Liczymy pasujące modele…
I took the cross section of DontWorryAboutIt 's Hill mount bearing and modified it to fit Ivan Urbánek 's Strurdy mount for Hadley telescope . To build it you will need a bowden PTFE tube (4mm diameter, less than 1 meter long), 12 M4x10mm…
The “Sunchronizer D2" Dual Axis Tracker is a solar module holder. With it “standard” 400W solar modules can automatically track the sun on the elevation and azimuth axis. The Sunchronizer D2 is the successor of the Sunchronizer D1 . With…
A fully 3D printed RC harbour tug with a working azimuth stern drive. The two pods rotate 360°, giving it the same rudderless maneuverability as a real ASD tug — spinning on the spot, crabbing sideways, and full thrust in any direction.…
The hinge i have used is not printed. I have made a printable version .
I created a version of AZIMUTH_AXLE_BOTTOM.STL for the Daveley Mount with 6 instead of 3 holes (for M5 inserts), so that it is easier to use different adapters for mounting on tripods without having to unscrew the whole mount every time.…
The AZIMUTH compass is made up of a 3D printed case and two dials engraved in transparent acrylic, the AZIMUTH compass, unlike other compasses, is equipped with a magnet and a compass rose as a needle. Its durable construction and…
This telescope mount has an integrated Azimuth rotation. The design is a remix of my prior remix ( Z-Brace - a stiffer Hill Mount for the Hadley Telescope ). It adds Azimuth rotation with only a few extra parts. The new mount design has…
The design auto-generates plots using a Python script based on the user's entered latitude. Other parameters of the sundial can also be modified; i.e. size of main dial, number of hours to display, start of January ring from center, ½ & ¼…
I designed an azimuth bearing for the Hadley telescope Hill mount based on a design by Pelf. The bearing uses a PTFE tube to reduce friction and the assembly holds together when moving the telescope. Bolt holes have been lined up to match…
This is an Azimuth bearing for the hadley telescope, if one is using a flat wooden/hdf/mdf base. The cupped part goes on the underside of the telescope board, and the part with the three nubs goes on the base. One can experiment by adding…
I took the cross section of DontWorryAboutIt 's Hill mount bearing and modified it to fit Ivan Urbánek 's Strurdy mount for Hadley telescope . To build it you will need a bowden PTFE tube (4mm diameter, less than 1 meter long), 12 M4x10mm…
Azimuth OD - The 3D Printable Overdrive Pedal Enclosure + DIY Electronics Kit This is the 3D-Printable enclosure for Azimuth OD , a DIY analogue overdrive pedal built for guitarists and makers alike. Get the PCB + electronic components…
54 degree wedge designed to slip into the pilar of Skywatcher AZ-GTI tripod. Requires no additional hardware this way and makes very sturdy design. Lock thumbscrews into shaft, and use original 3/8 thumbscrew to mount AZ-GTI onto wedge/…
An edit of c3n's azimuth bearing that is more in line with the visual language of the sturdy mount . The assembly process is very similar. However, to join the Upper Bearing pieces I used 3 heat set inserts in the female side in place of…
Equatorial wedge azimuth bracket Meade LX200 Classic 8inch
The controller for my heavy duty antenna rotator stopped working properly, but the rotator itself has a DC motor and is easily controlled manually with just a DC supply and an inexpensive PWM controller for speed ramp up/down. To…
The “Sunchronizer D2" Dual Axis Tracker is a solar module holder. With it “standard” 400W solar modules can automatically track the sun on the elevation and azimuth axis. The Sunchronizer D2 is the successor of the Sunchronizer D1 . With…
Useful for an azimuth bearing/slider using minimal PTFE tube. The flat head screws compress the PFTE tube to lock it in place. The PTFE fit is pretty tight as is, I found one corner to be very tight, likely due to a z-seam. Print one to…
A fully 3D printed RC harbour tug with a working azimuth stern drive. The two pods rotate 360°, giving it the same rudderless maneuverability as a real ASD tug — spinning on the spot, crabbing sideways, and full thrust in any direction.…
The hinge i have used is not printed. I have made a printable version .
I had a problem with the heat insert on the old design pulling out just because of how much force was being applied by the screw. So I modified it to be inserted without heat from the inside so it would always be held in tension by the…
(German below / Deutsch weiter unten) A problem with the iEXOS-100 mount by Explore Scientific is that one can’t really adjust the azimuth during polar alignment. However, there is already an M8 thread on the tripod, which was probably…
CHANGELOG: 07.12.22 uploaded stl/3mf revised Dovetail Female parts, changed to include thumb screws to lock down the scope in the dovetails and stiffen up the overall assembly. Big improvement. Left the original versions up. I am using an…
This is an upgraded knob attachment for the Azimuth adjustment screws on the Sky-Watcher EQM-35 Pro telescope mount. This should allow more torque and finer adjustment for polar alignment. Remixed from:…
The UN Logo without the wreath is basically the Azimuthal Projection (a.k.a. flat earth projection). Thought it would be a neat thing to print as a coaster. Meh.. But it's out here now in case you want to remix it. Like, to put it on top…
This is an addon to Rocker Frame Project . It allows precise control of azimuth of the telescope. By default the control is manual using the turning wheel. Optionally you can attach stepper motor and some control to drive it…
This is a replacement leg clamp for the "Heavy Duty Alt-Azimuth" tripod by Celestron (Item #: 93607). It turns out “heavy duty” was a bit of an over statement. I got one of these tripods from an auction site as an Amazon return to use as…
The EQ5 azimuth bolt knobs are hard to turn and hurt my fingers in the cold. I bought a pack of M6x50mm carriage bolts with nuts but couldn't find a bolt knob model that exactly fitted my needs, so I made my own. This bolt knob supports a…
I've been using these printed in PETG for the better part of a year without issue. Replacing the altitude lever-knob This is a drop in replacement. Start by removing the original lever and spring by unscrewing the internal screw. The…
This is my ‘grab and go’ mount and the little tray has always annoyed me. It barely holds four 1.25" eyepieces. So I spent about 30 minutes in Blender (it's a pretty simple model) and 5.5 hours printing to get a much larger tray with…
This is designed specifically for the Astronomers without Borders OneSky telescope . The ring gear is split into 3 pieces that fit very snugly, might require a touch of sanding. The snug fit and shaping around the upright means only one…
Changelog V4, 01-06-25: Reinforced the Top part where the Altitude adjustment screw lives, to reduce bending during loading. Adjusted dimensions on the barrel nut housing in the hope of reducing movements (housing is now closed on one end…
This is an azimuth bearing for the Hadley telescope that uses a PTFE bowden tube as a low friction interface material. Bowden tubes are inexpensive and readily available, making them an ideal source of PTFE material for the bearing. The…
