Liczymy pasujące modele…
A bolt-on quick-release mount for the Cygolite Dash bike light to replace the stock rubber strap that would not keep the light in place. Trail approved! One-handed quick-release! Minimal footprint! Easy installation without removing…
This is a remix of this thing made specifically for the Cygolite Hotshot Pro bike light. There are two files available for download: .scad file : This is the OpenSCAD model you can use to further customize this thing. Do this in OpenSCAD…
This is a replacement top clip for a Cygolite Metro handlebar bracket. The plastic on my original clip broke so I designed and printed this replacement part. Note that this is only the top section. It does not include the clamp that…
ORIGINAL MODEL FAILURE MODE: Firstly, BIG THANKS to @SeanK_97580 for the original model! After a year-plus of good service holding my Cygolite Metro in place on my daily commute, the light mount failed at the clip + screw hole interface .…
Stripped jmisavage's design for use with a simple L-bracket instead of having extra holes. I had to do a lot of post-processing with a file to get it to fit. Probably my own setup's fault. Kind of difficult to release the light, but…
I have a saddle bag that i carry with me during long mountain bike rides. I want the saddle bag to stay mounted as close and snug to the saddle and seatpost. During long rides, the end of the saddle bag that attaches to the seatpost…
Zip ties hold this mount to the rails of your saddle while your Cygolite Hotrod, or similar, straps around the descending mounting position. A bump around the base retains the light incase of bumps shaking the light down. This is made for…
I wanted to clean up my bike cockpit so I created an adapter to connect a CygoliteMetro bike light using a GoPro type mount. Given that the light weight and vibrations that mostly happen on the vertical direction I would suggest to print…
Mount for Cygolite Hotshot bike tailight on an Axiom Streamliner family of racks. The model is designed for M4 mounting hardware. I printed this using Prusament Galaxy Black PETG. Printed with bed supports only, using 3 perimeters and 15%…
This is a holder for the Cygolite Hotshot Pro bicycle lamps. The mounts from Cygolite are designed to attach to the seat post, but may be obstructed when a rear rack is used. This design uses and M6 screw and nut to hold the mount (and…
This bike light mount adapter is for the Ergon Saddle that comes with the Topeak quick clip. https://www.ergonbike.com/en/product-details.html?a=saettel&anr=44001402&s=smmtb there are 3 files: MODEL A is a sleek design with 10mm down…
This bracket enables you to mount a rear blinky on a Blackburn EX-1 or EX-2 bike cargo rack. Zip ties are sufficient but I recommend using glue (E6000) also. I have tested it on the NiteRider Solas and the CygoLite Hotshot
I lost the mounts for our Cygolite Metro 1100 & older Cygolite Metro 500 lights for family bikes. This fits the 22mm bar on Cannondale Quick CX3, Cannondale Quick 20, Cannondale Quick 24, & likely other models. The standard part fits the…
This is a replacement cover/seal for the USB port on the Cygolite Metro bike light. It's not as watertight as the original, but it's better than nothing for keeping dust, water, and debris out of the case. Printed in Ninjatek Semiflex. It…
I made this riser that fit my handlebar better and rise the light over my handlebar bag as well. It used two captive m3 nut as well as m3 button screws. onshape cad file :…
A 1x1x4 Gridfinity bin that holds a Cygolite Metro 800 headlight face-down so the charging port is accessible. This is part of a series of Gridfinity bins intended to act as a customizable cycling accessory charging station. Other bins…
This is an articulating bracket to attach a Cygolite HotShot PRO to a bicycle / trike 6mm safety-flag pole. I use 2 (M3 x12mm screws w/nuts) and 1 (M5 x 20mm w/nut) I printed in PETG with supports at 70 degrees and only in the M5 fastener…
This is a basic taillight mount for off-the-shelf Cygolite models frequently used by commuters and bikepackers. After 6 months of testing on several bikes, I am only using the low-profile sideways configuration. This keeps the top of the…
I didn't want to add an additional handlebar mount for my phone when I have my bike on the indoor trainer, and I already had a Cygolite mount for my bike light. The ball socket version is compatible with 15mm balls commonly found on…
