Liczymy pasujące modele…
I wanted something to protect my Cardputer when I carry it in my jacket pocket. Buttons, power switch and SD card are all accessible on the back without removing the device from the case bottom as well as the USB-C port on the right (the…
Created a spacer so I could add GPIO headers and a bit more space for larger battery. Short M2 screws needed to hold the spacer on. Make sure there is enough clearance as the front cover screws use the same thread. You can probably…
This is a simple wrist attachment mount for the M5Stack Cardputer! This mount lets you easily attach and detach the device from your wrist using the devices built-in lego attachment points, and (optionally) four 2x4mm magnets. I think it…
Project Homepage: https://lerndinge.at/wp/logobox/ Deutsch: https://www.youtube.com/watch?v=Clfm1RqYyrE Deutsch: Die Logobox wurde für den Einsatz in der Primarstufe entwickelt. Angepasst an den kognitiven Entwicklungsstand sollen mit…
You can keep the whole logo blue/black or choose to color it with the original colors like i did (in your slicer). I printed mine in PLA/High speed PLA using 3 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height on a…
The M5Stack Cardputer Modular Expander is an extension board designed to enhance the capabilities of the M5Stack Cardputer. This expander provides you oportunity to add add additional modules: WIFI external antenna, CC1101, IR Transmitter…
M5Stack Cardputer is interesting piece of hardware. It's quite hard to use when flat on the desk. This angled stand will raise it by 15°. Stick rubber feet to bottom to stop it for sliding. The stand slots into LEGO-compatible holes on…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
m2.5x10mm screws switch 4mm https://s.click.aliexpress.com/e/_mqZWCq0
A simple remix of hippazoid case but for the Cardputer ADV version and the M5Stack logo. I kept the original parameters for the print: 2 walls, 3 top/bottom layers, 15% gyroid infill and 0.2mm layer height.
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
The M5Stack Cardputer pins extender, gives to opportunity to use 8 extended pins [ 5V, GND, G1, G2, CLK, DAT0, CMD, 3.3V ]. Throw this pins you can easily attached CC1101 , NRF and more other modules. For assembling process and additional…
This is a Flat shelf to support the shelves found here: https://www.printables.com/model/712125-multigrid-shelves-for-the-multiboard-storage-syste
M5Stack Cardputer Front Protector
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
Just a lid for the cardputer that clips over the top.
Back plate for M5Stack Cardputer enabling easy modifications (via provided .f3d file) , or change with origial one. Remix it as you like. You maybe will need to increase tolerances becouse I tried to make all holes as tight as possible.…
Full Recreation of the Original Project from the Contest Dez 22 Print as Slow as you can for MAX Precision as the Corners need to be Perfect If you like to see the “First” of this projects in 2008 search! [2008-04-18] MC Escher lizard…
Warning: In asembly you will NEED hot glue gun for glueing battery module to the plastic frame-thing also be aware and do not overtight screws otherwise screw holes will break off. Antena mod for cardputer providing extended wifi and…
Recommended to print at 5% infill with additional wall support. No supports needed and no screws or other fixings. Clean up the posts and check they are not too tight before placing the Cardputer on too firmly, it should lift off with…
This is an xPod variant of the Pusi Negotiator . An unofficially designed negotiator for wave filters to be used with the xBloom Studio xPods. Thanks to EAF member @wonderllama for the dimensions of the xPods. Brewing note: I recommend…
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
Super simple and durable jackpad with a hexagonal design on top for grip. Designed to be printed in 95A TPU without any supports. I went with 6 walls and 60% grid infill to make it strong and resilient while retaining just a little bit of…
A storage case for the Cardputer ADV with the LoRa Cap (with the included stock antenna). External case can be printed using your choice of material-PLA, PETG, ABS, etc. The inserts should ideally be printed in TPU for shock absorption…
Habe die Pumpe vor Jahrzehnten für meinen CNC-Kurs angefertigt. Aus Aluminium, Messing, Plexiglas und vier Schrauben M4. Drehte sich auch mit Druckluft. Die beiden Zahnräder sind 0,2 mm kürzer und auch 0,2 mm weniger im Durchmesser als…
M5Stack Card Computer (Cardputer) Mount compatible with Ikea Skadis Pegboards. Designed in FreeCAD. “split” 3mf file splits model into two pieces if a higher infill percentage is prefered for the back. Otherwise use the STL.
Eu fiz essa case para o cardputer por hobbie , e esto disponibilizando para quem quiser seguir s mesmos passos , por livre e espontanea vontade assim como um remix por terceiros , estaras livres… Para quem for fazer esteja ciente que…
In TPU 85A gedruckt ist es ein idealer Ersatzteil für viele SKS Fahrradpumpen. Kann gedreht werden und somit für Fahrrad- und auch Autoventile benutzt werden.
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
This stand will allow you to neatly mount your M5card computer on your IKEA Skais board.
M5Stamp cover to fit in place of factory one if external antena mod is installed. Needs special cable routing (or change in model) to work properly (see photos) Print settings: 0.2mm layer height no supports
A case i created, i couldnt find any case to store my cardputer in so i created this one :)
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. Case 3D – CAP RF | Cardputer…
I designed this magnetic mount to bolt to the Rubigrid inside my truck. It prints in 3 pieces. First, the AMPS mount base, which can be installed on an appropriately sized Rubigrid or mounted to a dash with VHB tape. (If mounting to a…
For People that lost their Power button.
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
I have designed an IKEA TIDPUNKT curtain bracket and am sharing the 3D files. There are 3 versions available, so choose the one that best fits your needs.
Designed to hold an air pump for bicycles. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 50% Filament: Doesn't matter PETG, ABS Doesn't matter. I chose Black Notes: Each…
This is a remix of the front panel for Cardputer ADV XL — External 2.8” Display Mod - Free 3D Print Model - MakerWorld With this model you have to remove the header pins and the SD slot from the screen. This model also has the screws for…
Cardputer ADV Adapter to fit raspberry pi inside More details here: https://www.reddit.com/r/CardPuter/comments/1t4skou/cardputer_zero_diy/
A NAVTEX (NAVigational TEleX) is an international automated direct-printing service (working in medium frequency) for delivery of navigational and meteorological warnings and forecasts, as well as urgent maritime safety messages to ships.…
Allows you to mount an m5stack Cardputer to the Cooler Master Qube 540 PC case
Das Gewinde der Halterung wird von innen durch die Sockenpuppe gestochen und von aussen wird das Horn aufgeschraubt.
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
hi, just a quick idea. That actually works very well. I find one can't really control the fore when pulling on the filament. So this little device helps you to control the first centimetres. Printed in PLA and fixed the “Bolts” with a…
I wanted to bring my Cardputer on a plane, and i thought that, for how already it looks like some sort of detonator, the additional battery and the two magnets would have made things even more difficult :P The mesh is all messed up cause…
Der Kuhne Oscar Phase 4 Up-Converter "MKU UP 2424 B" kann jetzt um das neue externe Display "KU EDPU 5.0" erweitert werden. Dieses externe Gerät wird über ein berührungsempfindliches Display bedient und liegt in der Regel auf dem Tisch.…
Montageclip zur Wand- Deckenmontage für halbierte Poolnudeln. Als Türpuffer z.b. für die Garage etc. Passender Poolnudelhalbierer unter https://www.thingiverse.com/thing:6614722 Category: Parts
This is a remix designed especially for mudpuddles. I believe that the original was made for water in a pool cover (generally clean water), but I wanted something to suck the water out of holes dug in the ground that have filled with…
staci do krabicky vlozit kostku do pisoaru a zavesit nekde do motoroveho prostoru a kuna už nepřijde
do you remember the boglins from back then? they were really cool. so this is my take on it. exactly like the boglins back then, a lot of motion just comes from the thin elastic material. its a nostalgia trip. print the boglin with tpu,…
Bei rechteckigen Duschabflüssen, die ca. 25cm x 9cm groß sind, kann dieser Adapter für den Schraubanschluss einer Handpumpe (Siehe Bilder) gedruckt werden. Ich weiß nicht, ob dieser Schraubanschluss standardisiert ist, aber alle Maße…
This is a visor clip for the m5 Stack Cardputer ADV with the Lora HAT on it. I printed this with Matte PLA on a Bambu X2D.
PodPuck is a minimalist wireless charging solution for AirPods Pro 2, compatible with the Apple Watch Magnetic Charger. AirPods Compatibility: I have verified compatibility with AirPods Pro 2 USB-C. Charger Compatibility: Apple has…
This fits the M5Stack cardputer with a place to put the antenna on the back. It'll fit the non-mesh cardputer as well as the mesh version. This is generated using build123d, AI was used in the creation of the relevant python code.…
A compact Gridfinity holder for the original M5Stack Cardputer K132, with storage for four microSD cards and two full-size SD cards or SD adapters. The Cardputer stands on its long, thicker edge next to the screen. This keeps the holder…
A literal and functional hat for the Cardputer ADV. Houses Adafruit I2S Stereo Decoder - UDA1334A Breakout (or a clone). The Cardputer's speaker and aux are mono by default. This board connects to the Cardputer's gpio pins and allows…
Summary Minimalist hardcase for your M5 Cardputer — designed to protect both the display and keyboard. A small opening on the bottom allows you to easily push the device out when needed. If you’d like to support my work, you can also…
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
Stand for the M5Stack Cardputer-ADV. The pegs are not a friction fit, just for locating. There are pockets for 5x3mm magnets to hold the Cardputer to the stand. Designed to work well with the Cap LoRa-1262 module attached
This is a mechanical reference (dummy) model of the Cardputer , intended for designing custom enclosures, mounts and accessories . The model represents the overall dimensions and main external features of the device and is not a printable…
I made a CC1101 for my Cardputer ADV following Ray J's tutorial on YouTube and decided to design a case for it. Here's the tutorial on how to make the CC1101: Can be printed without supports. I believe the spacers I printed for the device…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
I wanted to put my Cardputer up on my HSW, but could not find an appropriate holder for that, so I quickly made one. I like having a lanyard on my cardputer, so that model accommodates that by having holes in the bottom.
"reference model" using marketing materials, a bunch of models off grabcad, hopes, dreams... etc Not perfect, Work in progress, basic reference only. Just release the files M5...
I've modeled the title name and a stand to create a small diorama using both a resin and a fdm printer and some pillow interior. The car model was ripped from the official game files. For the resin prints there are both the .stl and the…
Modelo criado de forma independente para usuários do equipamento, sem fins lucrativos e sem qualquer vínculo, afiliação ou aprovação da fabricante. Todas as marcas pertencem aos seus respectivos proprietários. =VISUALIZEM AS IMAGENS= 🔧…
⚠ Atenção – Modificação necessária no CC1101 Para utilizar esta case, é obrigatório alterar a posição do conector de antena do CC1101 de horizontal para vertical . Essa mudança é necessária para que o módulo encaixe corretamente no espaço…
The better-half loves her Gladpure soap dispensers, but not the dripping, so I made her a drip tray. I printed it in PETG, however PLA works just as well.
Fits on the centreline just ahead of the wand pushrod support - try to get it as far aft as possible whilst still being able to insert & remove the pin. I attached it to the boat with 3M dual lock tape. I've added a second version (the v2…
Jestli tisknete hnědou tak: obalte papírem (toaleťák, noviny, kuchyňské ubrousky,…) a pak zavěšte pokud stříbrnou tak: jen zavěste Funguje to tak protože vosy jsou teritoriální a snaží se vyhýbat již zabranému území. Jakmile někde…
