19 modeli
This spool holder will hold up to a 168mm wide spool. It uses 4 608 skateboard bearings with a low tolerance/loose fit on the actual rollers but it fits tight with a small bit of force required to slot them in. if you have strength issues…
Video Build Series https://www.youtube.com/playlist?list=PLP1eNQyjgIM5fTi6UlVvp_qiRU6pLUt3n This is a remix of the HEVO, and you will need to download any files not listed here. https://www.thingiverse.com/thing:2254103 . It is built with…
Spool holder for 5kg spools of filament from Zyltech. May also fit 5kg or 3kg spools from other vendors. Print on the flared knob end with a brim. I used PLA and it's fine, but may be printed with PETG if so desired. After printing,…
Zyltech's Filament Rolls are too big to fit on the AMS Lite. I created a simple adapter to go from 73mm to 57.5 MM which will keep the roll on the AMS Lite without any issues. If the cap is a little tight, scale it to 102% on X and Y.
I recommend 10 walls and 55% infill for this spool holder since it'll be carrying 5kg spools. It will almost certainly hold the weight with less structure than that, but I prefer it to be beefy. Print this model laying flat with the legs…
I recently bought a 12V 30A power supply from Zyltech to replace the old stock 20A one on my printer that ran rather hot. The Zytech one is much nicer, quiet and runs cool, but I needed a cover for the wiring. I wanted it to hold my power…
This is for the spools from China that have the massive center hole. This is a fast print that allows you to adapt it to a more normal size spool holder.
Redesigned D-Bot Lead Screw Bracket using Zyltech Anti-Backlash Nuts. Uses same bolts, nuts, and washers as the original D-Bot bracket. Based on https://www.thingiverse.com/thing:1860005 by TheLost Category: 3D Printer Parts
Like the Zyltech 5kg Texas Size spool holder but want to use other brands as well? Well here you go, since the adapters that come with the holder wont work as well for other brands spools I designed one from scratch and have included the…
I went through the ZYLtech catalogue and made a swatch of every different filament they offer. Each material has the manufacturer's recommended hotend temperatures on it.
The Zyltech Gear comes with a synchronized dual Z axis setup, but the lead screw nuts are anchored onto the bracket, not allowing for any play and ultimately leading to Z banding issues. This floating z bracket setup mimics the Artillery…
A simple fan duct designed to mount a 5015 blower fan and direct it's air over the stepper drivers on a Zyltech Gear 3D printer. The duct slips over the outlet of the fan, and a longer m3 bolt is used to replace the top left board bolt to…
Hygrometer adapter for Zyltech spools. After aligning the hygrometer tabs with the adapter cutouts, push all the way in and twist. The part has a small lip inside that should allow the hygrometer to stay in place. Here is a link to the…
This is a basic, but working z axis belt bracket for the alignment leads on the Z axis screws. Reuse hardware and bolts. Print in PETG or ABS.
This is an automatic bed level for the ZYLTech Gear v3. I use this solution for bed leveling on several of my other brand printers. The concept is based off the FreeABL by stevohen (for Creality printers). I designed this mount and clip…
Simple adapter to properly mount a Creality CR10 light bar kit onto the Zyltech Gear 3D printer. The top bar on the Gear is exactly 20mm shorter, so these brackets add 10mm to either side. The Gear's top bar also isn't tapped for m5…
This is an improvement to my previous direct drive extruder for the ZYLTech Gear and probably the Two Trees BLU series. (The factory mount of the printer is posted as well, so you can compare it to your printer.) This mount will work with…
Upgrade to a direct drive extruder for a E3D style round hot end with one or two 5010 blower fans for the ZYLTech Gear. This is a simple way to upgrade the stock extruder motor to a direct drive configuration as well as replacing the hot…
I designed a clip-on filament guide for the ZYLTech Gear v3. It will help keep the filament in line and out of the way. Print Settings Printer: ZYLTech Gear v3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 10% Filament: ZYLTech PLA…
