Wyniki wyszukiwania: lens

Sortowanie

4295 modeli

P
PrintablesElektronaut

M42 Body & Lens cap

The body cap has a slightly undersized M42x1 thread and the rear lens cap has a sightly oversized M42x1 thread. This ensures a loose fit. The prints shown in the pictures were done with a layer height of 0,15mm.

Wydruk około 0,75 €–0,92 € nettoWstępna wycena jednego wariantu

Pobrania
1377
Polubienia
96
Ocena
5
P
Printables3DHirn

55mm One Piece Lens Cap

Idea I needed a new lens cap for my lens and tried to challenge myself to desing a one piece one that has built in springs. This is the result of that. Printing The print is fairly self explanatory, just print it with the logo side down…

Wydruk około 1,07 €–1,31 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
1065
Polubienia
105
Ocena
4,75
P
PrintablesM1Designs

Camera Lens Cap 58mm

Both pieces need supports . It should take less than an hour and a half in total. For the settings keep reading, for the story skip down below. The assemble it make sure all supports are cleared and slide the end without the ridges under…

Wydruk około 0,22 €–0,27 € nettoWstępna wycena jednego wariantu

Pobrania
846
Polubienia
52
Ocena
4,5
P
Printablessteffenbew

iPhone 12 Lens Filter Mount

Mount any 67mm camera lens filter to your iPhone. It's precisely measured to fit an iPhone 12 (Pro), without a case. I'm using it with a ND2-ND400 (9 Stops) Filter from K&F for filming. Advantages over commercial products I found: All…

Wydruk około 0,19 €–0,24 € nettoWstępna wycena jednego wariantu

Pobrania
473
Polubienia
51
Ocena
0
P
Printablesdteng

LED Light Pipe and Lens for Original Prusa MMU3

The LEDs on a stock MMU3 are difficult to see unless looking directly into the holes, especially when viewed from the front with the MMU mounted at the standard angle. These light pipes and lenses disperse the light over a wider angle…

Wydruk około 0,10 €–0,12 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
353
Polubienia
104
Ocena
4,97
P
Printablesoltas

Feder für Sony Objektivdeckel, spring for sony lens cap

Ich habe die Ferdern für 55 und 72mm Objektivdeckel entworfen. der Remix von Martin stellt eine Version für 49mm Objektivdeckel bereit I designed the springs for 55 and 72mm lens caps. Martin's remix provides a version for 49mm lens caps.

Wydruk około 0,35 €–0,43 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
339
Polubienia
71
Ocena
5

Lens Cap 49mmØ

Hey there :) Step 1: Load the files into the slicer Or you use the prepared gcode, just look at the requirements Step 2: Correct the orientation of the models: The FRAME is printed with the Logo facing down and the bridging should be from…

Wydruk około 0,95 €–1,16 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
332
Polubienia
43
Ocena
4,2
P
Printableskevsparky

Canon Lens Back Cover

A rear lens cover for Canon Lenses. If printing on an FDM printer, the Canon logo should be on top. You may want some support material to support the rear side of the internal flat surface. 0.15 mm layer height is ideal. No support…

Wydruk około 1,59 €–1,95 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
315
Polubienia
57
Ocena
5
P
PrintablesBitScout

Lens cover for AUKEY webcam

New: v2, which is a lot more solid, doesn't catch on the lens bulge and only slides off sideways. Three versions of a simple webcam cover for the 1080p AUKEY webcam (the wide one, with microphones on each side). The cover slides easily…

Wydruk około 0,13 €–0,16 € nettoWstępna wycena jednego wariantu

Pobrania
229
Polubienia
16
Ocena
5
P
PrintablesPenguinNinja

Bokeh lens filter (fits over a 58mm lens)

This is an attachment for a bokeh filter. It fits over a 58mm lens. I designed the base free to rotate, so that I can make bokeh images in the background rotate also. Each filter slides into the top of the base. I have 17 pre-made filter…

Wydruk około 0,67 €–0,82 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
219
Polubienia
47
Ocena
5

Lamellenstopfen 40mm x 40mm

Lamellenstopfen als Abdeckung für ein 40mm x 40mm in 3mm Stärke Formrohr. Ich habe dies in PLA gedruckt und funktioniert einwandfrei. Standard Slicereinstellungen 0,2 mm und 15% infill.

Wydruk około 0,71 €–0,86 € nettoWstępna wycena jednego wariantu

Pobrania
197
Polubienia
5
Ocena
4
P
PrintablesFelixAtter

lens cover for uconsole

clip on lens cover for uconsole by clockworkpi Prints with no supports with flat against build plate

Wydruk około 1,37 €–1,67 € nettoWstępna wycena jednego wariantu

Pobrania
188
Polubienia
14
Ocena
0
P
PrintablesBM

Extra-wide lens hood Canon EW-73D alternative

The hood is not visible on the photos. The fuzzy skin gives a nice touch to the look. Printed in ABS-T to withstand the sun. Amternative to Canon EW-73D compatibel with RF 24-105mm F4-7.1 IS STM. Not tested on EF-S 18–135mm f/3.5–5.6 IS…

Wydruk około 1,84 €–2,25 € nettoWstępna wycena jednego wariantu

Pobrania
170
Polubienia
12
Ocena
0
P
PrintablesStampBoutique

49mm lens cap with flaps

49mm lens cap with flaps for easy screw and unscrew.

Wydruk około 0,27 €–0,33 € nettoWstępna wycena jednego wariantu

Pobrania
166
Polubienia
6
Ocena
5
P
Printableshuberjer

Cover Lens for ArduCam 8MP IMX219 Sensor 175deg Wide Angle M12 Lens Articulating Raspberry Pi Camera Mount for Prusa MK3 and MK2

A Remixed Cover Lens for a Raspberry P1 Camera V2 board with an ArduCam 8MP IMX219 Sensor module (for RPi and Jetson Nano) with a 175deg Wide Angle M12 Lens. I included the Step file for your remix convenience.

Wydruk około 0,28 €–0,34 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
137
Polubienia
6
Ocena
0
P
PrintablesGeoff

Kodak Type M Cine Lens Adapter for MFT Cameras

I didn't know of any available adapters for these unusual lenses, so here one is! The smart little Kodak Cine-Ektar 25mm f/1.9 is the only one I have tried, but the coverage on a Four Thirds sensor is pretty good and it is quite usable. I…

Wydruk około 0,77 €–0,94 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
121
Polubienia
7
Ocena
0
P
Printablesb8trez

Leupold VX-5HD - Flip up style objective / ocular lens cover set - 44 mm objective

Hey team, I've put together an objective and ocular ‘flip up style' lens cover to suit the Leupold VX-5HD. Leupold themselves make absolutely stunning lens covers ( example ), which are beautifully machined out of aluminium and fit their…

Wydruk około 0,38 €–0,47 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
105
Polubienia
14
Ocena
0
P
PrintablesVBalsa

Pixel 9 Pro Moment T-Series Lens Mount (Ringke Onyx Case)

Print at normal speed with a dark color PLA. Light can pass through white PLA and cause lens flare. The file has the correct orientation, print w/ organic supports. Will require some very light sanding. This may fit into other cases that…

Wydruk około 0,12 €–0,15 € nettoWstępna wycena jednego wariantu

Pobrania
105
Polubienia
17
Ocena
5
P
PrintablesBouggo

Brillenständer in Katzen-Design – Glasses Stand in Cat Design

Hiermit drucken Sie einen Brillenständer im Katzendesign aus. Sinn und Zweck ergeben sich aus den Fotos. Die farbigen Bilder stammen von BlocksCAD, mit dem ich das Objekt erstellt habe. Ich habe einen weiteren Ständer entworfen:…

Wydruk około 4,19 €–5,12 € nettoWstępna wycena jednego wariantu

Pobrania
103
Polubienia
6
Ocena
0
P
PrintablesSpotmatic

Version 1: Lens cap for TLR with mounted filter, bayonet 1 (Aires reflex, Rolleicord, Rolleiflex, Yashica, Minolta)

Keep the filter on and place this lens cap on to protect it. Suitable for TLR Bayonet 1, Aires reflex, Rolleicord, Rolleiflex and others. Filament: PETG Which one to print? From left to right: Lenscap for Rolleiflex with bay 1 filter on,…

Wydruk około 0,36 €–0,44 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
95
Polubienia
11
Ocena
0
P
PrintablesThomas Mayr

Fujifilm Lens Stand

Only works with original Lens bottom caps. Shape is slightly conical and was adapted to fit them perfectly. Printed on Prusa Mini+ with PLA

Wydruk około 1,65 €–2,02 € nettoWstępna wycena jednego wariantu

Pobrania
83
Polubienia
18
Ocena
0
P
Printableseof

Reinforcement Glass Stand / Verstärkter Brillenständer

I include the Fusion source, so that one can adjust it to personal needs.

Wydruk około 0,82 €–1,00 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
81
Polubienia
7
Ocena
0
P

Canon-FD lens mount cap

Simple Canon Fd mount cover cap to protect your lens mount. Works with interlocing lens mechanism.

Wydruk około 0,89 €–1,09 € nettoWstępna wycena jednego wariantu

Pobrania
80
Polubienia
8
Ocena
0
P
PrintablesFazal Majid

Lens caps for the Zeiss Victory Pocket 8x25 binoculars

Objective and eyepiece covers for the Zeiss Victory Pocket 8x25 binoculars. Print instructions Use PETG at the 0.10mm Detail setting, rotate 45º so the lines are parallel to the lens axis.

Wydruk około 0,57 €–0,70 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
62
Polubienia
3
Ocena
5
P
PrintablesYao Wei

Sirui/Moment Lens Adapter for iPhone X/XS

Model originated from Thingiverse and fixed model issues. Please note that phone cases may be needed in order to properly hold this adapter. This model is confirmed to be able to fit into Rhinoshield SolidSuit, but may require cutting the…

Wydruk około 0,16 €–0,19 € nettoWstępna wycena jednego wariantu

Pobrania
59
Polubienia
4
Ocena
0
P
PrintablesBrightGecko

M7 sensor lens casing for OV5647 (ZeroCam / Arducam)

Replace the original M6 threads on the OV5647 sensor (Arducam/Zerocam) to M7 threads with this casing. Before changing the threads, you need to remove the original M6 lens casing from the OV5647 sensor body. To do this, you can carefully…

Wydruk około 0,08 €–0,10 € nettoWstępna wycena jednego wariantu

Pobrania
41
Polubienia
1
Ocena
0
P
PrintablesGlenn Brockett

Bahtinov Focus Hood for 69mm lens

A simple “Drop over” Bahtinov mask for camera lenses under 69mm. (Half of my lenses work with it.) Place over your lens and focus on a star until the | splits the X. https://en.wikipedia.org/wiki/Bahtinov_mask Pattern generated using:…

Wydruk około 0,94 €–1,15 € nettoWstępna wycena jednego wariantu

Pobrania
36
Polubienia
4
Ocena
0
P
Printablesknopersikcuo

Sinar lens board 26,3mm

Hi, Sinar lens board (139x139mm) with ~26,3mm hole, the circle which is “deeper” is 20mm deep and have 100mm diameter. Print in PLA laying on the front with supports inside the ring. 27.05.2025 / Added version with 30mm depth ring.

Wydruk około 4,45 €–5,43 € nettoWstępna wycena jednego wariantu

Pobrania
29
Polubienia
4
Ocena
0
P
PrintablesKen Hammond

Bushnell Citation Binocular Lens Cap

Replacement lens cap for Bushnell Citation Binoculars

Wydruk około 0,42 €–0,51 € nettoWstępna wycena jednego wariantu

Pobrania
24
Polubienia
5
Ocena
0
P
PrintablesTi

Opticron BGA 8x42 Lens Cap

This is an eyepiece lens cap for an Opticron 8x42 BGA monocular. The rubber cap supplied with this monocular is very easy to knock off or misplace as it sticks out from the body of the monocular and has no retention mechanism; this print…

Wydruk około 0,65 €–0,80 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
21
Polubienia
1
Ocena
0
P
PrintablesJesseW3D

Pegboard Zeiss Lens Wipe Holder

I printed this on my Prusa Mini+ in PLA with supports everywhere using the 0.20mm STRUCTURAL preset with 20% infill.

Wydruk około 2,22 €–2,71 € nettoWstępna wycena jednego wariantu

Pobrania
20
Polubienia
2
Ocena
0
P
PrintablesPhilo_fo

Lens cap for FUJIFILM X-Half Camera (X-HF1)

I printed it using two color metallic PLA filament and the octagram spiral pattern on the top and bottom. You can obtain the printing setup form the gcode (for Prusa XL) below. The result looks quite good, and given the minimal effort…

Wydruk około 0,41 €–0,50 € nettoWstępna wycena jednego wariantu

Pobrania
19
Polubienia
3
Ocena
0
P
PrintablesJorreto

Soporte AiLens para Cutebot pro

Es un soporte para la cámara Ai Lens de Elecfreaks. Se sujeta sobre el sensor de ultrasonidos del cutebot pro. Se le han añadido un par de orificios para tornillos, pero no es necesario, se sujeta bien. De esta forma se puede llevar el…

Wydruk około 0,81 €–0,99 € nettoWstępna wycena jednego wariantu

Pobrania
17
Polubienia
2
Ocena
0
P
PrintablesGuido3D

Sun filter lenses box

Protecting box for magnetic solar filter lenses This a box that fits foldable magnetic sunfilter. The filter is designed to magnetically connect to eyeglasses models as Carrera (Luxottica). The box can be used to put the folded eyeglasses…

Wydruk około 2,40 €–2,93 € nettoWstępna wycena jednego wariantu

Pobrania
15
Polubienia
2
Ocena
0
P
Printablesimhavoc

43mm-67mm Lens Cap Holder — Thin Camera Straps, 8 Minute Print

Keeps your lens cap on the strap instead of in your pocket, in the bag, or on the floor of a parking lot. Prints in under ten minutes from whatever is left on the spool. Fits — the cap Any 43mm-67mm center-pinch lens cap. Retention is on…

Wydruk około 0,15 €–0,18 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
11
Polubienia
1
Ocena
0
P
Printablescombobulator

Lens Cover for Bosch GTC 400 C Thermal Camera (16055002CR)

Lost the lens cover for my Bosch thermal camera so I decided to recreate it based on photos and share it here in case anybody else needs it. It fits perfectly and follows the original design as closely as it can. There is, however, an…

Wydruk około 0,31 €–0,38 € nettoWstępna wycena jednego wariantu

Pobrania
10
Polubienia
1
Ocena
0
P
PrintablesMatt Boyer

PSVR2 Hanging Lens Cover

A dust cover for your psvr2 PSVR2 Lens Cover

Wydruk około 6,25 €–7,64 € nettoWstępna wycena jednego wariantu

Pobrania
10
Polubienia
3
Ocena
0
P
PrintablesNorberto

Wydruk około 0,17 €–0,21 € nettoWstępna wycena jednego wariantu

Pobrania
10
Polubienia
2
Ocena
0
P
PrintablesJed LaRue

Contact Lenses Box

Contact Lenses Box for traveling.

Wydruk około 1,68 €–2,06 € nettoWstępna wycena jednego wariantu

Pobrania
9
Polubienia
0
Ocena
0
P
Printables3D2H

Carry-on Box - TriShade & CMF Lenses (print in place)

I was looking for a carry-on box for my TriShade design https://www.printables.com/model/1300501-trishade-optimised-light-protection-for-mobile-tri This is the result, including the lenses provided by CMF. NOTE: I don't have the lenses…

Wydruk około 2,57 €–3,14 € nettoWstępna wycena dla PETGMateriał u źródła: PET

Pobrania
7
Polubienia
0
Ocena
0
P
Printables3dstc

stollensohle Handarbeit

für Handarbeitsfiguren ( Fussballer, Sportler ) eine Stollensohle

Wydruk około 0,86 €–1,05 € nettoWstępna wycena jednego wariantu

Pobrania
6
Polubienia
0
Ocena
0
P
PrintablesLXO

Rear lens cap for Sony E-mount

Just as it sounds, it's a rear lens cap for your E-mount lenses. 12 times cheaper than buying it from Sony! Works on my lenses and with my printer but tell me if you believe i should change anything. edit: Added a double mount to be able…

Pobrania
5599
Polubienia
448
Ocena
4,78
P
Printablesyor42

Meta Quest 3 Lens Cover

Basic 3D printable lens cover for Meta Quest 3. It is designed for default facial interface, so it might not fit with other ones. It doesn't block proximity sensor and shouldn't touch lens directly, but I still recommend putting…

Pobrania
4418
Polubienia
445
Ocena
4,97
P
PrintablesPrusa Research

президент тут Volodymyr Zelenskyy Bust

This is a bust of Ukrainian president Volodymyr Zelenskyy in combat gear, who has shown his outstanding leadership skills, resolve and courage during the ongoing Russian invasion of Ukraine. #StandWithUkraine

Pobrania
3232
Polubienia
900
Ocena
4,99
P
PrintablesStepan Broz

Nikon F Lens Cap

What else there is to say? It's a lens cap for the Nikon F mount. You always need one more. Print Settings Rafts: No Supports: No Resolution: .20 Infill: 100% Filament: Filament PM PETG Black Notes: Prints without supports. Extra…

Pobrania
3128
Polubienia
253
Ocena
4,98
P
PrintablesLXO

49mm lens cap

A 49mm lens cap that I made. Works great with my Sony lenses. Be careful to use this lenscap with too rounded lenses as the backside of this lens cap is flat for easier printing. I made a lite version, see "49mm_lenscap_V3_lite.stl" which…

Pobrania
3007
Polubienia
201
Ocena
4,76
P
Printablesvolzotan

Disposable Camera Lens Adapter

They're easy, they're cheap and they can be a lot of fun: disposable cameras. If you still got one around, you can remove the plastic lens from the camera housing and print a lens holder for a Sony E-mount camera. All you need is a bit of…

Pobrania
2879
Polubienia
288
Ocena
4,79
P
PrintablesGyoenastaader

Hadley Mirror and Lens Covers

Update September 12, 2022: Added CAD Step files. Mirror covers for the Hadley. The primary cover can be used for the main mirror, and the bottom of the secondary mirror holder. The web mirror is intended to go on top of the web. The lens…

Pobrania
2604
Polubienia
194
Ocena
4,95
P
PrintablesNominal Brand

Rear lens cap for Canon EOS EF and EF-S lenses

Whether the dog chewed your lens cap, or it fell off a cliff during that last hike, the solution is one print away. Recommendations: Print Material: PLA Infill Percent: 15% Layer height: .15 (a layer height greater than .15 will not work…

Pobrania
2466
Polubienia
495
Ocena
5
P
Printablesckth

Meta Quest 3 Lens Cover

So I wanted to try out modelling the lens cover for the Quest 3 to conform nicely to the default interface but using simpler shapes so it's easier to edit / play around with. NOTE: I've only tried this with the silicon facial interface…

Pobrania
2349
Polubienia
300
Ocena
5
P
PrintablesCypherA7

Spider-Man PS4 Faceshell + Interchangeable Lenses by HappyMoon on Thingiverse

I've seen this Spiderman PS4 faceshell on thingiverse and I wasn't sure if HappyMoon had uploaded it to Printables yet or not so I figured I would share it with this community in case anyone hadn't seen it. It looks like an awesome…

Pobrania
2332
Polubienia
294
Ocena
5
P
Printablesdoroteo

MEDIUM FORMAT CAMERA for MAMIYA PRESS LENSES

Hi! This project is a medium format to be used with Mamiya Press lenses. I uploaded a photo taken with this camera. A Fusion 360 file is attached for you to be able to modify it. The information related to this camera can be found in…

Pobrania
2184
Polubienia
777
Ocena
4
P
PrintablesThomPatterson

Camera Lens Filter Adapter - All Sizes

Why buy multiple filters for all your lenses when you could buy one filter and reuse it for all your lenses. You just need this simple adapter. I've included the two sizes I needed (step-up 49mm to 67mm, step up 43mm to 67mm) which I have…

Pobrania
1987
Polubienia
142
Ocena
5
P
PrintablesFindusdwarf

Pillenspender-Pill Dispenser

Dec 17, 2022 Please read the entire description before downloading! This is a pillbox with 7 compartments for the whole week. Approximately 20mm x 20mm x 136mm in size. For the hinge I use a piece of filament with ø1,75mm that is about…

Pobrania
1748
Polubienia
162
Ocena
4,94
P
Printables3d printing

lens caps

a functional camera lens cap with all sizes for your camera if you lose yours, and is fit for any camera!

Pobrania
1656
Polubienia
830
Ocena
4,89
P
PrintablesMichal Fanta

The Lens Filter Wrench Set

Set of keys to enable filters for camera lenses. 44mm - 52mm 55mm - 62mm 58mm - 67mm 62mm - 77mm 72mm - 82mm 77mm - 86mm 82mm - 95mm Print instructions STL: https://www.myminifactory.com/object/3d-print-lens-filter-wrench-set-52771

Pobrania
1646
Polubienia
224
Ocena
4,94
P
Printablesthenickdude

Sony E/FE lens mount

This is a printable model of the mount found on Sony E/FE lenses, which you can use to design accessories like extension tubes or custom lenses. Print at 0.1mm layer height, in PETG (recommended), PLA, or my pick, ABS. For ABS I had to…

Pobrania
1607
Polubienia
109
Ocena
5
P
PrintablesJP

Canon EF 50mm F1.8 STM Lens Hood

A lens hood for Canon EF 50mm f1.8 STM lenses. Can be used both as as hood and as a protective case. Print Settings Resolution: 0.1mm Infill: 100%

Pobrania
1519
Polubienia
212
Ocena
5
P
Printablessilviu

Canon EOS RF Rear Lens Cap

Overengineered rear lens cap for Canon EOS RF lenses. Missing the align notch and stopper. Print instructions Print .1 or 0.2 mm P.S. Donations welcome, my cat keeps chomping the filament.

Pobrania
1465
Polubienia
126
Ocena
4,91
P
Printablesthenickdude

Canon EF/EF-S lens mount

This is a printable model of the mount found on Canon EF/EF-S lenses, which you can use to design accessories like extension tubes or custom lenses. Print at 0.1mm layer height, in PETG (recommended) or another filament like PLA. This is…

Pobrania
1458
Polubienia
91
Ocena
4,67
P
PrintablesKiril

deep 55mm lens cap

This is a deep easy to handle 55mm lens cap. It is 4 pieces outer shell, buttons with spring, and 2x jaws for each side The lens cap snaps together after printing. Please use PLA and 0.20mm quality settings. See notes for PETG below. To…

Pobrania
1358
Polubienia
112
Ocena
4,79
P
PrintablesMatsErik

Oculus Quest 2 Lens Cover

Designed a lens cover for my lens distance setting. Using the Blender file, you can redesign for yours

Pobrania
1311
Polubienia
235
Ocena
4,75
P
PrintablesSPRKPLG

Ligero69 Camera Body for Mamiya Press lens & M-mount roll/cut film back

Thank you all for the kind messages! Can't wait to see your images, please tag them in social media #ligero69 where possible. Much love! ……… Please note that due to high minimum buys (like 20-100 screws/nuts, etc) the hardware required…

Pobrania
1260
Polubienia
184
Ocena
5
P
PrintablesGiwi

Canon Lens Hood 58mm

This is a Lens Hood for a 58 mm Canon EOS Lens. Suitable for a focal length from circa 18mm

Pobrania
1152
Polubienia
118
Ocena
4,91
P
PrintablesCatdad Workshop

82mm lens cap (print in place)

I recently purchased a well-used camera lens which came with a lens cap that was missing the springs on one side. Seeing as I own a 3D printer and have access to the internet, that should be a not-really-a-problem that is easy to solve. I…

Pobrania
1152
Polubienia
91
Ocena
4,88
P
Printablesyukosteel

Leica M mount 6bit lens coding template

Precise template for 6bit coding of Leica M mount lenses. It's inspired by existing "Leica M Coding Tool" but that one didn't work for me, so I've used caliper to measure Leica M10 mount and designed more precise model from scratch. NOTE:…

Pobrania
1152
Polubienia
34
Ocena
5
P
PrintablesPrintile

Disposable Camera Lens Adapter for Fujifilm (Updated)

Note. You have to salvage a lens from a disposable camera. The one I used is from a Kodak fun saver Update v.1.2: Added a knob to lock the focus and adjusted some dimensions. Find a small screw, glue it to the knob and drill out the hole…

Pobrania
1136
Polubienia
156
Ocena
5
P
PrintablesTim O'Brien

O3 Mod - Lens protection for the DJI O3 Camera. Add to any quad.

Companion project to my other parametric configurable FPV designs: O3 Pod O3 Frame Action2 , 3+4 AcePro GoPro Mini Hero 9-12 Antenna Mount Join my discord to request any custom version! Alternatively use telegram or printables-dm. New: O3…

Pobrania
1074
Polubienia
68
Ocena
4,4
P
PrintablesKatz Creates

Camera Lens Mounted Teleprompter

UPDATE: Thanks to community feedback I have added additional sized inserts for different phones (so there's more of a chance of a snug fit for your phone, but a looser fit is okay long as it doesn't fall out!) as well as a version with…

Pobrania
1052
Polubienia
305
Ocena
4,75
P
Printablestwothingies

Lens Cap Holder for Camera Strap

This is a simple holder for lens caps. Now, you don't have to worry about losing or misplacing your lens covers while on the go. This 3D printable model will keep them safe, secure, and easily accessible. It is a very simple and quick…

Pobrania
1038
Polubienia
316
Ocena
4,95
P
PrintablesSPRKPLG

LigeroLG & GansoLG Camera Body for Lomograflok + Mamiya Press or Polaroid 600SE Lens

Please note that due to high minimum buys (like 20-100 screws/nuts, etc) the hardware required may set you back about $105-135+. With material on top of that, consider buying the real thing at: https://sprkplg.com/product-tag/llg/ If you…

Pobrania
1022
Polubienia
155
Ocena
4,57
P
PrintablesMartunex

Quest 2/3s Lens Protector/Glasses spacer

Remixed quest 2 lens protecor. Print 2 of them and rotate (not in slicer) accordingly to each eye. The glasses spacer/lens protector is design to keep your glasses from rubbing on the lenses causing scratches on them. this is useful if…

Pobrania
1022
Polubienia
87
Ocena
5
P
PrintablesThespianMask

Quest 3 Lens Adapter

This is a lens adapter using the “Quest 3 lens adapter template” by Anonymous Hermit here at Printables, as well as "Oculus prescription lens adaptor" by tanvach over at Thingiverse. Printed with generic white PLA. 100% infill, 0.12 layer…

Pobrania
1008
Polubienia
59
Ocena
0
P
PrintablesBoopidoo

Lens Caps (one part print)

I needed a lens cap for my Raynox-250 macro lens to go with the rear cover I designed earlier. After some modifications to make it easier to adjust dimensions I've uploaded more cap sizes. Print without support. After print, place the cap…

Pobrania
967
Polubienia
152
Ocena
4,96
P
Printableserktheoger

Instax Mini Evo Lens Cap

The cover fits within the standard instax cover, the cover does close completely on the magnet. Printed using voron2.4 Magenta esun ABS, 0.4mm nozzle, print with brim (recommend 3mm), print face down

Pobrania
957
Polubienia
74
Ocena
5
P
Printablesthenickdude

Rear lens cap for Canon EF

Rear lens cap to suit Canon EF and EF-S lenses. Print Settings Supports: No Resolution: 0.2mm Infill: 100% Filament: Plasty Mladeč PLA Black Slicing settings: Perimeters: 2 Seam position: Random The cap has three internal flanges which…

Pobrania
918
Polubienia
82
Ocena
4,91
P
PrintablesBent Derailleur

Nikon Z Rear Lens Cap

Nikon Nikkor Z Rear Lens Cap, original looking but slightly shallower (just because it was not necessary since my design has flat top). Tight fit so it sits secured. Original measurements so it protects whole width of flange. If you like…

Pobrania
915
Polubienia
70
Ocena
4,82
P
PrintablesLXO

Rear lens cap for Pentax K-mount

Just as it sounds, it's a rear lens cap for your K-mount lenses. Works on my lenses and with my printer but tell me if you believe i should change anything. Print Settings Rafts: Doesn't Matter Supports: No

Pobrania
909
Polubienia
82
Ocena
4,91
P
PrintablesSpotmatic

Lens hood 49mm (push on)

A lens hood for your 50mm lens (filter diameter 49mm). No thread - just push on. Use the Fuzzy Skin option in PrusaSlicer if you wish. No support required. Paint the interior matte black. Do you like it? Please consider to buy me a cup…

Pobrania
897
Polubienia
112
Ocena
5
P
PrintablesKrhom

DJI O4: O3 Lens Mod Alignment Jig

Lens Mod Instructions Note If your adapter piece doesn't fit the jig, you might have the slightly different version that's more square. Thankfully, the ever helpful @Tokyo_Dom_663158 made an alternate version of the jig for those!…

Pobrania
885
Polubienia
41
Ocena
3,5
P
PrintablesReallyrapid

GoPro Hero 12/11/10/9 & 11 Mini Lens Cap

I updated my GoPro Hero 8 lens cap for the GoPro Hero 11/10/9 & 11 Mini. This lens cap was designed so that there is a large gap between the lens and the cap so that if any dirt or sand gets trapped in there it wont ruin your lens whitest…

Pobrania
885
Polubienia
158
Ocena
4,89
P
Printablessh

😎 Party fun "nerd" glasses with interchangable lenses (choose your own pattern)

Info: I remodelled original “nerd glasses” from @Miguel (thanks for the model!) the nose area is more comfortable temple hinges are robust, with usage of piece of 1.75 filement as a “screw” UPDATE : i created also temples more angled, so…

Pobrania
884
Polubienia
124
Ocena
5
P
PrintablesThomPatterson

Front Lens Caps - All Sizes

Fully 3D printed spring-fitting front lens caps for every lens with filter sizes from 40.5 mm to 82 mm. Find the filter size you need for your lens (it's likely written on the front of it), then download the “main” and “insert” for that…

Pobrania
880
Polubienia
72
Ocena
4,67
P
PrintablesYalper

Lens cover for DJI Osmo Action 5 Pro

Description: Introducing a cover specifically designed for the DJI Osmo Action 5 Pro. This piece not only provides excellent protection for your device but also features a knurled grip that enhances handling and installation. Features:…

Pobrania
867
Polubienia
62
Ocena
4,83
P
Printableseli

X Mount rear lens cap Fujifilm XF

Design for supportless printing, had tried on XF35mmf1.4, XF56mmf1.2 and XF90mmf2.

Pobrania
860
Polubienia
59
Ocena
5
P
PrintablesLordMelkor

Fuji X-mount Camera Body Lens Cap

Lost the body cap for my fuji x camera, remixed file to recreate the same. Should be comparable to Fujifilm's Camera Body Lens Cap BCP-001 Printed with a 0.6mm nozzle at 0.2mm layer height with support cubic infill for ~35min print time.…

Pobrania
839
Polubienia
28
Ocena
0
P
PrintablesSharkLotus

DJI Goggles 3 Lens Protector

Lens protector for DJI Goggles 3 (May also work with Goggles 2 or Integra but I don't know for sure) Printed in TPU with 40% infill.

Pobrania
829
Polubienia
39
Ocena
5

Single Press Lens Cap

Need: Lens cap that can help prevent scratches and excess dust on the front element. This is my take on a solution to that need. This design uses common springs found in ball point pens. The spring dimensions are 4.5mm Diameter and 18mm…

Pobrania
828
Polubienia
306
Ocena
4,93
P
PrintablesPhysics Dude

Ultra minimal M42 to Nikon F-mount lens adapter

I found an old Carenar lens with a M42x1.0mm threaded mount (not to be confused with T-mount which is a M42x0.75mm thread) that I wanted to use with my Nikon DSLR, but the only adapter I found claimed “INFINITY Focus NOT ALLOWED.” This is…

Pobrania
827
Polubienia
74
Ocena
4,67
P
PrintablesAnonymousHermit

Quest 3 lens adapter template

Edit 2023-10-21: Q3 Lens Adapter Template V2 I noticed that the ridge by the nose is actually curved. That curve is now incorporated so the adapter sits flush. --- This fits into the Quest 3 lens well. Bring your own lens adapter or just…

Pobrania
822
Polubienia
43
Ocena
0
P
PrintablesDesignLabX

HuskyLens Case

This is a 2-part snap-together protective case for the HuskyLens AI vision sensor v1.1. The case & camera can be mounted with M3 screws. Holes in front are for bilateral white LEDs, RGB LED and lens. Raised arcs on top protect the control…

Pobrania
821
Polubienia
13
Ocena
0
P
Printablescolinhalebrown

Canon EF Lens to Sony E-Mount Body

Adapts Canon EF/ EF-S lenses to Sony E-Mount bodies. That is all, no lock, no frills.

Pobrania
821
Polubienia
28
Ocena
0
P
PrintablesColgS3b

Nikon lens end cap F mount

Cover for the mount side of Nikon lenses. Tested with: AF-S NIKKOR 16-80mm 1:2.8-4E ED NIKKOR-S Auto 1:1.4 f=50mm NIKKOR-Q Auto 1:3.5 f=135mm Rokinon 1:1.4/85mm AS IF UMC Designed in FreeCAD Print instructions Print with the open side up.…

Pobrania
817
Polubienia
72
Ocena
4,4
P
Printablesairpipelab

Fresnel Lens

I designed the Fresnel lens in solidworks, it's show the fresnel lens about principles of physics. if you have any question about fresnel lens principles of physics ,please contact Mr. David. [email protected].

Pobrania
802
Polubienia
27
Ocena
5
P
PrintablesSeko

LUMIX L-Mount Lens Cap

UPDATE: Ver5 with Lumix written on the inside and some adjustments for a better fit. Tested on native Lumix lenses and K&F Lens Mount Adapters.

Pobrania
788
Polubienia
46
Ocena
3
P
PrintablesSpielkind

Samy the spectacled snake - Samy die Brillenschlange

Samy the spectacled snake Ich wollte einen einfach zu handhabenen Brillenhalter den mann gerne anschaut. Und so entstand Samy. Vergesst bitte nicht den Like, wenn er euch gefällt. Ich hoffe Ihr habt auch Spass mit Samy.…

Pobrania
787
Polubienia
126
Ocena
5
P
PrintablesChrisE

Lens Cases for Canon EF-M / Canister Set

Update Feb25: Thanks for almost 300 downloads! Full Step Files available for Purchase from my Printables Store Here - perfect for alteration and customization. Free STL Files for 3D Printing below: Set of Modular Lens Cases, Protection…

Pobrania
771
Polubienia
198
Ocena
5
P

Pi Camera Lens Focus Adjustment Tool

Focus adjustment tool for Raspberry Pi Camera V2 Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 50% Category: 3D Printing

Pobrania
756
Polubienia
33
Ocena
4,8
P
Printablesjay16799

Bahtinov Mask for 18-55mm Lenses

Summary of Concept This is a 3D printable Bahtinov Mask to assist with manually focusing on the night sky. Bahtinov masks work by creating diffraction spikes from a point light source (like a star) spread out across different sections of…

Pobrania
756
Polubienia
54
Ocena
5
P
Printablessowa705

52mm lens cap (improved version)

Improved version of my older 52mm lens cap. Prints in just two parts and clips together without screws or springs. Designed for PLA+ filament and requires supports. Print one 1x body with your selected design and 1x spring

Pobrania
754
Polubienia
65
Ocena
5