspired by @ ktothestank who made a simple wire straightener. I printed and tried it since I'm doing a lot of ethernet terminations, and decided to start from scratch and iterate 5 times on something that would have more…
for easy storing my network cable during traveling. It is for 20m cable length. i modified it for 10m as well see on Prusaprinters. https://www.prusaprinters.org/prints/47891-cable-spool-ethernet-cable-10m
💻Ethernet Cable Runners💻 Nozzle 0.4mm Print 0.2mm Infill 50% Support ❌ Brim ❌ Here are all our plans, take a look. Qui ci sono tutti i nostri progetti, dacci un occhiata. 📃→ ALL COLLECTIONS info: 👤Account link to share it= idea-prints…
Update: Added x2 and x1 clips Simple wall clip for UTP/ethernet cables reuploaded from Thingiverse , original design by Agustin_Pulido
Summary Slim RJ45 Ethernet Cap / Coupler that will save your ethernet cables and especially the plastic retaining tabs on your ethernet cables in bags cluttered with other cables. There is one open ended file to customize to your…
This is a cable comb for Cat 5e Ethernet Cables. Looking for a Cat 6 variant of this model? <Click Here> ← To be updated
Cable manage ethernet runs with some spacers I made. If you want more sizes just ask and I can upload them 👍 Currently Supported Sizes 5x2 5x2 -1 4x2 3x2 2x2 1x2 5x1 4x1 3x1 2x1
I needed access to a few more USB ports on my Voron 2.4. I already had the USB keystones on hand from Amazon https://www.amazon.com/gp/product/B07Z94HYFG?th=1 There is very little space inthe honeycomb to mount anything, so I designed…
This is an ethernet dummy plug to reserve or protect a network port. It is designed to be printed on its side for strength of the clip. I included a plain version and one with a clip protector. I also included a version with and without a…
Add a second ethernet port to your mini PC! This adapter plate allows an ethernet port to be mounted in the Flex IO slot usually used for an additional display connector. This was designed for a ProDesk/EliteDesk G4, but it may fit other…
Ethernet cable clips and cover for routing along walls. Uses standard course drywall, #5 or similar screws. Versions for one through four cables are included. The cover was intended for routing the cables through a wall near a corner. One…
10" Rack Mount Bracket Ethernet Switch TpLink 8 port Flat version – Use this if you don’t have space issues between rack units (you can print this model horizontally); Standard version – Provides extra inter-unit clearance. Choose this if…
just print and screw the pieces together to help straighten the ethernet cables and makes it easier on your hands Can be used with a heat insert or tap out the 0.2mm 1st layer and a just use an 3m nut Hardware: M3x3.6 or 4mm heat insert…
This is a remix of Ethernet Port Dust Cap/Cover - No Supports from kerngebiet with a larger base for easier printing and easier extraction of the cover. The initial design was a bit loose in my ethernet ports, therefore I added a 105%…
for easy storing my network cable during traveling. It is for 10m cable length. 20m variant https://www.prusaprinters.org/prints/27496-cable-spool-ethernet-cable
I have another advanced version of this that has various sizes (30, 32, 35, and 40 to ensure your adapter will fit). https://www.printables.com/model/886799-rj45-ethernet-cable-rj45-keystone-mount I could not find something to protect the…
Made a shield to fix the illumination from my wifi accesspoint led light. Tape didn't cover the light enough. Using a printed piece makes it removeable again. Best to print with some more infill and darker color to block the light.
Designed to fit flat ethernet cables. Insert your cable into the center of the spool before snaping it together. coil the cable and push the free end through one of the hexagonal holes to hold the cable in place. Both ends of the cable…
This is a problem that has plagued me for over 20 years. I was so pleased to see several 3D printed solutions. Unfortunately the original design by guss67 typically requires supports. To combat this there are designs that print in the…
I tried to use @kulfurst Nintendo Switch Horizontal Flip Dock , but found that it doesn't fit the Ethernet version of the dock that is included with the OLED Switch. I redesigned the stand to fit the Ethernet dock from scratch, but…
Tips: Set PLA temperature to 220℃, even 230℃. Consider using PETG - it's better suited for flexible joints. Try 0.12 mm layer height Scarf joint is required to prevent flexible tab breakage Print on the side with supports to achieve…
I basically made this for pulling cables behind walls or above ceilings (original ethernet plug was from Dead End - Ethernet protector by SarahAlroe). You can stick a wire or piece of string through the loop and pull it through, hopefully…
These Models are for Ethernet Outlet Plates or Covers for one, two or four Keystone Ethernet Couplers or Jacks. I've included models for both a standard sized Outlet Plate and an enlarged or XL Outlet Plate. I recommend printing with 4 or…
A print in place version of the Ethernet cable straightener. A second hole has been added to straight the wire pair, if desired. Printed in overture PLA Professional (PLA+) for best strength @0,20
This is an updated version of my last cable comb . After some critiques from @ heyitsdubblea I went back to this and added screw holes so that you can screw this into a wall. I also knocked down the edges a bit with it. I also have…
This is a flat pack case for the Raspberry Pi Zero sporting the waveshare POE ethernet and USB hat. HAT in question : Waveshare POE ethernet Benefit of the case: Flat pack design Maximum airflow Has space to have a Pi Zero with headers…
Wanted something like the original design but something to protect Ethernet endcaps. Also made the gap to hold the cable inside the clip better.
just a simple single port wall plate for ethernet with a RJ 45 keystone
This cover created to protect Ethernet connector from dirt and humidity when using in field. Created for Ukrainian Army.
This is a bracket for the hp elitedesk 800 g6 (DM/1L PC model) flex port 2. Usually a discrete GPU or serial add-on use this cutout in the chassis but I wanted a bracket for an ethernet to m.2 (A+E Key) card since my WiFi slot wasn't…
Hello! Forgot to add the boot/cap/cover to your RJ-45 cable and you crimped it already? been there, done that. Hope this helps. This is a work in progress (W.I.P.) as it's not the easiest print using FDM printers, yet. Update 2022-09-07…
A case for the ESP Thread Border Router with attached Ethernet daugther board. The Border Router is developed by Espressif and consits of an ESP32-S3 and ESP32-H2 SoC. It can serve as a Thread Border Router using the Openthread Border…
This is a Remix of HP ProDesk / EliteDesk G4 Ethernet Port Flex IO Adapter von Burf | Kostenloses STL-Modell herunterladen | Printables.com from Burf. Please see his Model for Details. I could mount my Bracket without modification of the…
A minimal, protective half-case for the STM32 Nucleo-144 development boards, with heat set inserts and screws.
An ethernet RJ45 repair clip with a snap lock that locks the plug in the socket. This model is optimized for sideways print so that the snap lock prints with the layer lines to increase the strength. Use: 3 perimeters (walls) supports To…
Dust shield or block-off for female ethernet ports, includes a pull tab for easy removal. Remixed from a model which had no pull tab to make removal more difficult for unwanted users, I added the pull tab to make it easy to remove. I…
Print them in the supplied orientation. Using a 0.6 mm nozzle, you can get away with a single perimeter and no infill. They are meant to be attached with tesa powerstrips, command strips, or anything similar. If you want to print…
This is a bracket to mount a network media converter to the rail in a network cabinet/rack. As it is just fixed on one side, it fits 19" and 10" racks equally well. There are two holes for the cable inlet on the back to allow the…
Einen ähnlichen Clip gibt es hier schon, der bei mir aber immer wieder gebrochen ist, egal, ob ich PLA oder PETG verwendet habe. Deshalb habe ich einen ähnlichen kreiert, der allerdings aus 2 Teilen besteht, sodass ich die Druckrichtung…
Rack mount for cheap 2.5GbE switches with 1 SFP+ port. Use one of the models from the original model to fill in the other side. This includes a backstop and block to hold the power cable. These 2 features require support, but no other…
We have switches / PLC's at work that occasionally get relocated. Every now and then, the wrong un-configured ports get used to re-connect these devices. These aren't really to stop people from pulling them out if they wanted to with some…
I was asked to make some tags for charging cables for use by elementary school age kids. After not finding any that looked durable enough, I designed these to withstand heavy every day usage. There are several different sizes, use a…
I was inspired by the many designs for RJ45 repair clips, but they all suffered the same issue - the retainer part was bulky, fragile and never fitted my oddball collection of cables. They also required supports. The cable tie method fits…
Easily identify cables by placing the same number at each end of a cable, you can place multiple on each end if needed for 2 or 3-digit numbers
HP G1, G2, G3, G4, G5 EliteDesk/ProDesk Flex IO v1 Ethernet NIC Bracket
Here's a basic cable clamp for securing a pair of cables to a stud (or whatever you want to screw it in to). The screw hole was intended to fit a drywall screw, but other's should fit fine. I made this for helping-square up ethernet…
this is a cusom version of http://www.thingiverse.com/thing:626368 where i removed alot of the holes and the mounting, but i still have the stl with mouning and some of the holes but not all. it took around 5 hours to print (1 hour for…
This is version 28 of my universal ethernet plug that I designed for work Design features: Friction mount No supports required Made with PLA 0.2mm layer thickness Average print time of 5-10min Carefully located pressure points to avoid…
A NAS and a switch tend to illuminate my bedroom due to unfortunate (but unchangeable) placement. I made a very slim RJ45 LED plug cover, which slides on easily and does not come off on its own when unplugging cables. Works also with…
The Dell Wyse 5070 is a thin client with two DDR4 SODIMM slots one M.2 PCIe slot, and one M.2 SATA slot. Typically the PCIe M.2 slot has a wireless card installed, but I wanted a second Ethernet port so I could run opnSense on the machine…
I designed this tool, to assist in fabricating ethernet cables. It maintains wire formation, in preparation for insertion into the RJ45 Jack. It also assists in precisely cutting wires to (13mm) the correct length.. Strip off about an…
Das Modell ist auch 2-teilig, aber ohne Kleber einfach zusammensteckbar
Best fit is to print it on 0.2mm (standard settings for either Prusa, Bambu, Voron or other printer). 3mf file is including text for printint in multiple color.
Remake for longer ethernet cables +20m (flat or round) Diameter stays the same, i made it wider. Together with the clip.
A cable clip for attaching flat ethernet cables to walls/skirting boards. I wanted some something to attach a new cable snaking through the house, to the wall. i didn't want to use nails so i designed this to use 10x10mm double sided…
Required a frame to mount the 8-port Ethernet switch under a stand. There are other similar models around but I experience occasional bouts of not-invented-here syndrome. There is g-code attached is you happen to be using PETG. This will…
I print with 25% infill with PLA.
Designed to guide 24 ethernet Cat 6 cables to a 24 ports patch panel. The holes are numbered to match the port number (for future actions). Also, you can found a version Switch numbered (1-3-5 ...) Around the piece you have a guide to…
Print in TPU. Remove the latch from connector. If you also implement PoE mod for the Starlink Mini, you may need а plug for power port, see my other model.
RJ45 Ethernet Network Switch LED Light Shield Cover Print with any material
This works with HP EliteDesk and ProDesk G6 (and possibly G9?) Mini systems. It replaces the blank panel on the Flex IO 2 Port and let's you mount an ethernet adapter. It might work with other Ethernet adapters, but I've only tested it…
Just a little mount to hold the starlink ethernet adapter. It's a snug fit and the cable holds it too. Easily printed with the largest surface on the bed and I've mainly made them out of PLA on my Prusa mini in draft mode
This bracket holds a Netgear GS308 Ethernet switch to the underside of a shelf. Uses four wood screws to attach. Print instructions I used PETG. PLA would probably work too. Print settings are not critical -- it didn't need support or…
Printed with PETG filament with 0.25 nozzle, 10% infill (it's more flexible). Look at the photo of how it is best to place the pieces on the bed. I have included the entire alphabet, numbers, and one piece without markings. I have also…
Print using Supports (Everywhere) then pick open the gaps for the ports. Designed For: PI Zero 2W ETH USB Hub Hat (b) SKU: 20416 Part Number: ETH/USB HUB HAT (B) Brand: Waveshare Dedicated Aluminum Heatsink for Raspberry Pi Zero Series,…
Installs into the secondary display port, just above the built-in network and USB ports. Requires: 4x M3x4x5 heat-set inserts 2x M3x8mm countersunk screws Also uses 2 screws removed from the original metal bracket Potentially worth…
This is meant to be printed in a flexible filament and must be put on before crimping the cable. Tested with CAT5 cable. The project page with more information is here:…
Guide for 4 Ethernet cables mounted to the wall.
Simple ethernet/CAT5 cable clip. Wanted a clip that I could mount and then come back and run my cable. It's frustrating when holding a cable, a clip, and a screwdriver.
A simple wire management solution for securing network cables. It hold 14 ethernet cables and has multiple holes for mounting inside a server rack or under the desk.
My ethernet cable couldn't reach my computer without dragging on the floor, so I designed this to neatly route it along the door frame instead.
I’ve upgraded my Flsun SpeederPad with an RJ45 connector for ethernet access. Works perfectly, just need to solder a PCB connector. Ive designed a new case to allow access to the new RJ45 and also to the 4th USB port, USB OTG and 3.5…
My version of a project box for Arduino Mega that includes an ethernet board and one custom project board on top.
I wanted a cheap 2.5Gb ethernet switch and found one on aliexpress. As with all equipment like that, there's no rack mount included so I had to do my own (rack isn't ready yet, but I'm preparing my devices). Fit is tight, so you even…
Long version that can hold up to 8 ethernet cables (4-7mm), and cables stays inside the slots when the clip is opened
