Liczymy pasujące modele…
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the 10inch_TP-Link_SG108.stl by https://www.printables.com/@mariusbach_1431080 since the TPLink SG108 is roughly the same size as the Netgear Switch. Printed…
This is a 10" rack mount for a Netgear ProSafe GS108Ev3 network switch. This model assumes you have the 4 round stock rubber feet under the switch. Printed in PLA with a 0.4mm nozzle using 0.2mm SPEED preset with adaptive cubic infill.…
10" rack mount for Netgear ProSAFE Gigabit switch GS108 (maybe others). It has one kestone slot on each side of the switch. Designed to fit my 10" 2020 rack. When inserthing the switch the sides will need to flex out a bit in the rear,…
Brackets for mounting a Netgear GS108 switch to the Multiboard mounting system. You will need to print 4xHandsOnKatie_Standard-Underware-Connector from the original remix file library.
Über den Parameter “Spalt” kann der Freiraum für den Switch verändert werden. In der ersten Veröffentlichten Version stand er auf 0,2 mm, jetzt ist er 0,5 mm und liefert etwas mehr Freiraum.
This is a remix of the design https://www.thingiverse.com/thing:1322695 . For a smoother fit I made it 1mm bigger in the inside and added a honeycomb pattern to it. The switch can be mounted under a table, on the wall or wherever you can…
A simple bracket for the Netgear GS108E . It has small holes so you can see the power LED and retain access to the factory reset button. It fits very snugly and you'll have to relocate the rubber pads slightly (or you can remove them…
This is a remix of the design https://www.thingiverse.com/thing:1322695 . I seperated the model and added some support, so you can print it also on smaller printers and you are more flexible to mount. You have to mirror the parts in your…
For my simple Homelab, I needed a Rackmount for my old DGS-108 Switch (12 Ports, 1 Gbps). The print in in two parts : The support and the “ears” I used some super glue to fix them together. (Yeah, I used too much glue so I have white…
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the design from @BrianBerkley. Printed face down, 2 versions are available to be used with/without M3 metallic threaded inserts. 2 screws M3x10 are required…
This is a rack mount kit for the Netgear GS108 switch designed for a 10-inch rack. The kit comprises three parts that can be 3D printed without the need of support. The clamps must be secured to the main part using two small screws. I…
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
Rack mount ears for Netgear GS108E switch. Remember to hold switch while pluging cables to prevent it from moving to the back. I've added a hole on each ear for the switch feets. Inspired by: https://www.thingiverse.com/thing:249851 Print…
If your 10-inch network cabinet is full to bursting with technology, this holder will save you some ⅓ U space. It can be supplemented with 4 M3 inserts on the sides so that you can additionally fix the switch to the side with M3 10mm…
A simple system of hooks to hang a Netgear GS108 switch ( https://www.netgear.com/be/business/wired/switches/unmanaged/gs108/ ) on an Ikea Skadis pegboard ( https://www.ikea.com/be/en/p/skadis-pegboard-black-50534378/ ).
If you like the model, I would appreciate if you leave a ❤ like. Rack Mount Bracket for Netgear GS108 This bracket is designed specifically for the Netgear GS108 switch, offering a clean and secure fit in your 10-inch rack setup. Features…
10" Rack Shelf for Netgear GS108T & Wemos S2 Mini Relay Board. Relay board space can be fill with an empty shelf.
This is a Pegboard mount for a Netgear GS108T switch. It has a 75mm spacing between the mounting holes and uses a standard 1"X1"X1/4" U.S. peg Board. Pictures are from version 1. Version 2 has the holes to reduce some of the plastic.…
I have two 8 port switches stacked and I wanted to them to hang them on my multiboard system. Due to room on my wall I preferred to have them stacked instead of next to each other, so I assembled the orginal brackets to an assembled one…
If you want to attach your wifi box
A bracket for a structured media panel to hold a NetGear GS108. I know there are improvements to make, such as something to hold the back end of the switch, so feel free to improve if you even want to. Just need two pins for structured…
Tplink SG108 modular rack mount likely also fits netgear GS108 requires 1u rails, recommended to print with ASA https://www.printables.com/@LvL_Dani_470947/collections/2036642
Based on a Makerworld posting adjusted for two switches
I created this for to work with the Mini Server Rack, which can be found printables.com/model/108975-19cm-network-rack I printed it with PETG, worked pretty well. a little tight I forgot about the feet to the switch when I was modeling…
A friction wall mount for the Netgear GS108E 8-port switch. Attach the model labeled “SwitchSide” to the switch using 6-8 mm long M3 screws. The cavity on the switch should be deep enough to allow an M3 nut to fit in the wall mount slots.…
A Netgear GS108 frontblende so the LEDs are covered and don't light the room at night.
Supports the "Raspberry Pi rack case or rack cluster" thing found here: https://www.thingiverse.com/thing:2795195 Designed to sit over the top of a Netgear GS108 (but might work for other small 8-port network switches too). The holes in…
Rack Mount Bracket for Netgear GS108 8-Port Network Switch
Bracket to mount a Netgear GS108E (v4, metal housing 158 × 101 × 29 mm) in a Hager volta multimedia enclosure. Ports face up, the switch stays open on all sides for cooling. How it works The switch hangs on two printed hooks using its own…
10" Rack Shelf for Netgear GS108T & Wemos S2 Mini Relay Board. Relay board space can be fill with an empty shelf.
Check description of original model here: https://www.printables.com/model/793696-rack-system-module-netgear-gs108ge If you like this model please hit the LIKE button. It helps me collect the prusameters. You may also liked some of these…
Description @EvilProphet made a really nice system called ESRack. Expanding on it. The ESRack system includes the following components: Mounting Brackets - used to install the unit in the rack, available in 3 sizes: Short Medium Long…
NetGear GS108 mount for the stacking raspberry pi mount . The mount is printed in two parts to eliminate the need for supports. I hate cleaning supports off parts, so this was my way around that. There is a little space between the insert…
This is a cage to mount a Netgear GS108 vertically to a table using the great Desk Clamp by hein . You need to remove the small rubber feet of the Netgear switch to be able to slide it into the mounting cage. Print with supports required.
Netgear GS108 Mounting kit for 19" rack system. Massive/robust case, enough print it from PETG. The four parts can fixing together with M3x25mm screw and M3 square nut. (for the side screw expedient panhead with wood washer, the upper…
Description The design is optimized for 3D printing. Thanks to clever angles, the model prints almost entirely without the need for cumbersome support structures—saving time, filament, and post-processing. The minimal support structures…
A rack mount for the Netgear GS108 switch, that fits 19 inch racks. The design is modular as it is half width, so other components could be mounted on the other half (by making a compatible mount) if you only have one switch to mount.…
Remixed print from Thingiverse. I just opened up the ventilation area more from the the original design. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Extended Rafts: No Supports: Yes Resolution: .2 Infill: 10% Category:…
I've used a Skadis pegboard as the backplate for my network cupboard for a while. I had used velcro to attach all of my devices - but my Netgear GS108Tv2 switch is heavy enough that it has been sinking over time, so I've made a mounting…
