Liczymy pasujące modele…
A printable knockoff of a sealant dipstick. Orange Seal used to make these, but don't appear to be on their website anymore. For use with bicycle tubeless systems to check how much sealant is still in the tire without having to dismount…
To connect the engine dehydrator to my Lycoming O-360 in a smooth way, I designed this simple adapter plug. The thread is a standard 1 1/8-12 UNF and the hole is dia 8 mm to provide a snug fit for a 6 mm plastic tube. It's tight enough as…
I printed it on ordinary cr6 se with standard PLA. I have used 0.16 layer for better resolution of marks and numbers.
Uses an m3 nut and m3x12 screw to bolt a handle onto the nub leftover on your broken dipstick. You will need to drill a hole in your dipstick to attach it. Print it on its side (close to the orientation it comes in) with a little bit of…
Replacement cap for the oil filler of the motor. Made for an Eberth 5.5HP motor but may fit on other types of motors. ¾ in ANSI thread Printed on a Creality Ender 3 S1 using black PLA 1.7mm filament. I recommend to print in vertical…
This is a Oil Dipstick for the EJ20 Subaru Engine ( http://www.thingiverse.com/thing:2451310 ). Print instructions Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.15mm Infill: 100% Filament: Geeetech PLA Black…
Print laying down, some support is needed due to orientation. Use temp resistant material I used petg but i would suggest asa or abs. So far it held up. This was for a 2010 model check if others will use the same.
Plug to block off the dipstick tube hole in most GM transmissions. Must use with existing dipstick grommet.
Your Ariens snowblower has an auger gearbox. It has oil in it. Have you ever checked the oil level? Now you can. Just remove the filler bolt, dip and read. The level should fall within the notch on the dipstick. Add oil as necessary. Read…
I printed this out of PLA and when I checked after a drive it became super flimsy. Don't use PLA. I printed it in PETG in October of 2024 and I'm still driving on that sucker (Feb 2025). Fits nice. I was fortunate enough to recover the…
Transmission dipstick on my Dodge Van keeps falling off so I tried designing lock tab to hold it in place. Fits on ¾" diameter dipstick tube Mopar 904/727 transmissions. 2 piece design - glue together. Consider printing in high temp…
I wanted to get it modeled and posted, just in case somebody lost theirs. Not sure what materials would be best for engine temperatures. A piece of steel or brass could be used to replicate the stick and the handle could possibly be made…
Print 2 pieces for assembly Allows the use of thinner old style m50 dipstick on a M54 style sump. Printed mine in PLA and smeared RTV on the outside lip. Use original o-rings Has held up fine so far for me but your mileage may vary.
Peilstab, Dipstick Wiesel / Berlin / Troll 1 12 Liter
Der Motoröl-Meßstab an meiner Harley war abgebrochen. Da das Originalteil sehr teuer ist, habe ich mir selbst einen neuen Peilstab gedruckt. Er paßt an Twin Cam 88. The engine oil dipstick on my Harley was broken, so i printed a new one.…
Dip stick for a 1982 Yamaha XJ1100 motorcycle for middle and rear units. I believe it fits the XS 1100s too. Based on measurements I found online because I didn't have an original. I don't remember where I looked up the dimensions. Use…
This is my latest revision of my dipstick tube adapter. I made this for my 2003 Honda Pilot. There are two ways to fill the transmission, either through the dipstick or through the port where a cooling jet is installed. Accessing the port…
This is a replacement for the plastic head of an Oil Dipstick for a Kanzaki KM3P Gearbox. This gearbox can often be found on YANMAR 3GM30 marine engines.
Since this dipstick is easily breakable(and mine broke) I modeled it! Modeled using SolidWorks. Used photoshop for known dimensions and calculating rest. Found some of the dimensions in a Russian forum:…
This is to help in refilling the transmission on a 1st gen Honda Pilot Transmission through the dipstick. This may work with other similar V6 Hondas of this era. I can confirm this works with a 2003 Pilot but can't say it will with…
Most of us have filled rear differentials until the oil starts to come out, but GM specs shows a specific 4 mm range level and the OCD mechanic in me figured why not make a dip stick with those specs! This worked for my 2006 Chevy 2500HD…
This Tool will allow you to drill out a later Mustang or other Rear-Sump 2.3L Lima engine for the Front-Sump Dipstick Tube used on Mustang II, Pinto, Bobcat, and other models. You will need a 5/16" and 23//64" Drill bit in order to…
Oil dipstick for car It is best to make it from materials that are resistant to high temperatures. ABS is suitable for
I needed to measure 4 inches of headspace in 55-gallon drums at work. This is a simple dipstick that has ¼ spaced ribs for measuring the headspace through the bunghole on the top edge of the 55-gallon drum. Simple model, made with the…
On my 2011 Jeep Grand Cherokee, there is a knob/plug that you have to remove to check the transmission fluid level, using a aftermarket dipstick. It is very small, and very tight to remove, especially if it hasn't been removed in a while.…
Over time, the plastic of these dipsticks swell up or something 'cause they become impossible to turn without pliers. Well, I lost my pliers…
This is a dipstick for a Yardman MTD model 11A-B02J701. The part number is 951-14440. Use PETG. I printed it at .3mm and 5% infill. I included just the cap if you can't get the printer to print the tall dipstick. Print Settings Printer:…
I don't like the screw-in version of my Triumph, so I made a stick-in one. And in white it's much better to see the oil on it. The length of the original depends a bit because of the o-ring, but I'm sure the printed one is well within…
dipsticks for your eg. a pot (25cm) or bucket 5gal version - customizable for fl. oz. or cup/pint/quart
