Liczymy pasujące modele…
K98 Style Bayonet Lug for MLOK Interfaces. Print orientation and supports as shown MLOK nuts required If you need anything, feel free to reach out! Questions/Suggestions/Criticism is highly appreciated. Happy Printing…
Wydruk około 1,10 €–1,35 € nettoWstępna wycena jednego wariantu
This is a remix of the race truck body by MarkerDave created for the WLToys K989 1/28th scale RC car. I've added some details to the body, closed the holes in the front and made it lighter. Width is 75mm. The body can be mounted perfectly…
This is a self-designed body for a WL-toys K989 rc car. The design is based on the SAAB 9-3 sportscombi but with a wide bodykit to fit the dimensions of the K989 chassis and a Hirsch inspired wing in the back. I modeled the body in…
A set of drift wheels for the WLToys K989 rc car. There is a right and left wheel so that the angle of the spokes look the same. But there is no problem with putting them on either side of the car. I have printed these wheels in both PLA…
Tesla Cybertruck for WLToys K989 chassis. You'll need 6 screws M2x6mm Print it with 2 perimeter and 15% infill. Chassis: http://bit.ly/3ur6jBr 6x M2 x 6mm Screw: http://bit.ly/3jy205c Go and check out my other bodies for this chassis. Cab…
After breaking a lot of stock chopsticks, here is a reinforced edition. It is also more precise and limits the play at the wheels. Choose the right STL version for your balls : 3.4 - 3.5mm are for stock plastic hub carriers, and 3.5 -…
I designed this steering knuckle for my k969 because mine broke
I printed in PETG, 0,2 mm, 4 perimeters.
This is another body for the WLToys K989 chassis. This time it's a Low Rider Delivery Truck. Print it with 2 perimeter and 15% infill. Chassis: http://bit.ly/3ur6jBr 2x M2 x 6mm Screws: http://bit.ly/3jy205c 2x M2 x 10mm Screws…
This is a larger bumper than the stock one to protect your front drive train while driving your car fast. It can prevent breaking the turnbuckles, A-arms or steering hub carriers in case of front impact. This is compatible with WLtoys…
I printed both parts in PLA. For smooth drifting you will have to sand down any imperfections, but it isn't necessary.
Parts for wltoys- rc cars
This is a remix of the E3DBuggy for the WLToys K989 1/28th scale RC car. With this chassis you'll have a functioning rolling E3DBuggy. The body can be mounted perfectly to the chassis. Print it with 2 perimeter and 15% infill. Have fun…
A cover to prevent dirt, dust or small stones getting to the gears. (This is a remix of Dionarap's design.)
This is my self-designed wheel with a separate rim and tire. This is a design that prints the rim separate from the tire to be able to swap the tires for different materials. I have printed the tire both in PLA and TPU. Print Settings…
WLtoys K989 or K969 (brushless) motor mount, uses original hardware and fits without modifying the chassis
Replacement servo horn for the 284131 (and k9x9) with smaller holes to allow moving to outer hole and increasing steering angle. Holes are 1mm which is very tight but works. Modify / drill the hole out a little if you want an easier time…
Custom rims (wheels) for Wltoys K969, K989 or 284131. Can be printed with 2 colors without a special multicolor printer. Just add a stop a the right height in the slicer and change the filament during the print. The holes are very tight,…
This is a remix of my cab over race truck to make a cab forward version. Body is created for the WLToys K989 1/28th scale RC car ( http://bit.ly/3ur6jBr ). The body can be mounted perfectly to the chassis. Print it with 2 perimeter and…
the stock rear part is broken easily, so I found a model and fixed some geometry issue and enforced it. enjoy! here is a small video on how it drives :) and one more updated: just broke the same part on the other model 284131 - and it…
Give extra clearance to your K989 with this 50mm wheels. Also increase track width to 102mm. Rim are compatible with 43.2x22 lego tires. This is not compatible with the default body shell, the wheels rub on it when you turn. Rims are in…
WLToys - Work/Display stand Introducing the ultimate display and work stand for your 1/28 WLToys RC car! Designed for both hardcore enthusiasts and casual tinkerers, this stand is like a throne for your miniature speed demon. This stand…
This is a custom body post designed for the K989 RC car. The front and rear body posts are slightly different to accommodate the front shocks. They are designed to be used with a neodymium magnet with a diameter of 10mm and a height of…
Last year, I set myself the challenge of designing a 1/28 scale radio-controlled car, and I’ve finally decided to share my model. This small RC is fast, it runs well and it's very fun to drive, but first and foremost, it's a truly fun…
Here's some wheels and tires for the WLtoys 284131. I printed the rims from PLA and the tires from 95A TPU. They get significantly less grip than the stock rubber tires which is fun for indoor drifting. I included some larger rims and…
This is V1.1 of the generic 1/28 scale race truck body designed for the WL-toys K989 chassis. This is an updated version of V1.0 https://www.printables.com/model/159977-generic-128-rc-race-truck-body The cabin is designed to be printed on…
Larger battery compartment for the WLtoys K989 but should fit other models. Category: R/C Vehicles
(setup) Just place down your foam mats in your desired layout and then make a race track out of my piece's. Just use the (hole, size guide),use the round one to start. Start by placing the guide vertical up and down and trace around the…
K989, 969 or Mini-Z Touring wheel
Thanks to Snowflake_3d !!! I found another body that i could "remix" to fit my WLtoys K989 DIY RC Car Recommended Print Settings Printer : Default Prusa Core One+ HF0.4 nozzle Print settings : Default 0.15mm Balanced Filament : Generic…
Third person FPV mount for the wltoys k989 (will fit other models) using a FTX cam01 FPV all in one camera. Camera mounts on the rear of the base plate using the two unused screw holes. Print Settings Printer Brand: Creality Printer:…
Thanks to Dominik Kutálek !!! I finally found a body that i could "remix" to fit my WLtoys K989 DIY RC car Required parts Magnets (4x) 10mm x 2.50mm Recommended Print Settings Printer : Default Prusa Core One+ HF0.4 nozzle Print settings…
This model adds adjustable-height feet to the Logitech Slim Solar+ K980. One of the slimmest keyboards on the market – and certainly the slimmest I ever owned – the Logitech Slim Solar+ K980 does not come with adjustable legs. While it is…
i have made a gear cover with 3 holes instead of 2 because the 2 holes doesn't fit on my wltoys k989
RC wheel and tyre for RC cars in 1/28 scale, particularly WLToys K989 and K969. Print in 0.1 mm layer height. Works with 0.4 mm nozzle, but 0.2 mm nozzle preferred. Post processing often required, remove strings by hitting it with a…
i coudn't find a workstand for my wltoys k989 so i made this one
This model adds fixed height feet to the Logitech Slim Solar+ K980. One of the slimmest keyboards on the market – and certainly the slimmest I ever owned – the Logitech Slim Solar+ K980 does not come with adjustable legs. While it is…
Thanks to Snowflake_3d !!! I found a body that i could "remix" to fit my WLtoys K989 DIY RC Car * For the red and black body, i used a black Sharpie to paint the windows ;-) Recommended Print Settings Printer : Default Prusa Core One+…
If someone needs to isolate capacitors outside of original PCB.... This is a part of my post on the blog about modifying Harman Kardon HK980. Since original design uses 2 capacitors and i went with 4 i decided to 3d print a holder/…
This was designed to isolate and space the pins of the bigger diodes to the smaller 2W06M pinout on my Harman Kardon HK980 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Resolution: 0,2 Infill: 20 or whatever…
Used Pla, no supports unless wanted. Use version two it works better and fits up to 6 bb's.
Used Pla, no supports unless wanted. Use version two it works better and fits up to 6 bb's.
![[WIP] MLOK K98 Bayonet Lug](https://media.printables.com/media/prints/478982/images/3925436_40cfe385-c51a-4403-9eb3-c8d7126cbb4e/bayonet-lug-watermark.jpeg)
