Liczymy pasujące modele…
Well, my bike got stolen and with it the light mounts, but I still have the bike lights. So here is a replacement. It mounts with O-ring sealing rings around a tube. There is a 5mm x 11mm hole to glue a magnet in. Pay attention to the…
I need to move my Knog Oi bell from the fatter part of my MTB handlebars to the thinner part but it wouldn't quite go small enough, even with the original smaller-bars adaptor. They sell a special smaller bell for that… So I designed this…
Mount for an Knog Blinder with Go Pro Mount on Garmin Bikemount. You need two Screws 3x14 and one 5x25. Also a self-locking Nut M5. All parts have been drawn by myself. Similarities to other parts by other designers are not intentional…
My Knog Cobber Mount broke. So i designed this replacement. The picture mounted to the bike is V1 i updated this design shown in the first picture. if you have an Prusa XL you can print it in place. else you just print the shell in petg…
SP Connect is secured by an anti-self-release system. To release from the SP Connect, simply press the levers while pulling the adapter out of the SP Connect system. I use this mount primarily for Knog Plus and GoPro. Recommendation:…
This is a remix of: https://www.thingiverse.com/thing:4608611 Material needed: Screw M4x16, Nut M4. Magnets Ø6mm. I used 2x 6x3 magnets. The magnets are press fit. Printed with Petg.
A saddle rail mount for Knog rear bike lights. Neatly tucks the Knog rear bike light under the saddle. Required for the model is M3 heat set inserts and M3x16 screws. Can be printed in PLA. I printed mine in carbon fiber reinforced nylon…
This bike accessory aims to look like the Knog Scout bike alarm. There's a hole to place a 3mm LED bulb. Fits on standard bottle cage holes (65mm appart, M5). Ideally to be printed with UV resistant filament, I've been using PLA with no…
My Knog Plus lights always switched themselves on in my pocket. So I built a magnetic holder that protects the on off switch. Additionally you can mount it to your backpack strap for ease of access. New version should be printed standing…
This is a remix of: https://www.thingiverse.com/thing:4608611 Material needed: Magnets Ø6mm. I used 2x 6x3 magnets. Screw M6x16 or M6x20. I replaced the original screw with this one. The magnets are press fit. Printed with Petg.
This solves a quite specific issue. It is an extension for you bike basket. If you are riding your bike with clip on light, that are supposed to go on the handle bar, but are also riding with a front basket, you run into the issue of…
This is an improved version of a Knog lamp attachment model published here https://www.thingiverse.com/thing:4915211. The model above was very week and did not last in terrain. This version is much more sturdy. Printed 100% infill and…
This model is a mounting solution for the Knog OI Bell (Small, 22.2mm) , allowing you to attach it to any bike equipped with a GoPro-style mount . I designed this for my Specialized Venge , as its aero handlebars don't have a good place…
This is a 3D-printable replica of the original Knog Scout cover, perfect for replacing a lost or broken one.
After my second Knog road broke the arm, I decided to make this one Have fun and post your makes! 20/09/20---> Uploaded a newer version (2.0), that made it thinner and better to use the power button Print Settings Printer Brand: Creality…
I love the Knog Lil Cobber lights but they have a really annoying flaw. The lights sometimes turn on by mistake when chucked in a bag. You then realised you are out of battery when you need them the most. The case has actually 3 benefits:…
A bit more secure than the O-ring mounts supplied with the KNOG Plus lamps. I designed and made these for my touring bike - a Kona Sutra LTD, but can be fitted to any fork with the hole in the crown for a reflector or hanger with an M5…
I've (poorly) mashed together a few models to mount a stepper motor along with the KNOG led clip to the front of the robak brace to allow for fpv head tracking. The brace and the Knog LED clip models were taken from the robak files while…
Running out of space on your seatpost? This saddle mount adapter lets you attach your bike light directly under the saddle instead. Whole section for mounting a light has around 2.4 cm. Designed specially for Knog Blinder. The bracket…
As I didn't have the same magnet but only 6x2mm one I recopied the shape and adapted it + some others mod. See below.
Add pause to the print before the magnet hole is covered up (around layer 42 at 0.28mm layer height). Make sure the magnet alignment is correct! No support required.
My Knog Light got damaged so I printed a bumper to protect it. It's printed with ninjaflex / TPU an fits tight. no supports needed. there's the studded "rock" version, and a more minimalistic one that gets's the job done as well Category:…
Print with flexible filament like TPU. I tested the version for the 27.2mm seat posts, the 31.6mm version is just an educated guess. But the design is parametric:…
This is a custom mount for the Knog Plus light , designed specifically for aerodynamic (aero) front forks . Inspired by the original Knog mount, this design allows you to attach your light to oval-shaped pipes. The oval sketch shape is…
Normaly the Knog OI is mounted to far to reach, due to shifting equipment and brakes. This handle makes it much easier to ring the bell, if your handlebar is full with stuff. Hopefully this will help other bikers ringing the bell much…
To prevent slipping, place rubber between the post and adapter for reliable fixation
Now you can perfectly hide your SmartTag under the Knog Blinder light. Uses M2 threaded inserts. Buy me a coffee, if you want :)
Da ich am Bike eine Sattelstützentasche habe war kein Platz für das Knog-Rücklicht. Also schnell einen Halter für die Sattelstrebe gezeichnet und nun braucht man keine Angst haben nicht gesehen zu werden.Magnetbohrung ist 4mm durchmesser…
Keep your Knog Blinder lights neatly organized and always ready to go with this simple 3D-printed wall mount. You can place the lights directly on the mount for quick access, or attach them securely using their straps. There’s also space…
This design is in one part and so use only: TPU for the body (has to be flexible to fit heat insert) 0.8 nozzle, 2 walls, 15% infill grid A CHC M3*20 screw A M3 washer A heat insert As this design is blind you have to twist the body on…
This series of seat post brackets is designed to attach Knog’s Plus Rear Light to various seat post designs, including round posts (25.4mm, 27.2mm, 30.9mm, 31.6mm) and the aero seat post on a Cervelo S2 (2010 - 2015). I plan to produce…
If you have a Knog Oi bell on your bike, but lost the hammer, here's a spare hammer. I found the ones that were available online inaccurate/not functioning. This one is tested and works fine. Many models are not available as original. I…
As my previous model was too attractive it has been stolen after only one night outside. So I designed one with screws. Two version in the tree: 22.2mm and 28.6mm Free to you to copy a body and then modify to your need. I used TPU and M3…
In order to keep all bike related items in one place I made a holder for my Knog Blinder 1300 bike light. Just attach some double sided tape to the back and mount it where ever you like.
Is the silicone strap on your Knog Blinder broken yet? If so, I've designed a case that allows you to attach the Knog Blinder to your handlebars without having to rely on their faulty silicone strap system. All you need to do is buy some…
This design is in one part and so use only: TPU for the body (has to be flexible to fit heat insert) 0.8 nozzle, 2 walls, 15% infill grid A CHC M3*20 screw A M3 washer A heat insert As this design is blind you have to twist the body on…
The light has a tripod thread on the back (1/4"-20), which secures the light into the mount and mount has two M5x6mmx7mm threaded inserts to screw it into a basket. The basket is https://oldmanmountain.com/product/basket/ , so you might…
Having multiple bikes and multiple Knog Plus lights to store, remixed the model created by dtxtr, giving me the capacity for 3 sets of lights all in one nice case (wall mounted). Even without magnets the original design works rather well,…
