Liczymy pasujące modele…
The Pontiac Fiero Mid-Engine Two Seat Coupe from 1987 was different from previous years due to the “Aeronose” front and rear. This particular body style was never offered from Plastic Model manufacturers. Since I own one of these cars I…
LEGO Pontiac Fiero GT 1988
Pontiac Fiero Gauge cluster trim print at .2 layer height
Pontiac Fiero, firebird, and camaro window switch replacement.
Pontiac Fiero SE with and without wing 1/32 for the pioneer mustang chassis.
Formula slot body for the pontiac fiero. resembling the coup 87 and 88.
Pontiac Fiero Aux Gauge Cluster Trim .2 layer height print in petg high temp or abs.
Pontiac Fiero Auto switch plate. You will need the prndl plate the clear slider plate and the reflective light plate from your current auto plate and move them over once these pieces are put together.
Replacement lens for the four overhead lights. This part needs to be printed using PETG or similar CLEAR plastic to avoid heat problems. It is recommended to replace the bulbs with LEDs as well to reduce any risk of damage, however…
Windshield sprayer holder i used the following one from amazon. Print it with the nozzle holder down on the build plate no supports in asa. Amazon.com: 2Packs Front Windshield Washer Nozzle, VVNIAA Wiper Spray Kit for Jeeps, replaces OEM:…
Pontiac Fiero Manual plate beefed up .2 layer height
This is a replacement piece for the proprietary bolt/washer combo that the Pontiac Fiero uses to attach the plastic door skins to the metal door frame. This is designed to be used with the a standard countersunk (flathead) M6-1.0 x 16 mm…
This plate replaces the ashtray and ashtray door in a Pontiac Fiero. You must remove the ashtray door and ashtray and then drop the plate into the area. You may want to remove the lamp to prevent heat damage or replace the lamp with an…
Pontiac Fiero manual plate mod .2 layer height
A way for your odb2 ecm cars to see all the data without a tablet or phone needed.
Print in abs or high temp petg. .2 layer height.
My glovebox shattered. This assembly replaces it with a printable version that provides a tiny bit more room and would be easy to print since it is “boxy” and not curved like the factory glovebox. Note that only one wedge is shown; you…
This is the drop in vent screw holder that always breaks
Sense you really cant buy one of these anywhere here is a printable version that does seem to be a bit of an upgrade. Make sure you print out of something like ABS/ASA and use supports to avoid warping and balance issues. and I recommend…
This is a glue on addition to the fiero cup holder on thingiverse. It allows you to have an upright area. It is a glue in drop in addition to Fiero ashtray cupholder by keycaps - Thingiverse . I use the area for my phone to sit upright…
Blank instrument bezel, you can design a file for whatever holes you need and use it as a modifier in the slicer to customize
keychain for the Fiero SE, its oversized, but i scaled mine to 30% x and y, and 120% z. Designed for singer extruder.
Cupholders for my dad's '86 Fiero, but I think it should fit for other models. You will need to hit separate into objects to separate this into 2 parts. Its the “O” button at the top of Prusa Slicer Needs 2 m3x8 bolts and 2 nuts To…
If your Fiero front hood (frunk) will not open because the main cable or the emergency cable has failed then it may be due to disintegration of the cable block at the latch rather than a broken cable. If the block crumbles then the cable…
Made this to save money when my Fiero broke down. Recommend you print with PETG or ABS.
Tired of fighting with the Fiero Door Skin bolts that are buried in plastic that strip out when you try to remove them? I know I am after messing a few of them up trying to remove them. This washer is designed to be used with a metric cap…
I couldn't find a model I liked to delete the sun visors on my Pontaic Fiero so I made this one. Super simple but it fits and gets the job done using the stock screws. Duplicate and mirror the model so you have a left and right side.
My plastic locking lever was missing on my car, so I made a new one! It clips well into the stock metal rod and has side grooves for new felt. I bought some from Amazon for 6$ for a massive roll, and I have both the lever, and the swatch…
steering rack bushing
Just sits in either ashtray in a fiero. Made for a '86 but should work in other years. Printed flat side down Designed for an S22 in a phone case, if it dosnt fit your phone lmk and ill make a new version for you.
GM fiero, firebird, camaro, bucket seat bushing. i was redoing my seats and my bushings were missing or destroyed .
Different door design for the cluts 3d hotwheels key holder
This tool allows you to open/close your 88 Fiero Headlights with a cordless drill. I took a phillips/flathead bit, cut the flathead part off and used it for the shaft that goes in the drill. The bit it just friction fit into the tool. The…
fender replacement washer
A token for Crash Derby that uses a model of a 1985 Pontiac Fiero I made
Printed in TPU 95a filament. I used 20% infill, you will need supports enabled for the outer lip of the part. It is a 2 piece design, slip the split inner bushing over the cable, apply a liberal amount of PVC primer to at least one side,…
Printed in TPU 95a filament. I used 20% infill, you will need supports enabled for the outer lip of the part. It is a 2 piece design, install the outer bushing into the firewall, slip the inner bushing over the cable, apply a liberal…
This is a phone holder designed to fit in the center console slot of a Pontiac Fiero and hold a 3.1"x6.2" (79x157mm) induction charger. The specific charger used was a LOOSAN pad type charger my buddy sourced, though I've included both an…
This allows you to rebuild your charcoal canister and make it future serviceable at the same time. Sand ~1/16" off the bottom of the canister, tap around the edge to break the bond and remove the old bottom. Use epoxy to install the…
Blank instrument bezel, you can design a file for whatever holes you need and use it as a modifier in the slicer to customize
