Liczymy pasujące modele…
Print settings Nozzle size ......................... 0.4 mm Layer height ....................... 0.2 Number of perimeters ... 2 (or more) Infill ...................................... 15% (or more) Supports .............................…
Protective box for my ASTF100 solar filter from Baader. It allows you to store the filter pre-assembled. The box has extra room to put in a pack of silica, which can be screwed close to avoid the silica bag banging around in the case. It…
I wanted to attach the ZWO EAF to the Baader Diamond Steeltrack 2" Focuser, and the bracket included with the ZWO EAF isn't really suited to the Baader. I've left a bit of play in the bolt holes, and the focuser brake hole should have…
This is simple adapter for new solar filter. I used Baader solar film I had home. Design is based on the original solar filter.
Print both pieces upside down. PETG or TPU is the preferred material as it flexes around the OTA.
I recently purchased a ToupTek AFW 5x2" filter wheel. Annoyingly my expensive Baader filters were too tall to fit into the filter wheel, as there is a little raised board at the bottom of the AFW with two sensors on which the filters were…
Holds a Baader MPCC by the external filter thread for fixed usage in a very low profile focuser UTA. Add three little wood slabs to the Backfocus setting tool so you have a handy driver to adjust backfocus, once. See the schematic to…
Disassembly tool for removing the sleeve nut on the battery insert, which is required in the event of problems with switching on the laser due to a loose connection. Suitable for flat-blade tool screw driver bit 5 mm with total length ~…
A laser collimator should be (perfectly) collimated at the factory. If this is not the case, it is (theoretically) possible to collimate it yourself. However, if this is not possible - as in my case, because I had no way of turning the…
If your refractor telescope has limited back focus, then this adaptor allows you to save up to 30mm compared with standard adaptors, and means you can achieve perfect focus. This also means you can easily swap over the ZWO ASI585MC (or…
Print settings Nozzle size ......................... 0.4 mm Layer height ....................... 0.2 Number of perimeters ... 2 (or more) Infill ...................................... 15% (or more) Supports .............................…
BAADER Diamond Steeltrack BDS-NT Base Adapter Adapter plate for a 150mm (6") Newtonian telescope to mount a Baader Diamond Steeltrack BDS-NT Focuser. The small hex nut adapters are provided for the inside of the tube. Fits on: GSO 150/600…
MTF [MagneTicFocuser] mount for BAADER Steeltrack focusers This is a mount to magnetically couple the MTF to the telescope. It fits on all Baader Steeltrack focusers. Link to the MagneTicFocuser [MTF]…
Three pieces are printed in TPU and one piece (adapter connection on the telescope side) is printed in PLA as it is being clamped in place. Category: Other
Baader UFC Dark-Slider This is a part for the astronomical filter UFC-System by Baader Planetarium. Suitable for all UFC systems Closes the aperture of UFC and telescopes at the same time to create darks with CMOS Cameras Vignettes the…
Baader UFC Seal This is a part for the astronomical filter UFC-System by Baader Planetarium. 3D-printed UFC seal to close UFC systems without inserted filter slides Suitable for all UFC systems - closes the opening for the filter sliding…
Baader UFC-Case for filter sliders This is a case for astronomical filters using the UFC-System by Baader Planetarium. UFC-Case for filter sliders with mounted filter Storage box with hinged lid holds all UFC filter sliders I fixed the…
The standard EAF metal bracket doesn't fit the Baader Planetarium Diamond Steeltrack 2" focuser without modifying the metal bracket to fit the larger M6 screws so I made up this bracket which utilises two of the M4 “attachment screws” and…
This holder is for 100mm baader solar filter (thin paper / film). Print a cover and an adapter of the size of your camera lens, and sandwich the filter film in. Then thread the adapter into the camera, make sure it's secure. And you're…
altura de capa 0.28 - 0.32 con boquilla 0.4, hecho en PLA Puedes ver más diseños míos en: https://cults3d.com/es/usuarios/Didymoon/modelos-3d
Two of the “160mmBaaderERF HolderV1” files fit together as a clamshell around the Badder 160mm ERF. Clear aperture is 153mm. Printing was done with PETG. Use 1mm felt tape along the edges and front/back to hold the ERF securely in place…
Print the filter holder 2 times. Sandwich the filter between the 2 filter holders and glue them together. I used E6000 glue. Stay safe and only purchase certified filters. Compatible with the Hadley telescope:…
The Canon EOS-M series digital cameras, especially the EOS M6 Mark II with it's mirrorless design and 32.5MP ASP-C sensor, is a great camera to get for astrophotography if your not looking for a dedicated astrophotography camera or full…
Protective box for my ASTF100 solar filter from Baader. It allows you to store the filter pre-assembled. The box has extra room to put in a pack of silica, which can be screwed close to avoid the silica bag banging around in the case. It…
These two parts just fit between the OTA tube and the Steeltrack plate. They eliminate any chance of stray light and pack the space maybe aiding rigidity and squareness. Just loosen the plate and push these parts in on each side then…
Baader delivers a 3D tool for the PAN clambs and stronghold: https://www.baader-planetarium.com/de/3d-gedruckter-ringschl%C3%BCssel-f%C3%BCr-baader-pan-eq-klemmen.html I created a version with fusion 360 which can stay permanentaly on the…
