Liczymy pasujące modele…
Bitcoin Shutter Shades! Perfect for any bitcoiner to celebrate Bitcoin's journey to $100k. Simple assembly: just print the pieces, snap them together, and secure them with a bit of raw filament.
Wydruk około 0,81 €–0,98 € nettoWstępna wycena jednego wariantu
Heavy duty wall bracket for shelves. When properly attached and shelf no longer than 35cm, the bracket can hold up to 100kg. (I carefully hung onto one of it with my body weight and it held without any problems. The holder can certainly…
AFAIK the most common Italian WW2 bomb, used in all of their bombers like the S.79, Z.1007, etc. Scaled 1/72 (assuming the real bomb was 130cm tall). I am not sure about the shape, perhaps looks slightly too slim compared to photos, but…
Had a pile of these thermistors sitting around in my drawer from my old ender and decided to repurpose them as a chamber temperature sensor for my Voron 2.4 Designed to fit on any 2020 extrusion and includes a raised section on the bottom…
Mount for a Chamber Temp Sensor (NTC 100K 5x25mm) Uses an M6x12 Screw and M6 T-Nut to mount
I redesigned the chamber thermistor mount to have the thermistor and wire outputs be opposite instead of at a right angle to each other. This is better for my use case, as it allows me to mount it on the bottom back extrusion of my Voron…
A tiny mount for a NTC 100K 3950 temperature sensor. BOM 1x M3x6 FHCS
Mercedes avtr concept thanks 100k
i have nothing to say:) just a tiny yt playbutton compared to my original. Disclaimer: This model is an unofficial replica of the YouTube 100K subscriber playbutton. It is made for collectible purposes only and is not affiliated with…
Enclosure to hold a 100kg flat load cell. This enclosure provides the actuation point for the load cell. This is designed with a lip to be placed under a bed foot or similar. This was designed specifically for the uxcell 100kg…
Mounts to 4040 extrusion using M4 bolts and T nuts. I used countersunk bolts for a flush finish. Print in PETG / ABS / ASA or any high(er) temperature filament. Built and available on OnShape if you need to make adjustments.
Based on this tiny image and my boundless imagination. Minimal supports required.
This is a Roblox 100k Award I originally designed for JackSucksAtLife but never got round to sending it to him. This should be a 1:1 scale of the real one!
Take your finger strength to the next level with this modular 3D-printable edge trainer , designed for progressive climbing training at home or in the gym. This compact edge block features four precision edge depths : 10 mm – Micro edge…
If you get these from amazon they were 50 degrees off for me and I spent 2 days calibrating them, after calibrating I could print PLA as normal instead of at 220c and now I can get the wood grain effect with my wood filament.. If you…
Want some ultimate swag for the BTC100K-party that you're going to? Look no further. It prints in less than two hours and can be assembled with a flat head screw driver. Please make sure that you have a clean printbed with an adhesion…
This linear connector is very strong and can withstand loads of over 100 kg in peek, and 30kg in long time. Your printout may not withstand the maximum load values indicated above.
Does this feel like a ginormous milestone? Yes. This is something never to be forgotten, that's why I wanted to print a plaque.
NTC 100k 3950 Glass Thermistor Chamber Sensor Mount ADAPTIVE FAN
A mount for the Quantum Fiber/AT&T Q100k Smart NID. There may be other Fiber providers which use this, although these are the two that I am aware of. This Mount replaces one of the Side panels of the Mod10 10" server rack and allows for…
Take your finger strength to the next level with this modular 3D-printable edge trainer , designed for progressive climbing training at home or in the gym. This compact edge block features four precision edge depths : 10 mm – Micro edge…
