First layer test 150X150 - 150X180 - 50x50
First layer 150x150 0.2H First layer 150x180 0.2H First layer 50x50 0.2H
- Pobrania
- 690
- Polubienia
- 21
- Ocena
- 5
167 modeli
First layer 150x150 0.2H First layer 150x180 0.2H First layer 50x50 0.2H
Made for 75mm wide sandpaper. Print instructions 3-4 perimeters 15% infill
This is more or less influenced by many tablet stands out there, the design is not that complex or unique. It is quite big, I designed it for a 13" drawing tablet that my wife uses. The outer dimensions are 200 mm wide and 150 mm high.…
You can use these squares to easily level your bed. Print them out and then adjust each corner individually. If the surface is rough, lower that corner and if it's not sticking at all or you see gaps between the lines, then raise that…
New and bigger stackable organizer what can be attached to the other ones. Everything is easy to print, without supports, There are 3 different drawer available : Update : 31.01.2021 added picture from the box 01.02.2021 made a bit…
No support is required if pot and feet are printed separately. However, both parts must then be glued together. A model has also been added where everything is in one piece, support is required here.
Bonsai display table 09 square 150x150x37mm, support is necessary. Feel free to scale up or down until you like the result and it suits your tree.
To assemble the clips and connect the lid to the bottom of the box, 6pcs of M3 30mm screws must be used.
Bonsai display table (No. 05) rectangular 240x150x35 mm, best for bonsais with rectangular or oval pots. Feel free to scale up or downn until you like the result and it suits your tree.
Very stable bracket 150x150mm with four screws (4mm) on each side for the perfect fastening
Passt viel rein, lässt sich stapeln
Bonsai pot 29 round conical 150x150x70mm, no support is required if pot and feet are printed separately. However, both parts must then be glued together. A model has also been added where everything is in one piece, support is required…
Step file included, so you can push/pull the bottom face to the distance of your liking. M3 x 10mm bolts and nuts for permanent installation. Dremel or similar to drill 3mm holes. Printing orientation for the joints: vertical, with brims…
A very simple, but also very useful wall holder for the Bosch GEX150 Turbo random orbit sander. Prints easily without supports. I opted for 0.3mm layer height using the standard 0.4mm nozzle. Use countersunk screws for mounting to the…
I created a bigger storage box for my workshop, that I use mainly as bin on my desk.
1st layer test by 0.2 layer height
Two concentric squares to check if your buildplate is level or warped. Fast to print. Use this test print to check if your printbed is level and adjust your first layer height. The outer square is 150mmx150mm. Make sure to take a look at…
Designed a corner expansion for 4mm corrugated carton boxes. Just adjust the heigh in prusa slicer on for your box height. I suggest to put tape around it to increase toughness so it won't fall off easily. Everything shown in photo. Mine…
Wall-hanging double shelf with Honeycomb Storage Wall (HSW) sides to store more things.
This is a remake of Wivry's box. Size chosen to fully utilize the available Bambu P1P plate size. (For utilizing the full 256x256 plate size, see instructions ) Height was chosen to coincide the official LEGO box height (150mm) You can…
Godzilla doesn't care about your holiday! Remixed this excellent coaster design into a Chroma Canvas image using black, bronze, tan, and white filament in a 150mm x 150mm square, which should leave plenty of frames to choose from. :) If…
150x150mm 1 layer test print
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #15 (1.22mm) swap to Orange At layer…
Customizable Sizes for Every Need My boxes come in a wide range of sizes to suit different needs. They are available from a compact size of 40x40x10 mm to a larger size of 150x150x150 mm. These boxes are provided with increments of 5mm,…
Instructions: Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #8 (0.66mm) swap to Jade White
This is an adapter to mount a TV with a 200mmx150mm VESA hole pattern to a mount with 100mmx100mm or 75mmx75mm pattern. I bought a small 32" TV for my office, and also got a cheap wall mount that said it supported 32" TVs, however the…
I created a frame specially designed for square photographs of size 150x150 mm. It is in two parts so that the two pieces fit together.
Customizable Sizes for Every Need My boxes come in a wide range of sizes to suit different needs. They are available from a compact size of 40x40x10 mm to a larger size of 150x150x150 mm. These boxes are provided with increments of 5mm,…
The frame is suitable for artworks of 150x150mm, the thickness of the artwork is within 2mm, and the viewing range is 146x146mm. If the frame needs to be placed on the desktop, please print the Support file.
Floating Shelf designed with TinkerCAD. Single file print, one model. --Recommended Settings-- Printed with Anycubic Kobra 2 Slicer: PrusaSlicer (Anycubic Kobra 2 Preset) Supports: None Req'd Brim: Yes Material: OVERTURE Black PLA Infill:…
To mark a center, or cross cut, you need to print, two pins. Pins should be printed with 100 infill.
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #15 (1.22mm) swap to Blue At layer #17…
A stackable Box with an optional inlay and a separator that allows to divide the box in multiple compartments. I printed all the parts without support, although the rim at the bottom may need a support. All the parts have a good fit, but…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #15 (1.22mm) swap to Blue At layer #17…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #16 (1.3mm) swap to Purple At layer #20…
Print a back piece and then the frame itself, then sandwich the picture between them. You can use superglue to adhere the pieces together. The frames look especially nice if you use one of those carbon fiber smooth plates. Textured plates…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #16 (1.3mm) swap to Red At layer #20…
to store mini stuff under the desk and free up some space on it
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1 mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Black At layer #15 (1.22mm) swap to Orange At layer…
Couldn't find any frames I liked for some hueforge prints I did, so I created my own with a snap fit back. Theres also a recessed area if you want to include a note or business card inside the print. Fits 150x150mm. Note: The printed part…
Self standing photo frame, vertical or horizontal. Easy to print without supports. Material PLA or PETG. Printing time 26 minutes, filament 7.37g
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #7 (0.58mm) swap to Jade White At layer #14 (1.14mm) swap to Lavender Purple for the rest.
Customizable Sizes for Every Need My boxes come in a wide range of sizes to suit different needs. They are available from a compact size of 40x40x10 mm to a larger size of 150x150x150 mm. These boxes are provided with increments of 5mm,…
(Bigger) Basket with Hexagons/Honeycomb | 150x150x110mm note: There are 2 versions: 1 with handle cutouts - and 1 without!
I needed an electronics box to house my rather long 3-fase 4-way switch to switch my heavy equipment behind a rpm controller. This box is 190mm wide, 110mm high, and 150mm deep. (can fit equipment less then ~140mm long). The hole are easy…
Its a 2mm thick aquarium lid. Size 300x150mm is the size of an aquarium. It was created for the Akvárium ANTE with the lid, so it has wider frame on the sides to cover the original frame.…
Calibration across a long range will allow for greater accuracy than typical 20x cubes. This corner is 150mm in each direction, and also includes cutouts in each orientation to allow measuring for internal accuracies as well. 5 and 10mm…
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #8 (0.58mm) swap to Dark Gray At layer #11 (0.9mm) swap to Gray At layer #19 (1.54mm) swap to White for the rest.
This is a remix of a stop angle from KeuleDidi. Unlike the original, i attached a scale for rough measurements and made a hole in the corner like an original made of metal to be able to position the angle better. The scale shows full and…
250x150 Schild für die Auffahrt in 2 Versionen Löcher für M3 Schrauben…
A simple tray for pin punches. It fits 6 pieces of octagonal 10x500 mm pin punches. The grip side has a recess so you can push them down on either side to take them out. Size is 4x2x3u and is stackable. Printing your favourite gridfinity…
Oval bonsai pot, shohin-sized, 190x150x58 mm, print feets separatly and glue it to the bottom or print the whole model with support.
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Swap Instructions: Start with Black At layer #6 (0.56mm) swap to Jade White At layer #13 (1.12mm) swap to Black At layer #15 (1.28mm) swap to Red At layer #19…
Dvě poličky, které když se dají vedle sebe, zaberou celou šířku jedné desky děrované stěny Mars. Proto mají rozměry 197x150x50 mm. Samozřejmě se dá vytisknout i jen jedna. Doporučuji tisknout s podpěrami vzadu (na “háčky”). Toto konkrétně…
Simple medicine box, the bottom left sections are for the 3 parts of the day, the rest are for classifying their boxes
EN: Custom sorting boxes fot workshop tools trolleys 3 sizes: 75x75x45mm 150x75x45mm 150x150x45mm The height is actually 43mm to fit felt drawer insert. Practical plastic sorting box for storing small parts such as nuts, screws, dowels,…
XY Calibration Cross 150x150mm Category: 3D Printing Tests
Another desiccant box. Sturdy design, snap on lid, lots of vents, holds lots of beads. Recommend printing with 4 perimeters in PETG. I'm able to put the whole box in my dehydrator oven for several hours with no problems. There is an…
This model is a stand designed for 130×150 mm solar panels, which you can commonly find online. You can use two pieces per solar panel and screw them onto any surface. I recommend using a heat-resistant filament for this design, as the…
Grille 150x150 honeycomb/Maskownica 150x150 plaster miodu otwory montazowe fi 6
Printed from Prusament PC blend. New one fits tighter to the metal part. It is recommend to pour the printed part in boiling water to avoid breaking it while installing.
A simple vented funnel I printed to help with mower oil changes. 150mm across, 150mm tall, 20mm across at bottom. Wall is 3mm thick. Print wide end down, no supports needed. Fusion 360 source and .STEP file included.
Same thing as the original just slightly narrower to fit a 150x150 bild plate
I wanted to mount my router on two pipes that go from floor to ceiling in my apartment. The pipes are 21mm in diameter and spaced 45mm apart. The routers mount holes are ~160mm apart. Warning: ‘Low’ tolerance on the mount between the two…
180 mm x 150 mm Skimmer Stand Total Height 86 mm (76 mm legs, 10 mm thickness of platform) Honeycomb Pores Round Legs Designed for Reef Breeders RR-150 Skimmer (Reef Rhythms series)
2D ornament split into parts with mounting holes and flat pins for easy connection of the individual ornament sections. ZIP folder contains stored in STL 1.X203xY2xZ150 2.X203xY2xZ150 3.X200xY2xZ150 Redistribution of the 3D STL files is…
Trampilla de techo 150x150 mm. Ideal usar iman de neodimio
Print at 100% infill with a layer height of 0.08mm with a base layer of 0.1mm Swap Instructions: Start with Black At layer #8 (0.58mm) swap to Dark Gray At layer #11 (0.9mm) swap to Gray At layer #19 (1.54mm) swap to White for the rest.
A new size for this great model. Thank you to the creator.
12x150mm thru axle mount (rear) the blocks can be connected to each other with M6 bolt 30mmde blokken zijn onderling te koppelen met M6 bout 30mm
Deco X1500 Wand und Decken Halterung mit Decken Halterung Option Oder auch als POE variante für ein 12v POE Adapter Deco X1500 3x Set: https://www.amazon.de/dp/B0CL573PRH?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2&th=1 POE Adapter Mit…
This is a universal 150x150 mm storage organizer with a convenient label slot on the front, designed to help you keep your workspace tidy. It’s ideal for PEX pipe holders , small parts, screws, or any other items that tend to clutter your…
Just a simple box I designed in Fusion 360. I intend to use it as an divider or extra shelf space by laying it on one side onto a larger shelf - but since it has a bottom it can be used as a "normal" container as well. Fusion 360 file is…
BE VERY CAREFUL WITH THE POWER BUTTON WHEN INSERTING THIS INTO THE CASE! uses 4 screws: M 2.5 x 6 https://www.sparkfun.com/sparkfun-micro-oled-breakout-qwiic-lcd-22495.html I removed the the thicker double sided tape from the oled and…
Complete rebuild of the Grrp Neo / X150 Enables features like Display, SD Card support, heated bed, Power switch, increases the print speed due to better cooling ( 150mm/s ), silent. Added 3dm source files for modification. Print…
Air ventilation grid 150x150 (inner part 110x110)
This model is a HueForge illustration of Frieren. Her heart may belong to Himmel… but she has mine. Two versions are included : 200x200mm 150x150mm (for A1 users) Print profiles are included for both AMS users and manual filament swaps…
For SFX-100 or DIY sim rig motion platform builders, this is designed to help mount a GX150 linear bearing rail to aluminum extrusion. Example GX150 rail here: https://www.aliexpress.us/item/2255800831885842.html *note: these can be…
3D printed box. Print with standard parameter.
Lithophane box 150x150 mm Very large lithophane box . It should make lithophanes of 150x150 x 4 mm. The bottom part is to be able to coil cables and make connections. enclosed part for G9 type lamp holder.
This is flap for Vagner pool VA 150x150 skimmer - used for thin wall pools. Basic flap dimensions are 146x120x22mm. My printing setup: Material: Prusament PETG or ASA Nozzle diameter: 0.4 mm Layer height: 0.2 mm SPEED Infill density: 100%…
WICHTIG: Die Kugel muss nach dem Druck einen Durchmesser von 1" / 25,4mm (+/- 0,1) haben. Rechteckige Klebebasis mit B Kugel. Klebeband: 3M VHB Printer: Bambulab X1E Material: ABS Layerhight: 0,2mm Infill: 100%
For card game Bang! Insert organizer for 226x150mm box for 57x86 card
Simple slim tray for instruments or scrap :) length - 20 cm - 7.87 inch width - 15 cm - 5.9 inch height - 1.2 cm - 0.5 inch
Test Level plate 150x150x0.6, with some text. Text on the underside helps you check quality
Grille aeration 250x150 mm Cotes encastrement : 220x120 mm. Imprimé en PLA ,0.2 mm de couche. Avec radeau sans supports.
Enjoy a photo of my tiny old orchid. 90mm diameter x 150mm height Recommended printing settings: Material: PETG (I used a blue-translucent one) Layer height: 0.2mm is fine Infill: 0%-15% infill Perimeters: 2-3 Outer brim: 10mm width,…
Simple backplate to cover old thermostat holes/locations using a 150x120 backplate.
a remix for a 150x150 glass plate
🇨🇿 Český popis Polička do grow boxu na 16mm tyč (150 × 150 mm) Kompaktní a pevná polička navržená pro grow boxy s 16mm konstrukčními tyčemi. Ideální pro umístění teploměru, vlhkoměru, malého větráčku nebo dalších doplňků. Polička má…
Little catching tray for the water dripping down from drying tray As a sort of topper/grid to place the stuff to be dried on I just used a 150x180mm rectangle without top and bottom layer to reveal the infill and let the water drip through
Arm with a deeper (18mm) hook for Adjustable Tablet Stand 200x150mm by Tim A. https://www.printables.com/model/256993-adjustable-tablet-stand-200x150mm Print two of them. I recommend flipping one over so the outer/inner textures are…
Took the two by two file he had and created a 150mm by 150mm tile that will allow those will tiny printers like mine to print sections of this peg board. Shout out to LittleGreenFire!!! I will post photos as soon as I can get this little…
printed in prusament PLA galaxy black, 0,2mm
PETG Print Settings: 0.04mm Layer height 3 Walls 5 Top and Bottom shell layers 15% infill IMPORTANT: If your filament is semi-transparent, then use the “thick” version as it otherwise would be kind of transparent and look bad as you'd see…