Liczymy pasujące modele…
Model have 8 slots for 3x1,5mm circular neodymium magnets(press fitted). 2 parts of the case are held together with 3 M2x10 screws and M2 heat set inserts (3,5mm OD, 3mm height).
Wydruk około 0,34 €–0,42 € nettoWstępna wycena jednego wariantu
Even after 5 times of printing the AngryCam OV5640 mount of "chri.kai.in" I could not get the thing to print and fit together correctly. The tolerances seem quite tight and you need an extremely precise printer to get good results. Apart…
Locking device to lock clutch housing, used on BMW R1150 motorcycles. BMW part number - 11 5 640. Printed in 100% infill with PETG. Works and holds perfectly, even with those five 40Nm and 32° torque settings for flywheel bolts.
Voron v0.2 OV5640 camera mount. (100 degree AF on picture) No supports needed. (Voron v0.1) Depending on your bed adhesion a brim.
Snap fit case for "New OV5640 ESP32 CAM Camera Module Kit WiFi Bluetooth Development Board (shown in picture)". I bought this board at AliExpress.…
case for HBV 5640 eg Voron 2.4 ---- BOM: 4x M3x10 or M3x12 2x M3x5x4 insert 3x M2x4 tapping screw to mount the cam ----
Just remixed cover to uncover the LED light. Used camera: https://s.click.aliexpress.com/e/_DF4iHKl
OV5640 camera the smallest tilting mount with an angle of 0-180° I was looking for a minimalist solution for the camera mount, but everything seemed massive and big, everything is beautiful, but it interferes with the printer's space.…
This is a simple remix of the cover from the original PanzerObserver2.4 camera mount. Check out the original design to see if it's what you need instead. I purchased this camera and it didn't need the extra hole that the original cover…
Remix for PanzerObserver ( https://github.com/Slidr666/VoronUsers/tree/18599db8c29c9a272f852d1dac9ad5d014d0a496/printer_mods/Slidr/PanzerObserver2.4 ) cover, to house a different model camera (…
Another Remix of PanzerObserver with a different OV5640 model (FF-160 Degrees) and no logo. Original credits and assembly con be found here:…
The original Creality K1 series camera is widely known for its unreliability and mediocre video quality. This model is a remix of the AngryCam camera mount that allows to install a much better third party camera, either IMX179 or OV5640,…
OV5640 I use https://nl.aliexpress.com/item/1005004373450096.html No supports needed. (Voron v0.1)
Remix for PanzerObserver https://github.com/Slidr666/VoronUsers/tree/18599db8c29c9a272f852d1dac9ad5d014d0a496/printer_mods/Slidr/PanzerObserver2.4 just the cover, to a different model camera. Can be bought from here:…
1515 Extrusion Mount for OV5640 5MP USB Cam Designed around the Micron+ (180x180x180) and to be mounted on the top rear extrusion to view the whole bed.…
For gantry mounted OV5640 Camera on Voron 2.4. It offsets the camera under the gantry so it won't be blocked by the X axis
A new faceplate to suit the OV5640 camera
About The axle of my cousin's playmobil broke, and a replacement part is no longer available. So I recreated the part from measurements of the original. The part is for the #5640 truck (see photos) Printing Use ABS or PETG Layer height…
The story is that I broke this part in some friends dishwasher when I was over for the weekend. Had the model been available back then, I would have stood a chance to print it and leave their place with a fixed dishwasher. Since I had to…
This make, holds the small camera on a pillar in place. It is a friction fit on the screws for the belt tensioners. This version has a 30° angle and fits for my needs. You can just put the camera on it and fix it with two zip ties. It…
A wrench for focus adjustment of LILYGO OV5640 camera See the original model for the camera holder.
Simple mount for an OV5640-type USB camera to fit on the front bar of a Micron+. May fit other printers with 1515 frame. Angle of camera and screw holes were chosen for my camera, but they seem to be fairly common across generic OV5640…
I needed a camera for my Voron Trident that would fit to the underside of the front rail due to the lighting ( Disco on a Stick ) being fitted to the inside of the top rail and not hit the toolhead. I wanted to make the camera adjustable…
These OV5640 camera modules are super cheap (under 10€) on AliExpress and are perfect as 3D printer cameras, so I designed a mount to put them on the inside of the Creality Printer Tent. Prints within a few minutes and without any…
I created a slightly taller foot for the Rowenta VU5640 fan. My vacuum robot was constanly driving onto the base of the fan. I printed it from TPU / flex. As I have two different versions of the Rowenta VU5640, I can tell you the both…
This is a camera mount for the Waveshare OV5640, adapted from Voxel3D_NL 's HappyCam. Motivation I preferred to put a chamber light strip on the inside edge of the 2020 extrusion, so I wanted the camera to mount beneath the extrusion…
Ive created this OV5640 camera holder for cheap AliExpress cameras to observe my prints remotely with Octoprint. Ive used the existing Creality Nebula holder for mounting the piece and added the HappyCam holder to hold the OV5640 PCB with…
Plant Cam: Square Press-Fit Socket for Autofocus OV5640 Plant Cam is a compact timelapse camera made exclusively for plants. I started this project with the goal of spotting problems early, understanding when to water, and monitoring my…
A small and simple 2020 extrusion mount for an OV5640 camera to be mounted just below the docks on the buffer crossbar. Uses (3) M2x6 self tapping screws to secure the camera to the mount. Two mount options are provided with a slight…
Modified main housing for PanzerObserver Micron Remix in order to allow fitment of Arducam OV5640 with heatsink. Mine unexpectedly came with heatsink and would not fit, but I thought it would actually not be a bad idea to use it anyways…
OV5640 camera the smallest tilting mount with an angle of 0-180° I was looking for a minimalist solution for the camera mount, but everything seemed massive and big, everything is beautiful, but it interferes with the printer's space.…
