Liczymy pasujące modele…
Jewellery Tree ,Hang jewellery from branches ,branches have holes for ear rings etc .Tray for smaller bits .Tree and cat glued to tray.Tray has recesses underneath to add weight ,stops unit falling over.I glued steel into recesses 55mm x…
remixed https://www.thingiverse.com/thing:4905821 to have 4 racks and removable base for flat printing. Have not tried to print, hope it works. Holds 40 pairs of earrings or 80 individual earrings.
I needed something simple so my wife can put her jewellery in one spot, away from cats' paws. Print instructions Print with no supports, any material will do. Prints fit tightly into one another, no need for glue.
Modell by TVVGGE from Thingiverse. Just wanted to share here too. Printed the one on the cover in 0.1mm in PETG Prusament Signal White without supports. If I were to print it again, however, I would use PLA instead of PETG.
If you like my work and enjoy my models please consider leaving me a tip/donation, It helps me to continue creating awesome models for you for free. https://paypal.me/muddymaker I designed a pirates treasure chest for the boys and the…
We saw https://www.thingiverse.com/thing:3375898 and thought this looked beautiful, so we printed it, then my sons girlfriend wanted to turn it into a jewellery box, so I imported it into Tinkercad, cut TVVGGE's base extended it and…
Found this jewellery tree on Thingiverse and wanted to design a mount for my Skadis pegboard. It uses the Skadis T-Clip System by Will and has 2-3 mounting points, depending on the version. The original was quite small, so I scaled it to…
A heart shaped jewellery box with a rose on the top. Print Settings Rafts: No Supports: Yes Notes: You will need supports for the lid. Do a filament change to green then again to red Post-Printing May need a bit heat If the lid is tight…
A remix of @dgo42_867207 's “Jewelry Hand” model (which itself is a remix of imaterialise 's “Jewelry Hand” model). A two hand jewellery stand with each hand slightly slanted outwards so they are suitable for easy hanging of rings,…
Jewellers / Model Makers Vice You can rotate the workpiece 360 degrees and tilt over to 40 degrees. The top ring of the base is designed to provide resistance on the ball with out it being fully locked. There is a locking screw on the…
this is an easy to print low poly jewellery holder for all sorts of jewellery needs
Hier ein Schmuckständer für Ketten Ringe und sonstiges Kleinzeug und könnt es skalieren wie Ihr es braucht. Ihr benötigt nach dem drucken noch Kleber. Viel Spaß Ergänzung der 3 Teile als einzelne Objekte Update vom 05.07.2023: Print in…
Combo box for earrings and rest of jewallery addons. Earrings wall as separate part for printing in horizontal orientation and passible to usable individually.
Chest of drawers for storing trinkets or jewellery. Can be printed at a range of layer heights, images shown are printed with the body at 0.3 µm and drawers, feet and handles at 0.2 µm. Print body and all 4 drawers, then print 4x drawer…
Holder for some earrings. Holders on the back can be used for 5 chains or rings.
I added the cutouts in the frame to save on time and material but this will still be quite a long and heavy print. ~9h for the frame ~2h for large drawers (x2) ~1.5h for small drawers (8x). ~0.5h for the hooks. So around 25h of print time…
The other half never puts her jewellery away and prefers to sling it all in a small bowl at the end of the day. She then has to fish out the items she needs the next morning. So, I made her this organiser tray array that consists of 17…
Happy Valentines Day! If you need to send flower ,jewellery and little surprise to your girl friend or wife, just make this model and fufill all these things.
Designed as a simple jewellery box insert or tray. To replace the one that was stolen by thieves! :( openscad source is included in case someone wants it as a base for something else.
A fun pie dish shaped jewellery dish. Printing and Assembly The dish shown in photos was printed at 0.2mm layer heights using a 0.4mm Nozzle. It should print well with larger nozzles, although the crisp edges may become more rounded.…
This Jewellery Tree Stand consists of 3 parts. NO SUPPORTS OR GLUE NEEDED!!!
Printed in 0.2mm White Nebula PLA No supports needed Printed on Elegoo Neptune 3 Pro
This modern, simple jewellery tree hanger is the perfect storage solution for necklaces. It is 3D printed and made of wood, giving it a stylish and sleek look. It is designed to keep necklaces secure and organized, perfect for any bedroom…
If you like my work and enjoy my models please consider leaving me a tip/donation, It helps me to continue creating awesome models for you for free. https://paypal.me/muddymaker Coffin Jewellery Box. You'll need 4 8x3mm neodymium magnets.…
I designed this jewellery box to resemble a carousel. When you turn the little ball on the top of the “tent”, the four drawers will slide out from the sides. Ideal for storing a few small items like rings and small neclaces. Here's a tip:…
I designed this when I was struggling to find a way to display handmade keyrings at craft shows. But could be used for hanging necklaces or bracelets as well. The top piece has a slit in it to be able to place a sign on top to display…
A jewellery box / small container made to look like the Round Tower in Copenhagen, complete with its internal spiral slope. To print: For all 4 parts (RoundTowerBody, RoundTowerObservatory, RoundTowerRoof, RoundTowerPin): 20% infill 0.4mm…
If you like my work and enjoy my models please consider leaving me a tip/donation, It helps me to continue creating awesome models for you for free. https://paypal.me/muddymaker Crystal Jewellery Stand. Step file included for those that…
The divider can sit in the bottom of the drawer and the trays can stack on top. The dimensions are 211mm x 100mm x 11mm tall. 0.3mm, PLA, Sovol SV01
Print 1x base and 3x peg - depending on your printer pegs may need a drop of super glue... or not :)
Box für Uhren, kette, Ringe und schmuck. Kann aber auch für andere nützliche Dinge als verstauraum genutzt werden.
No supports or glue are needed. Jewelry stand designed to hold long necklaces. It is 25 cm tall in total, with a 20 cm base and a 15 cm top section. It is designed to hold 18 hooks, allowing for 18 necklaces.
This is a small tray insert for the Stackers jewellery box Classic Trinket layer, for holding stud earrings. Each tray fits exactly into one of the compartments and can hold 4 large pairs of stud earrings or more if the earrings are…
Yet another resin calibration object, hopefully we don't need these some day. -Designed specifically for jewellers to slot stones of 6mm, 5mm, 4mm, 3mm, 2mm, 1.5mm, and 1mm and test exactly how accurate a resin print will be in reality.…
Reworked the 3d model from Scan the wrold: https://www.myminifactory.com/object/3d-print-gayer-anderson-cat-at-the-british-museum-london-4010 Added cup to be used as an egg cup or Jewellery holder. Please note for egg cup you will need to…
This is a design for a Trinket Tray. Re-size as necessary. 3 Models attached. You can customise these by selecting "Add part" on your slicer and adding Text and centring it. See pictures for example. For private use only. For donations or…
I needed a holder/stand for my keyrings, so I came up with this idea and made it with hidden magnets so that it could be put together with little effort. No clue is needed. Only some support for the "arms". I have printed it in PETG for…
This jewellery hanger showcases George Russell in one of his well-known celebratory or race-ready poses, transformed into a sleek, minimalist accessory stand. The design incorporates hooks and slots strategically placed along the…
Print Settings: Layer: height:0,2 perimeters: 3 solid layers: top4 bottom4 Infill: 10% Support:none Advanced: extrusion width: default: 0,45 first layer: 0,45 perimeter: 0,45 external perimeter: 0,45 infill: 0,4 solid infill: 0,7 top…
A basic jewellery & ring holder with crystal ore design
Foldable Jewellery Organiser Jewellery organisers come in two versions. Each design is stored in its own folder and the main difference lies in the first box containing a jewellery-holding panel while the other has space for a mirror…
A holder for up to 60 2.35mm rotary bits. Space beneath each for a 12mm high label (standard Ptape) for organisation. Comes in two versions: the basic bit holder the bit holder with a lip and a lid.
This is a 9-sided tool holder (why 9? Why not!) that I designed specifically for separating out my jewellery files into identical cuts, but it could be used with anything, really. Pencils, wood files, paintbrushes… anything that would fit…
I designed this jewellery stand for my wife. It is possible to use some cork or similar to improve the look and feel. Print settings 0.4 nozzle 0.2 layer height 4 wall loops only little support for the joint (see screenshot) tested with…
Jewellery tree like hanger, printable without supports, easy to assemble,
Can display 15-16 Pairs or earrings and 18 necklaces, remaining things can be divided in the compartments below
My wife has a number of fine gold chains that invariably tangle if stored in a jewellery box, and she's has been asking me for a solution... so here it is. Designed in OpenSCAD, so the design can be varied to suit the materials you have…
Boxes of different heights. For clips, hairpins and other hair accessories. A low box suitable for jewelry. The boxes can be placed on top of each other nicely. Printable without supports.
I printed it in woodfill fillament, but I guess almost all other types will also be fine. Used bluetag to attach it to the inside of a mirror cabinet. I printed with a layerheight of 0.15mm and a 0.6mm nozzle.
A compact Jewellery Box where you can save your special objects. On this box you have differents compartments where you can store rings, necklaces, watches, bracelets, earrings.
A jig for cutting thick wire or metal tubes with a jeweller's saw. Requires 3x M5x6 heat-set inserts and 2x M5 bolts. Slots for mounting to a desk or board with 4mm or #8 wood screws (countersunk). 3 parts: 1x Sled: has a 45 degree slot…
A jewellery box with removable and interchangeable compartments based on the need.
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
A really useful handle to place your jewellers files into for extra grip! Instead of using the thin handles with the rubber grip you can push the whole file (including the rubber grip) into the file handle and with friction it will stay…
My wife likes making jewellery and wanted a tool to model the wire she uses into various size shapes so I designed 2 tools for this purpose with metric measurements on them Square tool forms wire to the following sizes…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
Organize in Style: The Modern Hexagon Valet Tray Transform daily clutter into a curated display. Designed for the discerning individual, our valet tray’s sharp, architectural lines make a bold statement on any desk or nightstand. The…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
A wall mounted set of hooks to hang jewellery on. 2 hook options
Introducing the Modular Jewellery Organiser Drawer System , a customisable 3D-printable solution for organising and storing jewelry. This modular drawer system is designed for flexibility, allowing you to mix and match inserts for…
70 mm high tin nice design with lid. Both parts dont need any support material during the print. The models are designed with Fusion 360 !
Arrange the tray the way you need it. New inlays incoming soon :)
Anglo-Saxon Style Jewellery Box. Pretty little box to keep items you've pillaged in.
This compact jewelry hanger spins using a lazy Susan bearing, giving you easy access to your accessories. Designed with multiple hooks and slots, it can hold bracelets, chains, rings, and more—perfect for keeping your collection…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
Ajax MotionProtect Plus Jeweller. Justerbart væg- og hjørne montering beslag Designet til Ajax MotionProtect Plus Jeweller med fokus på fleksibel opsætning, nem 3D-print og enkel montering på både væg- og hjørnemontering. Funktioner…
This model was designed to address a very common issue all of us face, Whether you have a small safe or a big safe it is always unorganized with cash , jewellery or any other valuable's always laying around unorganized. This safety box…
i love making pendants, rings and similar stuff out of silver or nickel silver, (or alpaca as we call it in Argentina). one of the more tedious tasks is the sanding.. and some times there are small parts where only sand paper could be…
Made of two parts. Both are very easy to print, without supports. Enjoy.
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
This inlay for a jewellery box consists of two parts. The lower part is only a cross to separate the box into 4 compartments. The upper part has 4 boxes with a base and walls
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
This little Container I have designed for my GF, she has lost everxtime and everywhere lost her jewellery. One day I thought it was enough and this is the result of it... The thread is M 60 x 1mm. Print Settings Printer Brand: Creality…
My wife has several brooches, jewellery, that you have to attach to clothing by means of a safety pin. However this makes two holes in the fabric. This gadget corrects that. It is a holder for a thin magnet (20 x 2 mm). Together with…
A holder to attach this magnifier to your Honeycomb Storage Wall. Whichever way you print it, you're going to need supports I'm afraid. I printed mine in the orientation you see in the pictures, and the support is a bit ugly, so you might…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
hinge pins are 1.75mm filament that will be cut after instalation. standart size candle is required, 35 mm dia. lithopane should be 117x61x4 mm outher dimensions.
This is a two-part holder to mount the Trendsetter jewellery practice wheels onto the Jura inside ring vise. It comes in two parts, both printable without supports. It slides in between the various gaps in a Trendsetter practice wheel to…
simple handle for those cheap 30X36 magnifying glass thingy. commontly used for identifying pests or plants, jewelry, rocks, resin, coins, stamps… simply print and press it on. if a little bit too small give it a slight filing. it is…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
This is the lootable rare item from the video game, The Cycle: Frontier. Item Description: A simple and easy way to carry ones riches and memories. Also very easy to lose during an emergency evacuation.
A magnetic spring sheet bed is going to assist greatly as it will keep the magnets securely in place in the event of any collisions, however, a glass bed should also work. Ensure your hot end is non-ferrous (standard copper nozzles are…
This model was originally created for large colllectible coins called ‘Fauna and flóra’ ( more about it in the end ), but you can appreciate it for your own purpose (any other collectible coins, jewellery or other things you want to store…
The cuff prints flat. You can use hot water or a hairdryer to heat up the PLA and bend it to fit your wrist. Please use caution when working with heat. I bent it to shape and then spray painted the cuff. If you print the individual…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
Print configurations: Scale: 200% - since model is a bit small Support: No Infill: 15 - 20% Nozzle: 0.6mm
A simple and slim 45-degree angled mounting bracket designed for the Ajax GlassProtect Jeweller glass break sensor. This mount is useful when you need to install the sensor at an angle. Hardware required: 2× M3×8mm screws (to attach the…
/////////////////////////////////////////////////////////////////// https://www.paypal.com/paypalme/satch5150 ///////////////////////////////////////////////////////////////////
The whole thing was uploaded once as a complete part and divided into two parts which should fit most printers in terms of size
A modern fluted jewellery tray with a removable divider insert. Ribbed sides, clean lines, and it looks store-bought on a dresser or vanity. What's included (2 STL files) Tray: 175 x 100 x 46 mm, fluted sides - Divider insert: open…
A stand for a jewellery set (earrings + necklace + ring)
At the moment, this is the latest version
hair tie holder with ring storage, and space for knick knacks
![Hive Displays [embedded magnet modular jewellery displays]](https://media.printables.com/media/prints/99010/images/1001456_18aea9f2-46dd-4c01-8361-0db7b1b48811/prusa_mid_print.jpg)
