Liczymy pasujące modele…
Wall mount for Lego Oracle Red Bull Racing RB20 F1 set 42206. This mount uses two gray pins on the bottom of the F1 to hold. You can easily see this pins trough the seat for easy hanging. Print settings: Infill: 30% 3D gyroid Perimeters: 3
As seen on YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
This model is compatible with the lego system.
Ersatz Gummipuffer Heckklappe am Megane 2 Coupe Cabriolet. Da dieses seid Jahren schon nicht mehr bei Renault verfügbar ist, habe ich selber einen Designend. Die Montage ist etwas unentspannt, da die Aufnahme sehr eng ist. Mit etwas…
LEGO® Technic 42206 red bull racing F1 wall mount
Skadis wall mount for Oracle Red Bull Racing RB20 F1 Lego Car (42206) The hooks for mounting can be downloaded from the original upload
I used two EZ Ancor drywall screws to secure the bracket to the sheetrock without blocking behind. One thing I really like about the hook is that you have to press the car suspension down a little to catch the hooks and gravity does the…
I modified a chin mount model posted by using a much more detailed scan to capture data. The helmet was scanned with a Metro X scanner in feature tracking mode due to me being too lazy to use the lazer mode. I have also attached the…
This is a custom-designed wall mount specifically engineered for large-scale Lego Technic Formula 1 models (such as the 1:8 or 1:10 scales). The goal was to create a secure, almost invisible solution that showcases the car's silhouette…
Here is a vertical wall mount for the new Redbull F1 Car. To make the mount work, you need to get 3 pieces from Lego or print them yourself. To print the two axles and the technic bar, the layer width needs to be no greater than 0.26 with…
A waveform generator, Arduino driven. The well known XR2206 is creating sine, triangle, quare, pwm and ramp signals. The generator provides TTL signal and a 50 Ohms output with an amplitude up to 5V +-. More details of the build can be…
Small Propulsion Pod for 2206 Brushless Motor for Hand Chuck or Single motor to Twin Conversion. For Flat bottom airfoils. Includes cowl. Has ventilation. I designed this specifically to fit and convert my CG-4A Waco glider from…
Introduction My DIY kit came with box components but they can't have worked, ever. The original box does not allow for how tall the 10-µF capacitors are. The original sides allow only 10mm, while the caps measure over 12 mm and the…
Inspired by https://www.thingiverse.com/thing:4682298 OEM Part: https://www.whirlpoolparts.com/PartDetail/Dispenser-Tray/WP2206670B/826974 Our refrigerator's drip tray was starting to show its age, and had calcium deposits that were…
The bottom half of the case for Philips TAT2206. So if your break you can replace it.
not everyone can pierce the covers to attach the sensor. Then you can screw the Smart TLC 2206 WiFi sensor which is used to measure the water level of a tub. Normally you drill a hole in the cover and screw the sensor. Instead, with this…
Bottom of VESA pads is countersunk to allow using socket head bolts with nuts. All holes are configured to 5.4mm to use heat set inserts like the original. If you want to use nuts for the VESA mount, change the holes in Sketch1 in Fusion…
A quick scan of my AGV K3's Top Vent, as I managed to slightly chip the vent on the other side. The included model is from the rider's right vent. Mirror in the slicer if you need to repair the left vent.
Had problems getting the bell off of a damaged 2206 drone motor. I created this very simple jig. Slide the drone motor in until the bottom of the bell hits the inside lip. Turn upside down and use a block of wood and lightly tap with a…
A wall or post bracket for the Tuya TLC2206 ultrasonic tank-level sensor (sold by EPTTECH, Wi-Fi or Zigbee). The sensor needs to look straight down at the water with nothing in the way: this holder keeps it flat in a ring, about 5 cm out…
Kobe Red Line GD2206L toolbox organiser space for 5x2mm magnets in bottom to secure inside metal toolbox No supports needed
I laser scan of the chin guard that can work with my AGV K3 helmet. Sh*t helmet. I hate it. Get a Bell Race Star. Anyhow, this scan exists. Use it as you please. I trimmed and removed the fabric part of the chin guard that hangs out to…
I used two EZ Ancor drywall screws to secure the bracket to the sheetrock without blocking behind. One thing I really like about the hook is that you have to press the car suspension down a little to catch the hooks and gravity does the…
This is a custom-designed wall mount specifically engineered for large-scale Lego Technic Formula 1 models (such as the 1:8 or 1:10 scales). The goal was to create a secure, almost invisible solution that showcases the car's silhouette…
This model is compatible with the lego system.
