Wyniki wyszukiwania: chuck

adapter for engine with gear, for dremel chuck

in case you don't have a gear, cut the STL and adapt the tip of your motor.

Drill Chuck Handle

I am looking for a practical and innovative solution for my Wolfcraft drill chuck ease to use with hand in vaious DIY projects. This unique 3D model handle is specifically designed to be easy and confortable. U can use any material and…

Carvera Chuck Subplate

This places the center of the chuck in the anchor 2 (0, 0) position. Print the subplate on an angle (30 degrees is ideal) to given it higher shearing strength, and be careful when installing the chuck to not over do tightening it. The…

gridfinity 1x2 bin dremel tools, spanner, chuck and std. dremel 3.15mm (1/8") tools

Gridfinity bin for Dremel It has a 1x2 bin footprint. Used for Dremel spanner, chucks and standard 3.15mm (1/8") tools. I really needed a bin with both spanner and tools, and figured I'm not alone. There's no lip on the bin since You…

M14x1 bolt for Three Jaw Chuck

This is the bolt to thread into the Three Jaw Chuck and connect to your drill. https://www.printables.com/model/133491-25inch-three-jaw-chuck I epoxy an M6 bolt and drilled through the 2mm hole and inserted a nail to bond the two pieces.

Carvera Upright Chuck Subplate

Joe N style alignment, where instead of pins it uses the anchor, makes it much easier to cutout. Just make sure to apply pressure towards the anchor2 corner while screwing it down. The bolt needs a M14x1.00 thread to secure the chuck from…

Lathe 3-Jaw Chuck Spider / Stop - set of 6

A set of lathe spiders for lathe chucks with jaws up to 20mm wide. The chuck I made these for is a 160mm. I created a parametric model in Fusion so any depth or jaw width can be added if requested. Alternatively changes in depth can be…

Chuck Chucks – Cute Martial Arts Chicken STL (FDM & Resin Ready)

🐔 Chuck Chucks is here. Round. Feathery. Slightly unhinged. This printable cartoon chicken comes armed with nunchucks and a whole lot of poultry-powered attitude. Whether you print him in resin or FDM, as a single-colour beast or a…

Movie Maniacs | Chucky

Overview "Hi, I'm Chucky, and I'm your friend till the end…Wanna play??" The classic Good Guys doll brought to life through your printer. This figure stands about 100mm tall and is split up into parts to accommodate a 4 color multicolor…

Nin chuck filit

cool to carye arond

Vevor YS-2260A / MX-600 Chuck Chip Cover

Works with 3-yaw chuck that comes originally with Vevor YS-2260A / MX-600 / MX-400 and similar models. Like my design? A lot of work goes into every 3D model I publish for free download. If you would like to appreciate my efforts just buy…

Nunchucks of Lightning

Wii Nunchuck Tape Dispenser

Summary Wii would like to present the latest revolution in bizarre Video Game merchandising, the Wii Nunchuck Tape dispenser (pls dont sue me Nintendo). This print comes in 2 parts, the main nunchuck, and the roller section. It is a part…

DIY Tailstock Lathe Chuck Spindle Chuck 3D Printer

All Lathe DIY Machine https://3d4diy.com/category/diy-lathe 3D Printer Machine DIY: https://3d4diy.com/category/diy-3d-printer All mini CNC Machine Homemade https://3d4diy.com/category/mini-cnc All Milling CNC Machine Homemade…

Avatar DIY Lathe Spindle Chuck 3D Printer

All Lathe DIY Machine https://3d4diy.com/category/diy-lathe 3D Printer Machine DIY: https://3d4diy.com/category/diy-3d-printer All mini CNC Machine Homemade https://3d4diy.com/category/mini-cnc All Milling CNC Machine Homemade…

Chuck It Dog Ball Holder

After getting tired of having no way to keep the Chuck It balls from my dog when not in use, I whipped this up. It's been very useful. I'd use 3 or 4 walls and very light infill...maybe 10%. Any material will work. PLA is fine.

Pineapple Guy MADE BY @Chuck_Chubbs

very fun to make made it just for fun

Avatar Spindle Chuck Lathe Milling CNC DIY

All Lathe DIY Machine https://3d4diy.com/category/diy-lathe 3D Printer Machine DIY: https://3d4diy.com/category/diy-3d-printer All mini CNC Machine Homemade https://3d4diy.com/category/mini-cnc All Milling CNC Machine Homemade…

Avatar Spindle Chuck Lathe Milling CNC DIY

All Lathe DIY Machine https://3d4diy.com/category/diy-lathe 3D Printer Machine DIY: https://3d4diy.com/category/diy-3d-printer All mini CNC Machine Homemade https://3d4diy.com/category/mini-cnc All Milling CNC Machine Homemade…

Avatar Spindle Chuck Lathe Milling CNC DIY

All Lathe DIY Machine https://3d4diy.com/category/diy-lathe 3D Printer Machine DIY: https://3d4diy.com/category/diy-3d-printer All mini CNC Machine Homemade https://3d4diy.com/category/mini-cnc All Milling CNC Machine Homemade…

Chuck Norris

Chuck Norris

Parametric dowel chuck

This is a rather specialized jig, but maybe someone else can get some use out of it. It's designed to fit into a hole drilled with a hole saw or similar tool, and secure a wooden dowel, metal rod or pipe, or similar smooth, cylindrical…

Chuck Norris BobbleHead

Chuck Norris BobbleHead use a spring which is 38mm tall. and 8mm wide or 5.5mm wide

2.5inch Three Jaw Chuck with 5mm shaft mount

Chuck which can be slid onto a shart of a nema17 motor and locked on with an M4 screw.

MT2 / MK2 / Morse taper 2 / Chuck Key Tool Holder for lathe WM210

Размеры посадочного места на картинках. Печатал АБС пластиком, заполнение 15 процентов. Можно печатать и другим пластиком, усадки будет меньше, просто садится будет плотнее Подходит для Токарного станка WM210, закручивается винтом для…

Combination Chuck Vise and Lock Pinning Tray

I was looking for a good vice and pinning tray as I go deeper into locksport. My printer is too small to make the the regular vise base but big enough to make the small base. To limit any possible instability, I was going to expand the…

Storage box for quick-release chuck “Multifix” size "Ab"

I created a little storage box for the quick release chuck named "Multifix" in size "Ab" by Paulimot. https://www.paulimot.de/drehen/schnellwechsel-stahlhalter/ab It can be connected to each other to get a better stand for all quick…

Gridfinity chuck holder for MT3 chucks

I printed this in PLA+.. Tip: Check the dimensions in your slicers measuring tool before printing to make sure you will get what you expect.

simple blocky nunchucks

there are a few instructions for it to work properly: a nozzle >0.5 mm supports touching build plate scale to around 4x or more must be sliced

Basic nunchucks

Basic nunchucks that i made in onshape how to assemble (v2) only print the two models v2 part one and part two screw them together until snug now you have some nunchucks!!! (note v2 is made in favor of a smaller print area, that is why it…

Schrader Valve chuck key

Key for loosening/tightening a schrader valve cap.

screwdriver shaft for lathe chuck

addon for the lathe chuck

Air chuck coupler cap

Fits 7/8in or 22mm diameter air chuck quick disconnects. keeps debris out, nice snug fit in TPU

Wood Lathe Chuck Wall Mount

Designed for the Oneway Stronghold chuck. Prints in two parts and connected with an M5 35mm screw and nut. I printed it in PETG. The tool holder is angled by 3 degrees so that the chuck stays on the wall.

Huge Dog Chuck Ball With M3 Screws

The original model is perfect. I just didnt have M5 screws, so resized the holes and slots for the nuts for M3 insteadd.

Mini Fidget Nunchucks, Palm-sized Decompression Toy

## Design Concept The palm nunchucks are designed for stress relief and casual fidgeting. The compact size allows for easy handling and is suitable for quick routines while multitasking or relaxing. ## Uses This fidget toy is perfect for…

creality falcon laser chuck mount

creality falcon laser chuck mount

Sklíčidlo - 3D PRINT CHUCK KIT CARD

Pro zákazníky, příznivce a kamarády firmy PROFIKA s.r.o., jsme připravili 3D tištěnou, funkční hračku sklíčidla. Zde je Video pro složení: Návod ke složení i jako obrázek zde najdete taky:) Hezké skládání přeje Melloun:)

Good Guy Chucky doll Funko pop

Chucky doll as funko pop in the photo a proposal for painting the figurine

Lathe chuck stop

The chuck stop was made for my Hare & Forbes AL-320G / L141 metal lathe (Model available within Australia) to locate shorter parts beyond the chuck jaws to provide clearance for facing operations. It has been designed for the standard…

Thumb-Chucks 2.0

UPDATE 7/9/23: After posting this on Reddit, I received some feedback suggesting that I add a bearing to this model and I've done just that. I'm leaving the original version and adding .STL and .STEP files for the bearing version,…

Cordless drill holder (for 43 mm drill chuck like Makita, Bosch, DeWalt, Einhell, Ryobi, Black&Decker, Worx, Scheppach...)

A sturdy cordless drill holder for almost all cordless drills (Makita, Bosch, Einhell, DeWalt, Ryobi, Black&Decker, Worx, Scheppach and many more). This holder will take any drill chuck with 43 mm outer diameter and a maximum length of 70…

Custom 53 mm spreader jaws for the Record Power SC1 mini chuck

I made these 53 mm external jaws to fit bowls I made with the Nova chuck with standard jaws on the SC1 so I could finish or post-work the bottoms of bowls more easily. The SC1 is so small (51 mm diameter) it is not in the way when…

Dremel chucks adapter holder

I made this box, because the chucks adapters are always nowhere to find. The shaft is 4mm. Under each hole is the number of the chuck. 0,5 - 0,8 - 1,0 - 1,2 - 1,5 - 1,8 - 2,0 - 2,4 - 3,0 - 3,2 I have to print it once again, i did not…

LeChuck's brewery

LeChuck's brewery - traditionally crafted grog you can print it as a coaster or you can add your own inserts for magnets and stick it on your fridge! for true pirates and fans of Monkey Island and grog

Sherline ER-16 3-Jaw Chuck and Tommy Bar Storage - Gridfinity 2x3

This is an addition to the Gridfinity storage system designed by Zach Freedman of Voidstar Labs who “stole” it from Alexandre Chappel. I made this storage for the Sherline ER-16 3-Jaw Chuck and Tommy Bars. It uses a 2x3 area of the grid.…

Lathe 80mm chuck external jaws

Printable jaws for 80mm lathe chuck

Parametric xTool RA2 Rotary (Magnetic and Non-Magnetic) Chuck Jaws and Pegs

Motivation The xTool RA2 rotary is a great accessory, but the included chuck jaws have a few shortcomings: Workpieces with shallow stepped inside geometry (lip) are difficult to get a good and even grip especially when tapered Outside…

Mini Chuck 1/4" (6.35mm) long-shank quick-connect handle

This will snugly fit this 0.3-8mm keyless drill chuck on Aliexpress . If you find it is a tight fit you could either print slightly larger or lightly run a file/sandpaper over the faces on the shaft of the chuck. Modifications from the…

adapter for engine with gear, for dremel chuck

in case you don't have a gear, cut the STL and adapt the tip of your motor.

Wood Lathe - Sphere Chuck 100mm

02.01.25: Inch threads are added.

Wood Lathe - Sphere Chuck 60mm

02.01.25: Inch threads are added.

Wood Lathe - Sphere Chuck 150mm

02.01.25: Inch threads are now added

Lathe chuck key holder

Holder for a key of a 100mm chuck

Wood Lathe - Chuck Flange 80mm

Distance front bores M5 = 60mm Distance back bores 5mm = 30mm and 40mm Avaiable threads: M33x3,5 M14x1 M14x2 (for angle grinder disks) The 30mm back bore version is suitable to this one:…

Wood Lathe - Self-Centering Dome Chuck

Total length 262mm, so can also be used on tabletop wood lathes. It's possible to add a small chuck or an indexing attachment or a worm gear. Mechanical parts like ballbearings are just added for the measurements. 18.09.24: Missing…

Nun-Chucks

This is a model of nun chucks. The chain is pretty strong but will break with a lot of stress. Supports: On

Haltec H-5265 air chuck dust cap

Dust cap for Haltec H-5265 tire valve quick connect air chucks. While airing up and down 4 tires at once, the caps reduce the risk of getting sand in the chuck locking mechanism. Rear part prevents sand to get in from the back, use…

Zap Rowsdower - The Canadian Chuck Norris, license plate frame, MST3K

Zap Rowsdower - The Canadian Chuck Norris, license plate frame, Mystery Science Theater 3000 R.I.P. Bruce J. Mitchell Print Settings Printer Brand: Creality Printer: CR-10S Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 25…

chuck e cheese caution wet floor sign

original chuck echeese late 80's caution wet floor

Positioning Fixture for Chuck Backplate

Fixture for milling flats on a backplate for a k11-100 chuck. Jig helps to position the backplate in the vise at to the corrrect angle. 2 x 2 flats are needed to hold the chuck in the vise or to mount it on a rotary table.

Chucky hueforge

Chucky hueforge 4 colors Hauteur de couche 0.08 layers 0 à 1.72 noire (black) layers 1.72 à 1.88 bleu (blue) layers 1.88 à 2.84 orange layers 2.84 à 3.08 blanc (white)

Pick Puck Chuck

For use with https://www.thingiverse.com/thing:6387759/files. Includes 2.5mm allen key holder, screw driver holder, pick holders, misc tray, and pinning tray. Untested. Credit to https://www.thingiverse.com/lockchuck/designs for original…

LaserPecker 1 mount for Jacob's Chuck: drill press, lathe tailstock, etc.

Mount to stabilize the galvo-style LaserPecker 1 on a drill press Jacob's chuck. Easier to manage focal distance and avoid bumping the lightweight tripod it ships with. Optional “flex pad” model can be printed in TPU or another material…

chucky halloween funko

Escalalo al gusto

80mm 3 Jaw Chuck Holder

A neat way to store all the bits for the Chinese 80mm 3 jaw chucks - especially when you use multiple chucks on your lathe each with their own accessories. The lid has multi part components for the text for those that have MMU printers.…

Atomstack Maker R1 Multi-function Chuck Rotary Internal Tumbler Clamping Jaws

These attachments are designed to clamp the tumblers from the inside of the mouth. This allows you unobstructed access to fully engrave/etch the entire outside of the tumbler without the jaws interfering with the laser head. There is a…

Nunchucks

Nunchucks for event costumes like Halloween. For stronger chains and handles use a higher infill density. I used a 50% and my print is strong enough to smash cardboard boxes without taking damage. Model starts off large. Change sizing to…

Tactical Brew Holder (Chuck Norris Version)

The TacBrew tactical beer can holder (NSN 7360-01-487-3159) allows you to mount your brewski to your pew pew. It comes complete with the non-patented Brewski Retention Knob System to keep your cold one firmly in place when doing some…

Drill Chuck Handle

I am looking for a practical and innovative solution for my Wolfcraft drill chuck ease to use with hand in vaious DIY projects. This unique 3D model handle is specifically designed to be easy and confortable. U can use any material and…

1/2 inch Keyless Drill Chuck with R8 adapter caddy

Keyless drill chuck with JT33 to R8 adapter taper affixed.

1/2 inch Keyless Drill Chuck with R8 Caddy

½ inch Keyless drill chuck caddy with R8

Wii Nunchuck USB-C Adapter Case

Case for a QT Py RP2040 and a Wii Nunchuck adapter breakout. The QT Py snap fits into the bottom of the case, and 2 M2.5 screws and nuts are used to mount the Nunchuck adapter into place. A 50mm Stemma QT cable us used to connect the QT…

Gridfinity MT2 - JT33 Jacobs Drill Chuck Holder

Gridfinity with magnets, holder for jacobs chuck JT33, with chuck key

Gridfinity 3-Jaw 100mm Lathe Chuck Holder

gridfinity with magnets, holder for 10mm lathe chuck with studs, and chuck key.

Gridfinity 4-Jaw 100mm Lathe Chuck Holder

Gridfinity with magnets, 4-jaw lathe chuck with studs holder and place for chuck key

Gridfinity ER32 Collet 100mm Lathe Chuck Holder

Gridfinity with magnets, lathe chuck holder for ER32 chuck, and two standard sized collet nuts

Gridfinity Lathe 3-Jaw 100mm Chuck Jaws Holders

3-jaw chuck holders for inside, outside and blank jaws along with matching screws

lathe chuck

made for a genera purpose multi function tool to hold whatever part you need it to.

Carvera Chuck Subplate

This places the center of the chuck in the anchor 2 (0, 0) position. Print the subplate on an angle (30 degrees is ideal) to given it higher shearing strength, and be careful when installing the chuck to not over do tightening it. The…

Chucks for KW spin coaters

These designs are a series of chucks for KW spin coaters. Three of them are adapted for silicon fragments of different sizes. They use O-rings of different sizes. The size is indicated in the file name with the first dimension being the…

Drill chuck key grip handle 6mm 1/4" shaft

Drill chuck keys are always really painful to use because their handle are so small. This gives you more material to grip on to, which makes it more comfortable to crank down or loosen the chucks on your drills. Fits most 6mm(¼") shaft…

Drill chuck key holder

Holder for C3/S3 chuck key using round 12mm magnets of 3mm thick

W25 spindle soft jaw chuck

I made this to hold delicate parts on the lathe. I print everything at 100% and then turn the inside to the correct size. the ring on the outside compresses the inner portion to hold the parts. I used PLA although I would suggest…

Nunchuck para XBox (Nunchuck for XBox)

Español: Este diseño está pensado para poder fabricar de forma muy económica un mando que conectado al Adaptive Controller de Microsoft, permita realizar las funciones del joystick izquierdo o derecho, así como las funciones de los…

Chuck Spannfutter

Use holding drill bit (∅ 3mm and ∅ 2.35mm) e.g. use grinding drill bits manually as a skewer grip holding e.g. PTFE tube (∅ 4mm) to push/pull through holes Print no support needed low layer <.1 PETg eventual brim or raft

Mini chuck

Mini chuck to be added to a electric drill. 3 independent clamping jaws, can clamp both inside and outside diameter. Design source available here in onshape:…

Woodchuck pencil sharpener 2.0

Add some joy to your workbench! Great for all woodchuckers (woodworkers) out there! Store your pencils, if they are dull sharpen them! Pencil sharpener-…

Jaws for Lathe chuck 80mm

Jaws originaly being used for mini-lathe MN80. I'll be happy if anyone try it on different turning heads. It is for 80mm diameter. Let me know I update description. Print Settings Rafts: No Supports: No **Resolution:** 0.1layer 0.4nozzle…

Vacuum chuck interface rings

These are designed to slip over PVC tubing when making vacuum chucks. The Fusion360 file is provided and it is parametric, so changing the centerdiameter will modify the overall size. 3MF contains various common sizes.

Xtool Tumbler Chuck Adapter Lid

I printed in PLA with 100% infill so I can tighten the chuck really well.

Three-Jaw Chuck for Highly Adjustable Ball Vice System

I like the model 'round vice - 3 point clamp' of @93djen very much, but I liked to use it with mine ‘Highly Adjustable Ball Vise System’ https://www.printables.com/model/1109371-highly-adjustable-ball-vise-system . Since the original…

Chucky 2 good guys head

Scan of the screen used original head

Base plate to mount Chuck vise to ball vise

This is a base plate to mount Sneaks's Bench Mountable Vice directly to Chris Borge's Open Ball. It needs to be printed with supports, and then slides into the dovetail of the ball vice. Update: I updated the model with version 2, which…

Spacer for 3-Jaw-Chuck

for 3-jaw-chuck diameter 125 mm jaw width 16 mm jaw height 19mm different spacers for 2, 5 and 10 mm clamping depth

Medieval Chucky

A Medieval Chucky. You can support me on https://www.patreon.com/Schlossbauer if you like my work. Category: Toys & Games

Drill chuck holder handle

Description I designed this handle to fit this specific 0.8-10mm chuck from Aliexpress ( https://www.aliexpress.com/item/1005006997808237.html ), using the hex adapter. It is very handy for cleaning up holes in prints, or drilling soft…

Truck Tire wedge /chuck- scale models for diorama 1/14, 1/16 ,1/12,1/10

Printed at 100% fits 1/16 scale or resize in your slicer to fit desired scale.

Mount for Proxxon Micromot chuck holder

My Proxxon Mixromot came with some spare chucks which i had no right spot for. This model allows you to simply screw it to a wall (or anything else ^^). It is designed as a tight fit. You should still be able to pull it out while mounted.

gridfinity 1x2 bin dremel tools, spanner, chuck and std. dremel 3.15mm (1/8") tools

Gridfinity bin for Dremel It has a 1x2 bin footprint. Used for Dremel spanner, chucks and standard 3.15mm (1/8") tools. I really needed a bin with both spanner and tools, and figured I'm not alone. There's no lip on the bin since You…