Liczymy pasujące modele…
Instead of using a 8mm rod & bearings in the X-ends, the X-ends have been changed to make use of a single LMUW10 (and thus 10mm rods). No loss of print volume, no custom firmware, it's all fully compatible parts. Oh. And it's usually…
I was always kind of upset with how heavy the stock MK3S+ and Bear toolheads were, so I decided to modify a friend's Orbiter mount to work with the amazing Annex Engineering Sherpa Mini extruder (link to github below). Prints have been…
Remix of two wonderful designs to allow for you to fully rigid mount a TriangleLab or Phaetus Dragon SF/HF and also use the Delta P V2-R2 fan duct on the BearEXXA. Any and all feedback is welcome! NOTE: You will need 4 M2.5x5 or 6mm SHCS…
Disclaimer: it's a really minor modification, but this is untested . I haven't put this to use myself (I went straight to a 10mm Z-axis in my upgrade/mod-endeavors). Instead of using two LM8UU bearings in the X-ends, the X-ends have been…
I was always kind of upset with how heavy the stock MK3S+ and Bear toolheads were, so I decided to modify a friend's Orbiter mount to work with the amazing Annex Engineering Sherpa Micro extruder (link to github/BOM below). The stock Bear…
I was not content with other extruder designs for Slice Engineering Mosquito hotend so I designed my own. Introducing the BearExxa Mosquito based off of the Bear Extruder created by Grégoire Saunier . Big thanks to both Grégoire Saunier…
This has been made for use with common 20T 5mm-bore idlers with the following dimensions: 5mm bore 18mm flange 9mm width (6mm belt) Changes made to the original the parts: Upsized the bore to 5.04mm, same as the E3D-idler design (from…
This remix of Gregsaun's BearExxa (Bear extruder and X axis) repositions the extruder to match the vertical position of the stock MK3S extruder. This allows for stock firmware to be used without flashing any calibration firmware. The…
- Added some space for cheap couplers (Motor Mounts) - Added some Bearing to Top mount - Reduced Guiding in Slot Added remixes guide for Rod from https://www.thingiverse.com/thing:3282965
Oops Well, I was browsing the repo after I published this and saw there was already an official reverse bowden setup up there. https://github.com/gregsaun/bear_extruder_and_x_axis/tree/master/optional_parts/reverse_bowden I'm leaving mine…
Revo Six needs ptfe tube trimming. This tools is used to trip it. Print parameters are the ones used for original tool
Modified the Bear Upgrade 2.1 Extruder (BearExxa) Cover (fs-cover) to fit the original M5 fitting used by Prusa for the MMU2 cover. I bought the fittings here: http://lecktor.com/en/nuts/159-tappex-microbarb-m5-pack-of-10.html Print…
This re-adds the collet from the Dragon hot end back to the mounting hardware. This should help keep the PTFE tube nice and flush against the top the hot end and prevent it from pulling out when removing filament. The collet isn't too…
Bear Extruder Motor and Idler part for Chinese TR8 Anti Backlash. Model is for MK3s 1st Version to test. Category: 3D Printer Parts
This Extruder Cover uses the cavity at the base of the Revo 6 to prevent the hotend from spinning, and also prevents heat from the heater core from escaping into the cooling area. For bearexxa V1, and also a version for the delta p bear…
While using the original model for a few hours of printing, I noticed that the PTFE tube slowly moves upwards because of the retractions and inevitably gets caught by the extruder wheels. The tube is afterwards damaged in such a way that…
You will need an additional 625RS or 625ZZ bearing. It is not possible at the moment to add mor things to the remix sources, so i have to link them here manually. This thing is a remix or inspired by the following things:…
This version of the X carriage changes belt alignment to make it compatible with BearEXXA. It allows to use the original MK3S toolhead on a printer with BearEXXA X axis mounts
Changed the filament sensor cover so that an LED behind it shows the status of the sensor. The side walls of the recess are slightly bent to avoid pushing through. There are two versions of the window insert available. The smaller one fit…
I wanted to be able to use my cheapo v6 hotend for one hand nozzle swap, but the screw heads were colliding and the PTFE was not secured. Currently testing, use at your own discretion I bear no responsibility! Credits to Greg Saunier for…
A mashup model to add a PC4-M10 ptfe to the bearexxa extruder
Simple mod of BearExxa filament sensor cover to accept QSM-M5 fitting when printer is placed in an Original Prusa Enclosure.
