Liczymy pasujące modele…
I wanted to get my laptops out of the way (usually piling up on a table somewhere) and so created some fall mount brackets. I needed them to be sturdy, low profile, but also to allow charging when ‘docked’. Print settings: PETG 0.4mm…
I saw other similar ones but this one is less likely to break than those.
Could not find a mount for the MX5300 Wifi 6 so I modeled up my own. I just added a corner mount for the mesh routers too. I did use supports on this mount for the long overhang. Print instructions I printed without supports and it works.…
Support pour positionner un Dell Latitude 5300 verticalement sur une station d'accueil Dell WD19 ou WD19TB. Fonctionne aussi avec les Latitude 5400, 5401, 5410 (tous ceux de 21 mm d'épaisseur). Print instructions Impression en PLA, à…
Hey my 3D-Friends! I have designed a easy wall mount for these ASUS-Routers: GT-AX11000 RT-AC5300 GT-AC5300 Here you find only the Wall Mount Screw Template, just for testing. The Wall Mount Plate do you find here:…
Print from PETG, ABS or other heat resistant material. For this piece use clear see through filament because of the LED. Original switch part number: 61318365300.
Shaped to hold a Nikon D5300 camera. Fits other D5X00 series cameras as well probably.
The original button broke. Replacement cost is prohibitive (30$ on Amazon !!!). Category: Replacement Parts
The design is meant to be used with M6 screws from the rack. It was originally printed in PLA, which turned out to be stronger than the original material. Update : The PLA did not withstand the stress, and I encountered difficulties…
Printed in PLA I painted the backdrop of my logo silver. Print back down with supports to allow for the logo to have good quality. Place a 2x4 brick into the model when finished printing to connect to tie fighter.
Sometimes you want to use you're strap. Some times you don't. Therefore I created the DSLR Strap clamp! Please note I have made the strap clamp originally for the Eos100d/Rebel SL1 other straps maybe to wide or to narrow. These files are…
I wanted a wall mount that keeps the router a little further away from the wall surface, to help with signal reflection and obstruction as much as possible. I used random #8 wood screws that I had on hand. One screw is likely enough to…
This Printable contains two simple mounts for the Catalex MP3 player, a board for the serial-controlled YX5300 MP3 chip. The Catalex attaches to either of the mounts with two to four M2 x 5 mm screws (you might be able to use M2.5 x 5,…
The Yellow Jaw in the pictures is the Stock Jaw… The Green Jaw is the Printed replacement.
This is a replacement rear port cover for an Apple PowerBook 5300 series laptop.
These are various replacement plastic mounts, etc for the pieces that normally break off on an Apple PowerBook 5300 series laptop.
This is a recreation of the bottom bed roller (not side rail roller) of Apache Campers made 1973 - 1986. Made it based on dimensions taken from a “new” bed roller. For best results I would print this out of a durable material, PETG,…
Based on the classic Rugged Box by Whity , and heavily inspired by David's Travel Case for Sonicare 4500 . Designed for traveling with Philips Sonicare 5300 toothbrush. While there are some designs on the web already, unlike this design,…
I needed to create a solution using my Logitech Z-5300 5.1 speakers on my desk, and I realized these do not exist. After some time and many iterations later, I present to you interfaces for a long discontinued Logitech Z-5300 speaker set.…
Required parts: M3 screw, nut(any kind) and washer(preferably plastic to avoid scratching) Both pieces from the STL Superglue A piece of paper if you use a metal washer and you're worried about scratching Here's a guide on how to apply…
What Is It? If the ball socket on the back of your Samsung EP-H5300 car charger for Galaxy Flip and Fold broke off (mine broke in half), then this is a drop in replacement. The rear of the charger where the old socket fits in has a keyed…
Auffangeinsatz für Stapelstation Rimage 5300 CD Procucer
Replaces the existing power cord plate or one of the blank plates on a PVM-5300 with an IEC C14 socket adapter. I did not add holes for the actual socket since, while the main hole is very consistent across different brands, the mounting…
Remix for the 5300 series (HX710B). It fits tightly so that it does not rattle. Printed on Bambulab A1 with PETG. 0.2mm layer height with 0.4 nozzle.
Philips Sonicare 5300 toothbrush holder with charger for 4pcs you will need some screws and cable ties
I remixed this a bit to have grooves to make removal easier, adds some grip. Category: Tool Holders & Boxes
This is a cable entry gland plate for an RS PRO 7755300 painted steel enclosure. The design may work for other enclosures with similarly sized gland plates. Heat set inserts in the plate attach the plate to the enclosure. I printed the…
These anti cat spikes may stop your cat sitting on your nice warm router. They also may not. They might end up being used as a scratch post - who knows? The model base is a 160mm square to fit the venting on the top of an Asus RT-AC5300
