Liczymy pasujące modele…
Intended to be used in the Formd T1 case in 3 slot configuration with the air cooling holy trinity: Thermalright AXP-x47 Full Copper Noctua NF-A9x14 Noctua NA-FD1 The pegs are designed to be friction fit and clear the fan retainer clips.…
The NA-FD1 fan duct kit makes it possible to significantly improve the performance of Noctua NH-L9i and NH-L9a series CPU coolers in Small Form Factor (SFF) environments where there is a gap of 5mm or more (up to 45mm) between the cooler…
needed a airtight connection (3D Print exhaust) and this was the best solution
Update 2021-02-24: If you're looking for an 88mm height, take a look at Sharkoctopus's remix at https://www.thingiverse.com/thing:4754084 which locks the pieces to each other all the way up. Update 2020-09-23: francisesmodewhite found it…
I remixed this model from the original Noctua design to fit into my Asrock Deskmini X600 with the Noctua NH-L9a-AM5 fan. It should be suitable for the AMD AM4 and L9i (Intel) version and Deskmini X300 as well. You just need 4x 20mm M3…
The original Noctua NA-FD1 model had the mounting holes sized for M3 screws rather than being the same size hole if you had purchased it from retail. The mounting holes have been widened to 5.6mm in diameter to fit the Duct Peg for AXP-90…
2x 60mm Fan for 110-220V AC (20mm thick) 2x M12x1.5 cable strain relief cable with 2 strands to connect cylinder head fan 4x M4x30 with hex socket to replace cyclinder head screws 8x M4x25 to mount fans 8x M4x10 for mounting motor fan…
Found @davidhbrown model to be a perfect fit on my bed, I went ahead and remodeled the whole thing in F360 in 1 single part. Should be almost a 1:1 replica from his FreeCAD model. The "upper_pins" might be slightly different, but should…
This tray is a resized remix of @sblomfield trays for the Commercial Chef CCD100W6 / Westinghouse WFD100 utilizing infill meshing. It is sized to fit precisely between the stacked plastic trays which come with the dehydrator. Top and…
As asked I post my remix of the noctua fan duct for my asrock deskmini X300 case. I first added some holes so only 5mm of the original hole's depth is left and I can use 20mm M3 screws. Then I added some more cuts so I can close the case…
New wheel for Sencor SFD128E food dryer Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0,2mm Infill: 100% Filament: PETG, PP Category: DIY
This is made to fit on the bottom tray of a Commercial Chef (Westinghouse WFD100W) Filament Dryer/ Food Dehydrator. Nine ¼" inch Ball Bearings roll inside a track allowing the spool resting above it to spin effortlessly. (honestly, it…
Replacement for GV-EFD1100 IP dome camera. Tabs broke off the original. Used a heat gun to pop the polycarb dome out. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Category: Camera
This is a replica of a faceplate for the NEC FD1165 series 8-inch floppy disk drives. In particular the FD1165-A was often built into the chassis of the NEC Advanced Personal Computer, and a drive re-used from such a machine will lack the…
Fridge Eggholder for Hanseatic HFD18983CI / Ikea Ribbenås Mirror file to get the other half Kühlschrank Eierhalter für Hanseatic HFD18983CI / Ikea Ribbenås Datei spiegeln um die andere Hälfte zu bekommen
Also has counterbored screw holes to allow the duct to be flush against the side panel. Uses M3x45 screws. MODCASE MASS
This is a remix of David H. Brown's " Dehydrator Tray Extension for Commercial Chef CCD100W6 (formerly Westinghouse WFD100W) ". It is designed as a single piece extension tray for the somewhat larger Westinghouse WFD101W model dehydrator…
General Information This model contains components to assemble a fuselage frame section for an R/C aircraft. The bulkhead and corner pieces are designed to be self jigging during assembly (i.e. they should snap together and hold their…
General Information This model contains components to assemble nose and tail fairings for an R/C aircraft. These components use a common bulkhead to which nose and tail shapes can be adapted. You will need to bond the pieces together…
Bracket that holds in the panes of glass in the Mirolin FD Series shower door. This bracket is identified as FD19. Recommend printing in PETG with 60% gyroid infill and 5 walls.
