42 modeli
Print without supports XT60 connector must be glued for convenient usage May be it fits also 7, 9 and 10 inch variants. Bonus: wires protection. Must be printed in vertical orientation. Alternative version for slightly smaller dimensions…
Tested on my HSKRC XL Frame (XL9 Arms), which is very close to the iFlight XL7. Standoffs in my case are 5mm (which could differ from the iFlight model), so the holes are tailored to that size. I added a TBS crossfire antenna holder to…
The MicroTrackRC is a small 3d printed tracked vehicle. It is designed to be easy to print and assemble and use very cheap readily available electronics but still be a very fun project to build and drive. I printed all the parts on two…
This is the logo of KRC Genk, a Belgian football team. For decoration purposes. Prints in 1 piece.
Quick and dirty vtx mount for the awkward and hard to mount Max solo VTX. Update April 2024: Added a version that connects the two and adds A holder for a radiomaster RP1 ELRS receiver Print in TPU 100% infill with no supports
HAKRC F722 40A AIO Flight Controller
Mount for DJI Air Unit O3 Camera. Holes for stands are 6mm Stand-Middle to Stand-Middle are 27mm
Print in the orientation shown in the slicer pic with tree supports. The softer the tpu the better since you will have a better time to fit gps in, as it's a tight squeeze Fits the HSKRC XL frames, as well as any frame that has a rear…
This slammed duct is designed to fit the Cloud-149, 149HD and Brave 163 drone frames (which apparently have the same mounting hole positions). The inner diameter is 78mm which gives about 1-2mm of prop clearance when using Nazgul Cine…
This duct is designed to fit the Cloud-149, 149HD and Brave 163 drone frames (which apparently have the same mounting hole positions). The inner diameter is 78mm which gives about 1-2mm of prop clearance when using Nazgul Cine 3040…
Use 80-100% infill and print out of tpu. use original screws to mount on top.
Ich habe diese Antennenhalterung designt. Das ist eine Speziell für die DJI O4 Air Unit Pro designte Antennenhalterung die die O4 Antennen vollständig schützt. Die Halterung geht auch für andere Frames ist aber für den HSKRC S5 V2 Frame…
Multipart printable logo of KRC Genk. Can be printed with multiple filaments and assembled later on. Goal is to put LED filaments in the body underneath the white elements. eg. Adafruit : https://www.adafruit.com/product/5504 Printed at…
This is a simple Crosstour CT9500 Mount for the HSKRC TWE210 Frame from the UAVfutures 99 build V2 (2018). Angle is 30°. Printed it with TPU from FilaFlex with 10% infill. I cut out some holes to reach the screws of the top plate.
The internal mesh of Joe's published meshes are a source of trouble for 3D printing. I rebuilt it so the internal corners are well-behaved. Joe's original design: https://www.thingiverse.com/thing:6384566 Joe's modified design for…
Spare replacement part A spare replacement power button for radio type AEG KRC 4368 DAB+. The original power button broke after some time of regular usage. As i was not able to procure the original part i created a model replacement. The…
Print Out of ABS or PETG, 100% infill. .16mm layers help as well.
New second version, much better. Print instructions Unassociated tags: HSKRC Freestyle 250 Category: R/C Vehicles Summary New second version, much better.
Enclosure for the KRC-86b bluetooth audio module
https://www.banggood.com/HSKRC-TWE210-210mm-Wheelbase-4mm-Arm-3K-Carbon-Fiber-X-Type-FPV-Racing-Frame-Kit-for-RC-Drone-p-1283150.html Category: R/C Vehicles
This is a model I made for the hskrc XL series frames that fits the walksnail v2 vtx. Print flat with supports for the small overhangs on the pillars, prefferably with tpu
Wanted to have a sturdy print to hold 3 components. XT60, VTX antenna and ELRS antenna. This is it. Tested by 'intentionally' crashing and it survived.
Mount for HSKRC Freestyle 250 with an angle of 20 deg for Gopro 3 series Video of Gopro3 black on HSKRC Freestyle 250 with this printed holder: https://www.youtube.com/watch?v=MYIt4LbvZA0 Print in TPU / Ninjaflex with 30% and 2 perimeter.…
The design is simple, lightweight, and installs without any additional hardware. All parts are designed to snap together, and the HmIP-KRCK can then be inserted directly into the holder. Print Settings Material: ABS or ASA (recommended)…
Fits Akaso V50 perfectly. Print on the side with tree supports, they easily pop off after.
For KingKong RC Lurker. Side vents to be printed with 0 top layer (infill according to taste) then glued with silicone to make the pocket behind watertight. Category: R/C Vehicles
This are legs with different hole locations for both arms on a HSKRC JOHNNY V2 frame. They are designed to be screwed with M3 screws that have max. tread lenght of 12mm and head lenght of 3mm.
After adding the bumpers from https://www.thingiverse.com/thing:3225137 to my drone, I couldn't get the stock rear cover to fit in anymore, so I quickly made a new one. Use material to your liking, I've used regular PLA, as that piece…
Taillight for KingKong RC Lurker. To be printed clear or translucent of course. Snaps into place (a bit on the tight fit side) Category: R/C Vehicles
I liked the original but I don't plan to use the roll cage and don't like to have all these screw poking. This remix is to be glued with silicone. Category: R/C Vehicles
Wandhalterung für HmIP -KRC4 KRCK KRCA KRC Fernbedienung Wall mount for HmIP -KRC4 KRCK KRCA KRC remote control
Replacement cap for Kross KRC 319WC, possibly it fits other models. Remamber to put rubber gasket to keep water out.
Hallo, ich habe dieses Modell designt. Das ist eine Kamerahalterung für die DJI O4 Air Unit Pro, speziell für den Frame HSKRC S5 V2 designt. Mir hat die Firma nämlich nur die Halterung für die O3 mitgeschickt, also habe ich die Halterung…
HSKRC 118 Arm Bumper and Motor Protection Should fit 15xx motors Feedback welcomed! Print Settings Printer: Tronxy D01 Filament: eSun TPU Category: R/C Vehicles
Caddx Peanut Mount for HSKRC 118 Requires M2 screw to secure peanut to the mount Printable in either TPU or PLA/PETG, but TPU is recommended. Mounts using the top cross standoff and using 2 cable ties to secure to frame Print Settings…
Videos of the Sherp show some equipped with mud flaps running all along the sides and extending to the rear. Sides are not needed and wouldn't be easy to connect to the Lurker but rear extension may help limiting water splashes to enter…
Wanted to offer some fresh air to my ESCs. Requires a modifier of max 116x44. On the modifier, set top and bottom layers to 0 and set your infill to taste (I've used Honeycomb at 25%). 9mm and 5mm heights available. Clip-on like original…
Hallo, ich habe dieses Modell designt. Das ist eine Kamerahalterung für die DJI O4 Air Unit Pro, speziell für den Frame HSKRC S5 V2 designt. Mir hat die Firma nämlich nur die Halterung für die O3 mitgeschickt, also habe ich die Halterung…
Ich habe diese Antennenhalterung designt. Das ist eine Speziell für die DJI O4 Air Unit Pro designte Antennenhalterung die die O4 Antennen vollständig schützt. Die Halterung geht auch für andere Frames ist aber für den HSKRC S5 V2 Frame…
Videos of the Sherp show some equipped with mud flaps running all along the sides and extending to the rear. Sides are not needed and wouldn't be easy to connect to the Lurker but rear extension may help limiting water splashes to enter…
3D printable topographic miniature of Prague, Krc - 🇨🇿 Czechia Capture the beauty of Prague, Krc 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates 50.040, 14.448…
